1505812 PUMP GP-PISTON Caterpillar parts
307B
Rating:
Alternative (cross code) number:
CA1505812
150-5812
1505812
CA1505812
150-5812
1505812
Weight: 105 pounds 47 kg.
MINI HYD EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
£14.78
13 Apr 2018
Ford: Ford
New Genuine Ford Focus ST / Mondeo / S-Max / Galaxy 2.5l Spark Plug (Single) 1505812
To Fit Focus models with 2.5L Duratec 220/225PS Engines From: 03-12-2007 Onwards || To Fit Mondeo models with 2.5 Duratec Petrol Engines From: 19-02-2007 Onwards || To Fit S-Max and Galaxy models with 2.5 Duratec Petrol Engines From: 06-03-2006 To 2015 || Genuine Ford Part || If you Are Unsure If this is the Correct Part for Your Car then Please double Check With us
To Fit Focus models with 2.5L Duratec 220/225PS Engines From: 03-12-2007 Onwards || To Fit Mondeo models with 2.5 Duratec Petrol Engines From: 19-02-2007 Onwards || To Fit S-Max and Galaxy models with 2.5 Duratec Petrol Engines From: 06-03-2006 To 2015 || Genuine Ford Part || If you Are Unsure If this is the Correct Part for Your Car then Please double Check With us
£28.74
13 Apr 2018
Ford: Ford
Ford Genuine Focus ST 2.5L 220/225PS Spark Plugs x 5. New,1505812
Genuine Part || Covered by Manufactures warranty || Perfect Fit
Genuine Part || Covered by Manufactures warranty || Perfect Fit
$17.98
23 Apr 2017
Brisk: Brisk
BRISK PERFORMANCE SPARK PLUG Replaces Ford 1505812 - w/ 360-degree electrode LKALADB
This part in 2 request:
Show.
This information for suppliers only!
2021-08-31
2017-11-10
Number on catalog scheme:
1
For full view, you need register
Compatible equipment models: 1505812:
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 390-1131 Timing Pin (Crankshaft) 1
B 435-3146 Timing Pin (Camshaft) 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components are clean and free from wear of damage. If necessary, replace any components that are worn or damaged.
If Tooling (A) and Tooling (B) are not installed, install Tooling (A) and install Tooling (B). Refer to Disassembly and Assembly, "Fuel Injection Pump Gear - Remove" for the correct procedure.
Illustration 1 g02937163
If necessary, install locating pin (6) into fuel injection pump shaft (7).
Ensure that locating pin (6) is 45 degrees from vertical and parallel to the center of Torx head plug (5), refer to Illustration 1.
Position gear (8) onto fuel injection pump shaft (7).
Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install" for the correct procedure.
Install the crankcase breather. Refer to Disassembly and Assembly, "Crankcase Breather - Install" for the correct procedure.
Illustration 2 g02937277
Remove Tooling (B) from the front housing.
Install new O-ring seal (1) to plug (2).
Install plug (2). Tighten the plug to a torque of 25 N m (221 lb in).
Remove Tooling (A) from the cylinder block.
Install new O-ring seal (3) to plug (4).
Install plug (4). Tighten the plug to a torque of 30 N m (266 lb in).
If equipped, install the accessory drive. Refer to Disassembly and Assembly, "Accessory Drive - Remove and Install" for the correct procedure.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 390-1131 Timing Pin (Crankshaft) 1
B 435-3146 Timing Pin (Camshaft) 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components are clean and free from wear of damage. If necessary, replace any components that are worn or damaged.
If Tooling (A) and Tooling (B) are not installed, install Tooling (A) and install Tooling (B). Refer to Disassembly and Assembly, "Fuel Injection Pump Gear - Remove" for the correct procedure.
Illustration 1 g02937163
If necessary, install locating pin (6) into fuel injection pump shaft (7).
Ensure that locating pin (6) is 45 degrees from vertical and parallel to the center of Torx head plug (5), refer to Illustration 1.
Position gear (8) onto fuel injection pump shaft (7).
Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install" for the correct procedure.
Install the crankcase breather. Refer to Disassembly and Assembly, "Crankcase Breather - Install" for the correct procedure.
Illustration 2 g02937277
Remove Tooling (B) from the front housing.
Install new O-ring seal (1) to plug (2).
Install plug (2). Tighten the plug to a torque of 25 N m (221 lb in).
Remove Tooling (A) from the cylinder block.
Install new O-ring seal (3) to plug (4).
Install plug (4). Tighten the plug to a torque of 30 N m (266 lb in).
If equipped, install the accessory drive. Refer to Disassembly and Assembly, "Accessory Drive - Remove and Install" for the correct procedure.
Caterpillar SIS machinery equipment:
Caterpillar SIS
307B Excavator AFB00001-UP (MACHINE) POWERED BY 4M40 Engine »
150-5812
PUMP GP-PISTON
307B TRACK-TYPE EXCAVATOR 5CW00001-UP (MACHINE) POWERED BY 4M40 ENGINE »
150-5812
DOUBLE PISTON PUMP
307B TRACK-TYPE EXCAVATOR /SWING BOOM ARRANGEME/ 6KZ00001-UP (MACHINE) POWERED BY 4M40 ENGINE »
150-5812
PUMP GP-DOUBLE PISTON
Caterpillar parts catalog:
Parts pump Caterpillar catalog:
307, 307B, 307C, 308C
1559059
PUMP GP-GEAR
307B
307B
1461978
PUMP AS-FUEL INJECTION
305.5, 306, 307B, 307C, 307D, 308C
305.5, 306, 307B, 307C, 307D, 308C
1781049
PUMP GP-FUEL
307B
307B
1090, 1190, 1190T, 1290T, 307B, 312B L, 312C, 315B L, 315C, 317B LN, 318B, 318C, 320B, D6M, M313C, M313D, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318C, M318C MH, M318D, M318D MH, M322C, M322D, ...
307, 307B, 308C, 315, 315B, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G, E120, E140, E70, E70B
2348824
PUMP GP-CHARGE
D4G, D5G
D4G, D5G
4403093
PUMP GP-FUEL PRIMING
XQC1200, XQC1600
XQC1200, XQC1600
1057646
PUMP & MTG GP-PROPEL
CP-433C
CP-433C
2228349
PUMP & MTG GP-MAIN HYDRAULIC
365C, 365C L, 365C L MH
365C, 365C L, 365C L MH
1660885
PUMP GP-SUMP
3412, 3412C
3412, 3412C
2246283
PUMP GP-GEAR
583T
583T
1715706
PUMP GP-PISTON
AP-1055B
AP-1055B