1143336 PUMP GP-PISTON Caterpillar parts
D4C III, D5C III
Rating:
Alternative (cross code) number:
CA1143336
114-3336
1143336
CA1143336
114-3336
1143336
Weight: 221 pounds 100 kg.
TRACK-TYPE TRACTOR,
You can buy:
Number on catalog scheme:
6
For full view, you need register
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 187-2718 Filter Wrench 1 Start By:
Release the system pressure. Refer to Disassembly and Assembly, "System Pressure - Release".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Open the rear access door and turn the battery disconnect switch to the OFF position.
Drain the hydraulic oil from the hydraulic oil tank into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual for the correct procedure.
Open the engine access door on the right side of the machine.
Illustration 1 g03743695
Remove the nut, the washer, and wire assembly (3).
Loosen the clamp and remove hose (2) from the back side of filter base (1).
Disconnect hose assemblies (4) and (5) from filter base (1).
Use Tool (A) in order to remove filter (6). Remove filter (6) from filter base (1).
Remove the four bolts, the four washers, and filter base (1). Installation Procedure
Install filter base (1) in the reverse order of removal.
Install filter (6). Refer to Operation and Maintenance Manual, "Hydraulic System Oil Filter - Replace".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 187-2718 Filter Wrench 1 Start By:
Release the system pressure. Refer to Disassembly and Assembly, "System Pressure - Release".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Open the rear access door and turn the battery disconnect switch to the OFF position.
Drain the hydraulic oil from the hydraulic oil tank into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual for the correct procedure.
Open the engine access door on the right side of the machine.
Illustration 1 g03743695
Remove the nut, the washer, and wire assembly (3).
Loosen the clamp and remove hose (2) from the back side of filter base (1).
Disconnect hose assemblies (4) and (5) from filter base (1).
Use Tool (A) in order to remove filter (6). Remove filter (6) from filter base (1).
Remove the four bolts, the four washers, and filter base (1). Installation Procedure
Install filter base (1) in the reverse order of removal.
Install filter (6). Refer to Operation and Maintenance Manual, "Hydraulic System Oil Filter - Replace".
Parts pump Caterpillar catalog:
D3C III, D3G, D4C III, D4G, D5C III, D5G
315, 315B, 315B FM L, 315C, 317B LN, 318B, D3C III, D3G, D4C III, D4G, D5C III, D5G
939C, D4C III, D5C III
1283290
PUMP AS-FUEL INJECTION
D4C III, D4G
D4C III, D4G
1283291
PUMP GP-FUEL INJECTION
D4C III, D4G
D4C III, D4G
1690563
PUMP GP-PISTON
D4C III, D5C III
D4C III, D5C III
1887567
PUMP GP-PISTON
D4C III, D5C III
D4C III, D5C III
D4C III, D5C III
933, 933C, 939, 939C, D3C III, D4C III, D5C III
3044C, 933, 933C, 939, 939C, D3C III, D4C III, D5C III
315, 315B, 315C, 317B LN, 318B, D3C III, D3G, D4C III, D4G, D5C III, D5G
1139423
PUMP GP-PISTON
D4C III, D5C III
D4C III, D5C III
1455316
PUMP GP-CHARGE
D4C III, D5C III
D4C III, D5C III
1887255
PUMP GP-PISTON
D3C III
D3C III
1887247
PUMP GP-PISTON
D3C III
D3C III
1690560
PUMP GP-PISTON
D3C III
D3C III
1523351
PUMP GP-PISTON
D3C III
D3C III
1866593
PUMP GP-PISTON
D4C III, D5C III
D4C III, D5C III
1688328
PUMP GP-PISTON
D4C III, D5C III
D4C III, D5C III
1688326
PUMP GP-PISTON
D4C III, D5C III
D4C III, D5C III
1533541
PUMP GP-PISTON
D4C III, D5C III
D4C III, D5C III
1471475
PUMP GP-PISTON
D4C III, D5C III
D4C III, D5C III
1455284
PUMP GP-PISTON
D4C III, D5C III
D4C III, D5C III