9Y3290 PULLEY Caterpillar parts
3116
Rating:
Alternative (cross code) number:
CA9Y3290
9Y-3290
9Y3290
CA9Y3290
9Y-3290
9Y3290
Weight: 5 pounds 2 kg.
Information:
DIAMETER OVER PINS
183.49
mm
GROOVE WIDTH
3.56
mm
NUMBER OF GROOVES
7
TRUCK ENGINE,
Compatible equipment models: 9Y3290:
Number on catalog scheme:
2
For full view, you need register
Information:
System Response:A Level 1 warning will be generated.Note: The resistance of the solenoid coil should be approximately 7 ohms at 20 °C (68.0 °F).Test Step 1. CHECK THE SOLENOID
Disconnect the solenoid from the machine harness.
At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire 780-PU(Purple)) to contact 2 (wire 235-BK(Black)).
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Observe the status of the CID 1530 FMI 05 diagnostic code. Expected Result:The CID 1530 FMI 05 diagnostic code is no longer active. A CID 1530 FMI 06 diagnostic code becomes active when the jumper wire is connected.Results:
YES - The CID 1530 FMI 05 diagnostic code is no longer active. A CID 1530 FMI 06 diagnostic code becomes active when the jumper wire is connected. The solenoid has failed.Repair: Repeat this Test Step "CHECK THE SOLENOID" in order to verify the solenoid failure.Temporarily connect a new solenoid to the harness. Do not install the solenoid. Verify that the replacement solenoid has cleared the diagnostic code. If the code is no longer active, permanently install the new solenoid. Verify that there are no active diagnostic codes for the solenoid. Clear any logged diagnostic codes.STOP
NO - The CID 1530 FMI 05 diagnostic code remains active. The jumper wire does not affect the status of the active diagnostic code. The solenoid is not the cause of the problem. Proceed to Test Step 2.Test Step 2. CHECK THE CIRCUIT FOR AN OPENThe jumper wire that was installed in the previous Test Step remains in place.
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the C2 connector of the switch panel from the switch panel.
At the connector C2 for the switch panel, measure the resistance from contact C2-13 (wire 780-PU(Purple)) to contact C2-2 (wire 235-BK(Black)).
While observing the multimeter resistance measurement, wiggle the machine harness connectors for the switch panel and wiggle the machine harness connector for the solenoid. Gently pull on the wires. Move the wires around. Expected Result:The resistance measurement is less than 5.0 ohms at all times during the manipulation of the harness and connectors.Results:
OK - The resistance measurement is less than 5.0 ohms. The resistance measurement is not indicating an open or a bad connection in the circuit. Proceed to Test Step 3.
NOT OK - The resistance measurement is greater than 5.0 ohms. The resistance measurement is indicating an open circuit or a bad connection in the machine harness.Repair: A resistance measurement that is greater than 5000 ohms could indicate that a wire is either not connected or that the wire is open. A resistance measurement greater than 5.0 ohms but less than 5000 ohms could indicate that one of the connection points is not a good connection.The open or the possible bad connection is in supply wire 780-PU(Purple) or in return wire 235-BK(Black) of the machine harness. Refer to the complete Electrical System Schematic of the machine. Check all of the connectors that
Disconnect the solenoid from the machine harness.
At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire 780-PU(Purple)) to contact 2 (wire 235-BK(Black)).
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Observe the status of the CID 1530 FMI 05 diagnostic code. Expected Result:The CID 1530 FMI 05 diagnostic code is no longer active. A CID 1530 FMI 06 diagnostic code becomes active when the jumper wire is connected.Results:
YES - The CID 1530 FMI 05 diagnostic code is no longer active. A CID 1530 FMI 06 diagnostic code becomes active when the jumper wire is connected. The solenoid has failed.Repair: Repeat this Test Step "CHECK THE SOLENOID" in order to verify the solenoid failure.Temporarily connect a new solenoid to the harness. Do not install the solenoid. Verify that the replacement solenoid has cleared the diagnostic code. If the code is no longer active, permanently install the new solenoid. Verify that there are no active diagnostic codes for the solenoid. Clear any logged diagnostic codes.STOP
NO - The CID 1530 FMI 05 diagnostic code remains active. The jumper wire does not affect the status of the active diagnostic code. The solenoid is not the cause of the problem. Proceed to Test Step 2.Test Step 2. CHECK THE CIRCUIT FOR AN OPENThe jumper wire that was installed in the previous Test Step remains in place.
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the C2 connector of the switch panel from the switch panel.
At the connector C2 for the switch panel, measure the resistance from contact C2-13 (wire 780-PU(Purple)) to contact C2-2 (wire 235-BK(Black)).
While observing the multimeter resistance measurement, wiggle the machine harness connectors for the switch panel and wiggle the machine harness connector for the solenoid. Gently pull on the wires. Move the wires around. Expected Result:The resistance measurement is less than 5.0 ohms at all times during the manipulation of the harness and connectors.Results:
OK - The resistance measurement is less than 5.0 ohms. The resistance measurement is not indicating an open or a bad connection in the circuit. Proceed to Test Step 3.
NOT OK - The resistance measurement is greater than 5.0 ohms. The resistance measurement is indicating an open circuit or a bad connection in the machine harness.Repair: A resistance measurement that is greater than 5000 ohms could indicate that a wire is either not connected or that the wire is open. A resistance measurement greater than 5.0 ohms but less than 5000 ohms could indicate that one of the connection points is not a good connection.The open or the possible bad connection is in supply wire 780-PU(Purple) or in return wire 235-BK(Black) of the machine harness. Refer to the complete Electrical System Schematic of the machine. Check all of the connectors that
Caterpillar parts catalog:
Parts pulley Caterpillar catalog:
205B, 214B, 3114, 3116, 3126, 3306, 3306B, 910E, 918F, 924F, 928F, 938F, 938G, AP-1000B, AP-1055B, AP-900B, BG-2455C, BG-245C, CB-434, CB-634, CB-634C, CP-563, CS-531, CS-531C, CS-533, CS-533C, CS-563...
3114, 3116, 3126, 3126B, 613C II, 950F, 953B, 953C, 963B, 963C, D8L, D9N, D9R
214B, 3114, 3116, 3126, 3126B, 550, 570, 574, 580, 613C II, 950F, 950F II, 953B, 953C, 960F, 962G, 963B, AP-1000, AP-1050, BG-2455C, BG-245C, CB-434, CB-634C, CB-634D, CP-563, CS-531C, CS-533C, CS-563...
120H, 120H ES, 120H NA, 135H, 135H NA, 30/30, 3114, 3116, 3126, 3126B, 3126E, 320B, 322B L, 322B LN, 322C, 322C FM, 325B L, 35, 446, 446B, 446D, 45, 525B, 533, 535B, 539, 543, 55, 550, 561M, 570, 574,...
120H, 120H ES, 120H NA, 135H, 135H NA, 214B, 30/30, 3114, 3116, 3126, 3126B, 3126E, 320 L, 320B, 322B L, 322B LN, 322C, 322C FM, 325, 325B, 325B L, 35, 446B, 446D, 45, 525B, 533, 535B, 539, 543, 55, 5...
3114, 3116, 3126, 533, 543, 918F, 924F, 950G, AP-1000, AP-1000B, AP-1050, AP-1055B, BG-2455C, BG-245C, CB-434, CB-634C, CB-634D, CP-563, CS-531C, CS-533C, CS-563C, CS-573C, CS-583C, D250D, IT12B, IT24...
3116, 3126, 3304, 3304B, 3306, 3306B, 330B L, 637D, CB-534, D250B, D250E, D250E II, D25C, D25D, D300B, D300D, D300E, D300E II, D30C, D350C, D35C, G3304B, G3306B
120H, 120H ES, 120H NA, 135H, 135H NA, 3114, 3116, 3126, 3126B, 3126E, 320B, 322B L, 322B LN, 322C, 322C FM, 325B L, 35, 446, 446B, 446D, 45, 525B, 535B, 539, 550, 561M, 570, 574, 580, 613C II, 814F I...
120H, 120H ES, 120H NA, 135H, 135H NA, 214B, 30/30, 3116, 3126, 3126B, 3126E, 320 L, 320B, 322B, 322B L, 322B LN, 322C, 322C FM, 325, 325B, 325B L, 35, 446B, 446D, 45, 525B, 535B, 539, 55, 550, 561M, ...
3116, 3126B, 3126E, 539, 550, 561M, 574, 928F, 938F, 938G, 950G, 953B, 953C, 962G, 963B, 963C, AP-1000B, AP-1055B, AP-900B, BG-2455C, BG-245C, D5M, D6M, IT28F, IT38F, IT38G, IT62G, M318
3116, CP-563
3116, 950F, CP-563, E200B, IT12B
7E6783
PULLEY
3176, 3176B
3176, 3176B
9Y3467
PULLEY
3176, 3176B
3176, 3176B
3176, 3176B, 3176C, 3196, 345B, 345B II, 345B II MH, 345B L, 365B, 365B L, 725, 730, C-10, C-12, W345B II
7C6349
PULLEY-ALTERNATOR
3114, 3116, 3126
3114, 3116, 3126
3406B, 3406C, 3406E, C-15, C-16
3176B
3176B, C-10, C-12, C11, C13, CX31-C13I, TH35-C13T
4P7490
PULLEY-CRANKSHAFT
3406B, 3406C, 3406E, C-15, C-16
3406B, 3406C, 3406E, C-15, C-16
3116, 3126, 3126B, 3126E