AVSPARE.COM
parts catalog

PUMP GP-WATER 0R9782 - Caterpillar


0R9782 PUMP GP-WATER Caterpillar parts
Rating:
11
Alternative (cross code) number:
CA0R9782
0R-9782
0R9782
Caterpillar 0R9782 PUMP GP-WATER
Weight: 28 pounds 12 kg.

Buy PUMP GP-WATER 0R9782 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$381.31
 

28 Jul 2022

US: # 1 Quality Par
Aftermarket replacement 196-0268/5.9L Turbocharger Cartridge, New
Generic 0R9782 1000-070-087T 1000070087T 171864 196-0268, , , , 5.9L, 5.9L, 5.9L, 5.9L, Turbocharger Cartridge, Turbocharger Cartridges, Turbo Cartridge, Turbo Cartridges, Cartridge, Cartridges, Cartridge Assembly, Cartridge Assemblies, Turbocharger Cartridge, Turbocharger Cartridge,
$560.00
 

17 Dec 2021

CN: xinyijidian
Turbocharger S200AG050 171859,0R9782,1960268,300200002 for Caterpillar 3126B
N\C Material: turbocharger made of special steel, resistant to high temperature, high pressure, high rotation capacity, improve service life || Applicable models: Turbocharger for Caterpillar 3126B engine S200AG050 171859,0R9782,1960268,300200002 || High efficiency: The use of turbochargers can increase engine power, improve engine emissions, reduce fuel consumption, and high transient response || Packaging: The turbocharger is packed with reinforced packaging to make the product more solid in the delivery process and ensure safe transportation || Note: Pour in clean oil before installation to prevent poor supply resulting in instantaneous lack of oil in the supercharger, affecting service life
$1,350.00
 

16 Nov 2021

CN: xinyijidian
Turbocharger S200AG050 3126B 171859 0R9782 1960268 300200002 for 2000 - Caterpillar 950,962 loader with engine 3126B
N\C
  For full view, you need register

Information:


Illustration 1 g01285332
Top View of the Blade Slope Sensor (1) Blade (2) Straight Edge (3) Blade Slope Sensor
Illustration 2 g01285398
Place one end of a 4 foot straight edge against the vertical edge of the blade slope sensor.
Hang a plumb bob off the other end of the straight edge.
Illustration 3 g01285466
Measure the horizontal distance from the blade to the string line of the plumb bob. Note the measurement.
Repeat Step 1 through Step 3 for the other side of the blade.
Subtract the two measurements.The result should be less than 12.7 mm (0.5 inch).If the result is greater than 12.7 mm (0.5 inch) proceed to Step 6. Otherwise, the blade slope sensor is properly mounted.
Loosen the bolts on the blade slope sensor.
Rotate the blade slope sensor in the direction that is needed.
Tighten the bolts.
Recheck the measurements.If the result is greater than 12.7 mm (0.5 inch), proceed to Step 10.Otherwise, the blade slope sensor is properly mounted.
Remove the bracket for the blade slope sensor. Reweld the bracket.Note: The fore/aft pitch of the bracket must be within 3 degrees of the fore/aft pitch of the platform (circle).


Parts pump Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.