1629612 PUMP GP-FUEL TRANSFER Caterpillar parts
3126B, 322C, 325C, 561N, 938G II, 950G II, 953C, 962G II, 963C, C7, D5N, D6N, IT38G II, IT62G II, M325C MH, SPP101
Rating:
Alternative (cross code) number:
CA1629612
162-9612
1629612
CA1629612
162-9612
1629612
Weight: 4 pounds 2 kg.
EXCAVATOR, WHEELED EXCAVATOR,
Related part:
1629612
PUMP GP-FUEL
20R3428
R
You can buy:
US$313.95
28 May 2025
FridayParts
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
3178021 3186357 1491950 317-8021 318-6357 149-1950 162-9612 For E324D 325D 329D Oil Pump C7 C9 Engine Fuel Pump Excavator Parts
FEMKFAXF Quiet Operation : Advanced design reduces noise for a smoother driving experience. || Enhanced Fuel Efficiency : Delivers precise fuel supply to improve mileage and reduce emissions. || Smooth and Consistent Operation : Prevents engine stalling or hesitation with steady fuel pressure. || DIRECT REPLACEMENT : Designed to match OEM specifications for a seamless fit, no modifications required. || 3178021 3186357 1491950 317-8021 318-6357 149-1950 162-9612 For E324D 325D 329D Oil Pump C7 C9 Engine Fuel Pump Excavator Parts
FEMKFAXF Quiet Operation : Advanced design reduces noise for a smoother driving experience. || Enhanced Fuel Efficiency : Delivers precise fuel supply to improve mileage and reduce emissions. || Smooth and Consistent Operation : Prevents engine stalling or hesitation with steady fuel pressure. || DIRECT REPLACEMENT : Designed to match OEM specifications for a seamless fit, no modifications required. || 3178021 3186357 1491950 317-8021 318-6357 149-1950 162-9612 For E324D 325D 329D Oil Pump C7 C9 Engine Fuel Pump Excavator Parts
162-9612 1629612 Fuel Pump Diesel Engine High-pressure Oil Pump Compatible With CAT E325C Excavator 3126 Engine Gear Pump Fuel Transfer Pump
LIYOGWUL Wide applicability: The oil pump is suitable for various types of gasoline engines, such as engines, diesel engines, etc || Easy to install: Mechanical oil pump compact structure, reduce installation time and easy maintenance, reduce the cost of use || Enhanced driving experience: Engine lubrication pumps improve driving comfort and experience with low noise and smooth operation || Heat dissipation function: self-priming oil pump helps the engine heat dissipation through oil circulation, reduce the working temperature and better heat dissipation || 162-9612 1629612 Fuel Pump Diesel Engine High-pressure Oil Pump Compatible With E325C Excavator 3126 Engine Gear Pump Fuel Transfer Pump
LIYOGWUL Wide applicability: The oil pump is suitable for various types of gasoline engines, such as engines, diesel engines, etc || Easy to install: Mechanical oil pump compact structure, reduce installation time and easy maintenance, reduce the cost of use || Enhanced driving experience: Engine lubrication pumps improve driving comfort and experience with low noise and smooth operation || Heat dissipation function: self-priming oil pump helps the engine heat dissipation through oil circulation, reduce the working temperature and better heat dissipation || 162-9612 1629612 Fuel Pump Diesel Engine High-pressure Oil Pump Compatible With E325C Excavator 3126 Engine Gear Pump Fuel Transfer Pump
This part in 10 request:
Show.
This information for suppliers only!
2024-12-02
2024-12-02
2024-12-02
2024-12-02
2024-12-02
2024-12-02
2024-12-02
2023-09-14
2021-10-12
2017-09-19
Compatible equipment models: 1629612:
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9832 Engine Rollover Stand 1
B 8S-2328 Dial Indicator 1
C 334-0519 Grease -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00577390
If crankshaft gears (6) were removed, install crankshaft gears (6) on the crankshaft and install bolts (7).
Check the clearance of the bearings. Refer to Disassembly and Assembly, "Bearing Clearance - Check" for the correct procedure.
Illustration 2 g01353563Note: Place clean engine oil on the main bearings and on the connecting rod bearings prior to installation.Note: The upper halves of the main bearings have an oil hole in the center.
Install the upper halves of main bearings (8) in the cylinder block.
Install the upper halves of connecting rod bearings (9) in the connecting rod assemblies.
Illustration 3 g01353615
Typical example
Note: Ensure that the word "FRONT" that is on the end of the crankshaft is toward the front of the engine.
Attach a suitable lifting device to crankshaft (4) and position the crankshaft in the cylinder block. The weight of crankshaft (4) is approximately 762 kg (1680 lb).
Illustration 4 g01353620
Tightening sequence
Note: The main bearing caps must be installed with the word "FRONT" and the part number toward the front of the engine. Each main bearing cap has a number on the bottom surface and each main bearing must be installed in the corresponding position in the cylinder block.
Place Tooling (C) on the bolts for the main bearing caps.
Illustration 5 g01353682
Place clean engine oil on thrust plates (3). Install thrust plates (3) on each side of the center main bearing.
Place main bearing caps (5) into position and install the bolts. Tighten the bolts in the numerical sequence that is shown above to a torque of 190 14 N m (140 10 lb ft). Tighten the bolts again for an additional 180 5 degrees.
Check the end play with Tooling (B). The end play must not exceed 0.40 0.23 mm (0.0157 0.0091 inch).
Illustration 6 g01353696
Position the connecting rods on the journals of the crankshaft. Install connecting rod bearing caps (2). Note: The number that is on the side of the connecting rod caps must be installed next to the corresponding number that is on the side of the connecting rod.
Illustration 7 g01353701
Tightening sequence
Place Tooling (C) on the bolts for the connecting rod caps and install the bolts.
Tighten the bolts with the following steps:
Tighten bolts (14) and (15) to a torque of 90 5 N m (65 4 lb ft).
Tighten bolts (16) and (17) to a torque of 90 5 N m (65 4 lb ft).
Tighten bolts (14) and (15) again to a torque of 90 5 N m (65 4 lb ft).
Tighten bolts (16) and (17) again to a torque of 90 5 N m (65 4 lb ft).
Tighten each bolt for an additional 90 5 degrees (1/4 turn). An impact wrench may be used.
Place the remaining connecting rod caps in position and tighten the bolts with the same procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9832 Engine Rollover Stand 1
B 8S-2328 Dial Indicator 1
C 334-0519 Grease -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00577390
If crankshaft gears (6) were removed, install crankshaft gears (6) on the crankshaft and install bolts (7).
Check the clearance of the bearings. Refer to Disassembly and Assembly, "Bearing Clearance - Check" for the correct procedure.
Illustration 2 g01353563Note: Place clean engine oil on the main bearings and on the connecting rod bearings prior to installation.Note: The upper halves of the main bearings have an oil hole in the center.
Install the upper halves of main bearings (8) in the cylinder block.
Install the upper halves of connecting rod bearings (9) in the connecting rod assemblies.
Illustration 3 g01353615
Typical example
Note: Ensure that the word "FRONT" that is on the end of the crankshaft is toward the front of the engine.
Attach a suitable lifting device to crankshaft (4) and position the crankshaft in the cylinder block. The weight of crankshaft (4) is approximately 762 kg (1680 lb).
Illustration 4 g01353620
Tightening sequence
Note: The main bearing caps must be installed with the word "FRONT" and the part number toward the front of the engine. Each main bearing cap has a number on the bottom surface and each main bearing must be installed in the corresponding position in the cylinder block.
Place Tooling (C) on the bolts for the main bearing caps.
Illustration 5 g01353682
Place clean engine oil on thrust plates (3). Install thrust plates (3) on each side of the center main bearing.
Place main bearing caps (5) into position and install the bolts. Tighten the bolts in the numerical sequence that is shown above to a torque of 190 14 N m (140 10 lb ft). Tighten the bolts again for an additional 180 5 degrees.
Check the end play with Tooling (B). The end play must not exceed 0.40 0.23 mm (0.0157 0.0091 inch).
Illustration 6 g01353696
Position the connecting rods on the journals of the crankshaft. Install connecting rod bearing caps (2). Note: The number that is on the side of the connecting rod caps must be installed next to the corresponding number that is on the side of the connecting rod.
Illustration 7 g01353701
Tightening sequence
Place Tooling (C) on the bolts for the connecting rod caps and install the bolts.
Tighten the bolts with the following steps:
Tighten bolts (14) and (15) to a torque of 90 5 N m (65 4 lb ft).
Tighten bolts (16) and (17) to a torque of 90 5 N m (65 4 lb ft).
Tighten bolts (14) and (15) again to a torque of 90 5 N m (65 4 lb ft).
Tighten bolts (16) and (17) again to a torque of 90 5 N m (65 4 lb ft).
Tighten each bolt for an additional 90 5 degrees (1/4 turn). An impact wrench may be used.
Place the remaining connecting rod caps in position and tighten the bolts with the same procedure
Cat SIS web machinery list:
Parts pump Caterpillar catalog:
1130061
PUMP GP-METERING
938F, 938G, 938G II, IT38F, IT38G, IT38G II
938F, 938G, 938G II, IT38F, IT38G, IT38G II
2304176
PUMP GP-METERING
950G II, 950H, 962G II, 962H, 966G II, 966H, 972G II, 972H, 988H, IT62G II, IT62H
950G II, 950H, 962G II, 962H, 966G II, 966H, 972G II, 972H, 988H, IT62G II, IT62H
1052508
PUMP AS-FUEL PRIMING
120G, 12G, 12H, 12H ES, 12H NA, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 214B, 235, 3114, 3116, 3126, 3126B, 3126E, 3176, 3176B, 3176C, 3196,...
120G, 12G, 12H, 12H ES, 12H NA, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 214B, 235, 3114, 3116, 3126, 3126B, 3126E, 3176, 3176B, 3176C, 3196,...
1375541
PUMP GP-FUEL PRIMING
120G, 12G, 130G, 140G, 140H, 143H, 14G, 14H, 160G, 160H, 163H, 1673C, 16H, 235B, 24H, 3116, 311C, 311D LRR, 3126, 3126B, 3126E, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315C, 315D L,...
120G, 12G, 130G, 140G, 140H, 143H, 14G, 14H, 160G, 160H, 163H, 1673C, 16H, 235B, 24H, 3116, 311C, 311D LRR, 3126, 3126B, 3126E, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315C, 315D L,...
1898777
PUMP GP-ENGINE OIL
120H, 120H ES, 120H NA, 120K, 120K 2, 12K, 12M, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 160K, 30/30, 3116, 3126, 3126B, 3126E, 320B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L,...
120H, 120H ES, 120H NA, 120K, 120K 2, 12K, 12M, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 160K, 30/30, 3116, 3126, 3126B, 3126E, 320B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L,...
1832823
PUMP AS-FUEL PRIMING
120H, 120H NA, 135H, 135H NA, 3114, 3116, 320B, 320D GC, 320D L, 322B L, 322B LN, 322C, 322C FM, 323D L, 324D, 324D L, 324D LN, 325B L, 325C, 325D, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 330...
120H, 120H NA, 135H, 135H NA, 3114, 3116, 320B, 320D GC, 320D L, 322B L, 322B LN, 322C, 322C FM, 323D L, 324D, 324D L, 324D LN, 325B L, 325C, 325D, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 330...
7T8891
PUMP AS-WASHER
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, ...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, ...
1593139
PUMP AS-WATER
3116, 3126, 3126B, 3126E, 322C, 322C FM, 325C, 325C FM, 328D LCR, 329D L, 570B, 580B, 962G II, C7, M325C MH
3116, 3126, 3126B, 3126E, 322C, 322C FM, 325C, 325C FM, 328D LCR, 329D L, 570B, 580B, 962G II, C7, M325C MH
1593145
PUMP AS-WATER
3116, 3126, 3126B, 3126E, 950F, 950F II, 960F, C7
3116, 3126, 3126B, 3126E, 950F, 950F II, 960F, C7
3522142
PUMP AS-WATER
3116, 3126, 3126B, 3126E, C7
3116, 3126, 3126B, 3126E, C7
2364420
PUMP AS-WATER
120K, 12K, 140K, 140K 2, 160K, 3126B, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 328D LCR, 329D, 329D L, 329D LN, 938G II, C7...
120K, 12K, 140K, 140K 2, 160K, 3126B, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 328D LCR, 329D, 329D L, 329D LN, 938G II, C7...
2105559
PUMP AS-GEROTOR
3126, 3126B, 322C, 325C, 325C FM, 543, 580B, 938G II, 950G II, 962G II, IT38G II
3126, 3126B, 322C, 325C, 325C FM, 543, 580B, 938G II, 950G II, 962G II, IT38G II
1057573
PUMP GP-FUEL TRANSFER
3408B, 3408C, 3412, 3412C, PM3412, SCT673, SPS342, SPT342
3408B, 3408C, 3412, 3412C, PM3412, SCT673, SPS342, SPT342
6N7527
PUMP AS-FUEL INJECTION
1673C, 215, 225, 3208, 3304, 3306, 518, 613B, 920, 941, CS-551, D4D, D4E, D5, D6C, D6D, D7F, PS-500
1673C, 215, 225, 3208, 3304, 3306, 518, 613B, 920, 941, CS-551, D4D, D4E, D5, D6C, D6D, D7F, PS-500
1491950
PUMP GP-FUEL TRANSFER
24H, 3408E, 3412E, 5110B, 631D, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 69D, 769C, 769D, 771D, 773B, 773D, 773E, 775B, 775D, 775E, 834B, 836, 844, 988B, 988F II, 990, 990 II, 992C, AD40, AD45, AE...
24H, 3408E, 3412E, 5110B, 631D, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 69D, 769C, 769D, 771D, 773B, 773D, 773E, 775B, 775D, 775E, 834B, 836, 844, 988B, 988F II, 990, 990 II, 992C, AD40, AD45, AE...
1329447
PUMP AS-FUEL TRANSFER
3056, AP-1200
3056, AP-1200
1003717
PUMP AS-ENGINE OIL
3056, 924G, 924GZ, CS-663E, CS-683E
3056, 924G, 924GZ, CS-663E, CS-683E
1935170
PUMP GP-SUMP
3034, 3054, 3054B, 3056, C1.5, C2.2
3034, 3054, 3054B, 3056, C1.5, C2.2
1734050
PUMP GP-UNIT INJECTOR HYD
3126B, C7
3126B, C7