9L7245 PULLEY-AUXILIARY Caterpillar parts
3160, 3208, 613, 613B, 613C
Rating:
Alternative (cross code) number:
CA9L7245
9L-7245
9L7245
CA9L7245
9L-7245
9L7245
Weight: 12 pounds 5 kg.
Information:
DIAMETER OVER PINS
176.251
mm
GROOVE WIDTH
12.7
mm
NUMBER OF GROOVES
3
INDUSTRIAL ENGINE, WHEEL TRACTOR,
This part in 4 request:
Show.
This information for suppliers only!
2024-02-24
2022-10-12
2019-05-10
2019-03-13
Compatible equipment models: 9L7245:
Information:
Calibration Procedure for the AC Voltage
During the calibration procedures, voltages up to 600 V are present in the control panel.Do not short the terminals to ground with any part of the body or any conductive material. Loss of life or injury could result from electrical shock or injury from molten metal.
Note: Perform this procedure whenever the following components are replaced: AC Interface Board and System Controller Board. AC Current Calibration is also required.
Table 1
Required Tools    
Part Number     Description    
146-4080     Digital Multimeter    
Place the key switch in the Bypass position for the MMU that is being calibrated.Note: In a Single-Module System, place the key switch in the Bypass position on the System Cabinet.Note: Proceed to step 5 for Single-Module Systems.
Connect a PC to the Parallel Cabinet Interface Board that is located in the System Cabinet.
Illustration 1 g01051091
Rotate the switch on the Parallel Cabinet Interface Board to the corresponding Multiple Module Unit.Proceed to Step 6.
Illustration 2 g00839256
Illustration 3 g00840027
Remove all sheet metal panels. Remove the sheet metal panel for the System I/O and Isolation Board (2).
Connect a PC to the System RS232/RS485 port that is located on the System I/O and Isolation Board. Make sure that jumper Jmp1 (3) on the System I/O and Isolation Board is in the correct position.Note: The lower side is RS232 and the higher side is RS485.
Close the input circuit Breaker in order to restore power to the System.The System will initialize, but the key will remain at the Bypass position.
Initialize your Personal Computer.
Illustration 4 g00840053
Run UPS View by double clicking over the icon (4) on your PC.
Illustration 5 g01003395
Illustration 6 g01003391
Click over the "PC Settings" (7) in the Menu Bar.The "Connection" window will open.
Click on the radio button that is for the "Direct Connect (serial)" (5) .
Select your PC COM Port for this Serial Connection and set the Baud rate.The radio button for "Detailed MMU Telemetry" must be checked.
Click on "OK" Button (10) in order to accept these settings.
Illustration 7 g01003435
Click on "Connection" on the Menu Bar.
Select "Connect" from the drop-down menu.The PC will be connected to the System and the PC will receive the System Telemetry.
Illustration 8 g01003470
When the PC connects, click on "Enter Password" (13) in the Menu Bar.The window that is illustrated above will open.
Enter the username and enter the password.
Click on "OK" Button.After the Password has been entered, the Menu Option will Change.The Menu bar will contain a "Calibrate" option.Note: The vacuum for the Flywheel needs to be less than 58 mTorr before the system can start this calibration.
Illustration 9 g00840232
Click "Calibrate" on the drop-down menu.
Select "AC Voltages".The following events will occur.
The input contactor "K1" closes.
The output contactor "K2" closes.
The Static Switch turns on.
The DC Bus Voltage rises.
The "Calibration of a Channel" window opens. Refer to illustration 9.
Click on "View Status" button.Another "Calibration Group Status" window will open.Note: Drag the "Calibration Group Status" window aside if the view of the "Calibration of a Channel" window is blocked.
Click on "Use Defaults" on "Calibration of a Channel" window.You will be prompted to "Enter Calibration Point"
During the calibration procedures, voltages up to 600 V are present in the control panel.Do not short the terminals to ground with any part of the body or any conductive material. Loss of life or injury could result from electrical shock or injury from molten metal.
Note: Perform this procedure whenever the following components are replaced: AC Interface Board and System Controller Board. AC Current Calibration is also required.
Table 1
Required Tools    
Part Number     Description    
146-4080     Digital Multimeter    
Place the key switch in the Bypass position for the MMU that is being calibrated.Note: In a Single-Module System, place the key switch in the Bypass position on the System Cabinet.Note: Proceed to step 5 for Single-Module Systems.
Connect a PC to the Parallel Cabinet Interface Board that is located in the System Cabinet.
Illustration 1 g01051091
Rotate the switch on the Parallel Cabinet Interface Board to the corresponding Multiple Module Unit.Proceed to Step 6.
Illustration 2 g00839256
Illustration 3 g00840027
Remove all sheet metal panels. Remove the sheet metal panel for the System I/O and Isolation Board (2).
Connect a PC to the System RS232/RS485 port that is located on the System I/O and Isolation Board. Make sure that jumper Jmp1 (3) on the System I/O and Isolation Board is in the correct position.Note: The lower side is RS232 and the higher side is RS485.
Close the input circuit Breaker in order to restore power to the System.The System will initialize, but the key will remain at the Bypass position.
Initialize your Personal Computer.
Illustration 4 g00840053
Run UPS View by double clicking over the icon (4) on your PC.
Illustration 5 g01003395
Illustration 6 g01003391
Click over the "PC Settings" (7) in the Menu Bar.The "Connection" window will open.
Click on the radio button that is for the "Direct Connect (serial)" (5) .
Select your PC COM Port for this Serial Connection and set the Baud rate.The radio button for "Detailed MMU Telemetry" must be checked.
Click on "OK" Button (10) in order to accept these settings.
Illustration 7 g01003435
Click on "Connection" on the Menu Bar.
Select "Connect" from the drop-down menu.The PC will be connected to the System and the PC will receive the System Telemetry.
Illustration 8 g01003470
When the PC connects, click on "Enter Password" (13) in the Menu Bar.The window that is illustrated above will open.
Enter the username and enter the password.
Click on "OK" Button.After the Password has been entered, the Menu Option will Change.The Menu bar will contain a "Calibrate" option.Note: The vacuum for the Flywheel needs to be less than 58 mTorr before the system can start this calibration.
Illustration 9 g00840232
Click "Calibrate" on the drop-down menu.
Select "AC Voltages".The following events will occur.
The input contactor "K1" closes.
The output contactor "K2" closes.
The Static Switch turns on.
The DC Bus Voltage rises.
The "Calibration of a Channel" window opens. Refer to illustration 9.
Click on "View Status" button.Another "Calibration Group Status" window will open.Note: Drag the "Calibration Group Status" window aside if the view of the "Calibration of a Channel" window is blocked.
Click on "Use Defaults" on "Calibration of a Channel" window.You will be prompted to "Enter Calibration Point"
Caterpillar parts catalog:
Parts pulley Caterpillar catalog:
7C3912
PULLEY AS
3208
3208
9N3899
PULLEY-PUMP DRIVE
225, 3208, 613B, 613C, FB221, PR-1000, PS-500
225, 3208, 613B, 613C, FB221, PR-1000, PS-500
8S9381
PULLEY
613
613
8S8203
PULLEY
613
613
2P2507
PULLEY
613
613
2P4292
PULLEY
613
613
6N8913
PULLEY ASSEM. (idler)
613, 613B
613, 613B
6N3622
PULLEY
613
613
8N0806
PULLEY
613B
613B
4N7719
PULLEY
613
613
2P4617
PULLEY
613
613
2N1968
PULLEY-AUXILIARY DRIVE
225D, 3208
225D, 3208
2N0195
PULLEY-ALTERNATOR
3160, 3208, CS-551
3160, 3208, CS-551
1142706
PULLEY-ALTERNATOR
3116, 3126
3116, 3126
8L3523
PULLEY-ALTERNATOR
3116, 3126, 3208, 3304B, 3306B
3116, 3126, 3208, 3304B, 3306B
1004954
PULLEY
3116, 3126
3116, 3126
9N3899
PULLEY-PUMP DRIVE
225, 3208, 613B, 613C, FB221, PR-1000, PS-500
225, 3208, 613B, 613C, FB221, PR-1000, PS-500
1214685
PULLEY
3208
3208
1214682
PULLEY
3208
3208
7C3912
PULLEY AS
3208
3208
6I0680
PULLEY AS
3208
3208
2W4874
PULLEY GP
3208
3208