1458689 PUMP GP-PISTON Caterpillar parts
CP-433C, CS-433C
Rating:
Alternative (cross code) number:
CA1458689
145-8689
1458689
CA1458689
145-8689
1458689
Weight: 95 pounds 43 kg.
VIBRATORY COMPACTOR,
This part in 2 request:
Show.
This information for suppliers only!
2021-09-15
2020-06-24
Number on catalog scheme:
1
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1 Start By:
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01343561
Typical example
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Remove bolts (6) and suction pipe (7).
Remove the joint from suction pipe (5) (not shown).
Loosen cap (2). Carefully remove cap (2) from the housing of engine oil pump (1). Note: The spring force will be released when the cap is removed.
Remove spring (4) from the bore for the relief valve in the housing of engine oil pump (1).
Use Tooling (A) to remove plunger (3) from the bore for the relief valve in the housing of engine oil pump (1). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01343561
Typical example
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Ensure that all components are clean and free from wear or damage. If necessary, replace any components that are worn or damaged. If the bore for the relief valve in the housing of engine oil pump (1) is worn or damaged, the complete assembly of the engine oil pump must be replaced.
Lubricate plunger (3) with clean engine oil. Use long nose pliers to install plunger (3) and spring (4) into the bore for the relief valve in the housing of engine oil pump (1). Note: The plunger must slide freely in the bore for the relief valve.
Install cap (2) to engine oil pump (1). Tighten the cap to a torque of 45 N m (33 lb ft). Note: Ensure that the spring is properly located inside the plunger and the cap.
Install suction pipe (7) and a new joint (5) (not shown) to the assembly of the engine oil pump.
Install bolts (6). Tighten the bolts to a torque to 22 N m (16 lb ft). End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1 Start By:
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01343561
Typical example
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Remove bolts (6) and suction pipe (7).
Remove the joint from suction pipe (5) (not shown).
Loosen cap (2). Carefully remove cap (2) from the housing of engine oil pump (1). Note: The spring force will be released when the cap is removed.
Remove spring (4) from the bore for the relief valve in the housing of engine oil pump (1).
Use Tooling (A) to remove plunger (3) from the bore for the relief valve in the housing of engine oil pump (1). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01343561
Typical example
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Ensure that all components are clean and free from wear or damage. If necessary, replace any components that are worn or damaged. If the bore for the relief valve in the housing of engine oil pump (1) is worn or damaged, the complete assembly of the engine oil pump must be replaced.
Lubricate plunger (3) with clean engine oil. Use long nose pliers to install plunger (3) and spring (4) into the bore for the relief valve in the housing of engine oil pump (1). Note: The plunger must slide freely in the bore for the relief valve.
Install cap (2) to engine oil pump (1). Tighten the cap to a torque of 45 N m (33 lb ft). Note: Ensure that the spring is properly located inside the plunger and the cap.
Install suction pipe (7) and a new joint (5) (not shown) to the assembly of the engine oil pump.
Install bolts (6). Tighten the bolts to a torque to 22 N m (16 lb ft). End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Caterpillar SIS machinery equipment:
Caterpillar SIS
CS-433C CP-433C Vibratory Compactor 2JM00001-UP (MACHINE) POWERED BY 3054 Engine »
145-8689
PUMP GP-PISTON
CP-433C CS-433C Vibratory Compactor 1ZN00001-UP (MACHINE) POWERED BY 3054 Engine »
145-8689
PUMP GP-PISTON
CS-433C COMPACTOR-MILITARY 1FS00001-UP (MACHINE) POWERED BY 3054 Engine »
145-8689
PUMP GP-PISTON
Caterpillar parts catalog:
Parts pump Caterpillar catalog:
3054, 3054B, 312B L, 416C, 416D, 424D, 426C, 428C, 436C, 438C, AP-800C, BG-225B, CB-434C, CB-534C, CB-535B, CP-433C, CS-323C, CS-431C, CS-433C, PF-290B, PS-150B, PS-200B, PS-300B, PS-360B, TH210, TH21...
3054, 307, 416B, 426B, 428B, 436B, 438B, CB-534B, CB-534C, CB-535B, CP-433C, CS-431C, PS-300B, TH103, TH62, TH63, TH82, TH83
3054, AP-800C, BG-225B, CB-534C, CP-433C, CS-431C, CS-433C, PF-290B, PS-200B, PS-300B, PS-360B, TH103, TH62, TH63, TH82, TH83
3054, 307, 312, 315, 317, 416B, 426B, 428B, 436B, 438B, AP-800C, BG-225B, CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545, CP-433C, CS-431C, TH103, TH62, TH63, TH82, TH83
3054, 307, 416B, 428B, CB-434B, CB-434C, CB-544, CB-545, CP-433C, CS-323C, CS-431C, TH62, TH63, TH82
3054, 3056, CB-534B, CB-535B, CP-433C, CS-323C, CS-431C, PS-200B, PS-300B
3054, 3054B, 307, 416B, 416C, 416D, 424D, 428B, 428C, CB-434B, CB-434C, CB-544, CB-545, CP-433C, CS-323C, CS-431C, PS-150B, TH210, TH215, TH62, TH63, TH82
3054, 3054B, 312, 312B L, 312C, 315, 315B L, 317, 416B, 416C, 416D, 420D, 426C, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 554, 908, 914G, AP-800C, BG-225B, BG-225C, CB-434C, CB-534B, CB-53...
3054, 3054B, 307, 312, 312C, 315, 315B L, 317, 416B, 416C, 426C, 428B, 428C, 436C, 438C, 914G, AP-800C, BG-225B, CB-434B, CB-434C, CB-534B, CB-534C, CB-544, CB-545, CP-433C, CS-323C, CS-431C, IT14G, M...
3054, 3056, 312B L, 416C, 426C, 428C, 436C, 438C, AP-800C, BG-225B, CB-434C, CB-534C, CB-535B, CP-433C, CS-323C, CS-431C, CS-433C, PF-290B, PS-150B, PS-200B, PS-300B, PS-360B, TH103, TH350B, TH460B, T...
3054, 3054B, 3056, 312B L, 312C, 315B L, 416C, 416D, 420D, 424D, 426C, 428C, 428D, 430D, 432D, 436C, 438C, 442D, 554, 908, 924G, 924GZ, AP-800C, BG-225B, BG-225C, CB-434C, CB-534C, CB-535B, CP-433C, C...
3054, 3054B, 312B L, 416D, 420D, 424D, 428D, 430D, 432D, 438D, 442D, 554, 908, 914G, AP-800C, BG-225B, BG-225C, CB-534B, CB-534C, CB-535B, CP-433C, CP-433E, CS-423E, CS-431C, CS-433C, IT14G, M315, PF-...
1992116
PUMP GP-ENGINE OIL
303, 304
303, 304
1061131
PUMP GP-PISTON
BG-2455C
BG-2455C
1101386
PUMP GP-VANE
953C
953C
1643167
PUMP & MTG GP-VIBRATORY
CB-534C, CB-634C
CB-534C, CB-634C
966D, 966F, R1700 II, R1700G
3N8722
PUMP & LINES GP
7211, 7221
7211, 7221
1052281
PUMP GP-PISTON
CP-433C
CP-433C
1283291
PUMP GP-FUEL INJECTION
D4C III, D4G
D4C III, D4G
2381219
PUMP GP-WATER
3011C, 3013C, C1.1, CB-14
3011C, 3013C, C1.1, CB-14
320B, 320B FM LL, 320B L