1707499 PUMP GP-FUEL INJECTION Caterpillar parts
236, 248, 267, 287, 3034
Rating:
Alternative (cross code) number:
CA1707499
170-7499
1707499
CA1707499
170-7499
1707499
Weight: 4 pounds 1 kg.
MARINE ENGINE, SKID STEER LOADER,
This part in 5 request:
Show.
This information for suppliers only!
2022-07-21
2022-03-16
2021-08-26
2018-03-02
2017-05-08
Compatible equipment models: 1707499:
Number on catalog scheme:
21
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 452-6006 Grease Cartridge 1
C 4C-9485 Pin Driver Cap 1 Note: Make sure that the pin bores in the stick and in the boom are thoroughly clean and free of dirt and debris prior to the installation of the stick on the boom.
Put a thin coat of Tooling (B) on the sleeve bearings and on the lips of lip seals.
Start the machine. Raise the boom. Swing the boom over the stick. Align the pin bores for the boom to stick pin.
Illustration 1 g06315586
Typical Example.
Illustration 2 g06315588
Typical Example.
(B) Boom. (S) Stick.
Install a shim (8) on each side of the boom between the boom and the stick at the pin bore. Shim (8) is identified by the tab on the shim. Install Tooling (C) into pin assembly (6). Attach a suitable lifting device to pin assembly (6). The weight of pin assembly (6) is approximately 28 kg (62 lb).
Force the stick to one side of the boom. Measure the total clearance between the stick and the boom. Install the required shims.
Use Tooling (C) and a suitable hammer to install pin assembly (6).
Measure the total clearance between the stick and the boom at the pin bore. The total clearance is Dimension (X) plus Dimension (Y). The total clearance must not be more than 1.6 mm (0.063 inch). If the total clearance is less than 1.6 mm (0.063 inch), the addition of shims will not be necessary. If the total clearance is more than 1.6 mm (0.063 inch), the addition of shims will be required.
If shims are required, remove pin assembly (6). Install the required amount of shims (9) and (10) between the stick and the boom on the side opposite retaining bolt (5). Locate shims (9) and (10) between the boom and shim (8). Install pin assembly (6).
Install the washer and retaining bolt (5).
Illustration 3 g06315591
Install new O-ring seals in the ends of hose assemblies (4) Connect all hose assemblies (4) in the original location.
Illustration 4 g06315590
Typical Example.
Fasten a suitable lifting device to the rod end of stick cylinder (1). Use machine hydraulics to extend stick cylinder (1) until the pin bore lines up with the pin bores in the stick. Install a shim on each side of the stick cylinder at the pin bore.
Install the spacer and pin assembly (2). Install the washer and retaining bolt (3).End By:
Install the bucket.
Table 1
Required Tools
Tool Part Number Part Description Qty
B 452-6006 Grease Cartridge 1
C 4C-9485 Pin Driver Cap 1 Note: Make sure that the pin bores in the stick and in the boom are thoroughly clean and free of dirt and debris prior to the installation of the stick on the boom.
Put a thin coat of Tooling (B) on the sleeve bearings and on the lips of lip seals.
Start the machine. Raise the boom. Swing the boom over the stick. Align the pin bores for the boom to stick pin.
Illustration 1 g06315586
Typical Example.
Illustration 2 g06315588
Typical Example.
(B) Boom. (S) Stick.
Install a shim (8) on each side of the boom between the boom and the stick at the pin bore. Shim (8) is identified by the tab on the shim. Install Tooling (C) into pin assembly (6). Attach a suitable lifting device to pin assembly (6). The weight of pin assembly (6) is approximately 28 kg (62 lb).
Force the stick to one side of the boom. Measure the total clearance between the stick and the boom. Install the required shims.
Use Tooling (C) and a suitable hammer to install pin assembly (6).
Measure the total clearance between the stick and the boom at the pin bore. The total clearance is Dimension (X) plus Dimension (Y). The total clearance must not be more than 1.6 mm (0.063 inch). If the total clearance is less than 1.6 mm (0.063 inch), the addition of shims will not be necessary. If the total clearance is more than 1.6 mm (0.063 inch), the addition of shims will be required.
If shims are required, remove pin assembly (6). Install the required amount of shims (9) and (10) between the stick and the boom on the side opposite retaining bolt (5). Locate shims (9) and (10) between the boom and shim (8). Install pin assembly (6).
Install the washer and retaining bolt (5).
Illustration 3 g06315591
Install new O-ring seals in the ends of hose assemblies (4) Connect all hose assemblies (4) in the original location.
Illustration 4 g06315590
Typical Example.
Fasten a suitable lifting device to the rod end of stick cylinder (1). Use machine hydraulics to extend stick cylinder (1) until the pin bore lines up with the pin bores in the stick. Install a shim on each side of the stick cylinder at the pin bore.
Install the spacer and pin assembly (2). Install the washer and retaining bolt (3).End By:
Install the bucket.
Caterpillar parts catalog:
Parts pump Caterpillar catalog:
236, 236B, 267, 287
216, 236, 3034, 906
216, 236, 247, 248, 267, 287, 3034, 906
216, 228, 236, 247, 267, 3034, 906
216, 228, 236, 247, 248, 267, 287, 3034, 906
2335719
PUMP GP-DIAPHRAGM
216, 216B, 226B, 228, 232B, 236, 236B, 242B, 246C, 247, 247B, 248, 252B, 256C, 257B, 262C, 267, 267B, 268B, 272C, 277C, 279C, 287, 287C, 289C, 297C, 299C
216, 216B, 226B, 228, 232B, 236, 236B, 242B, 246C, 247, 247B, 248, 252B, 256C, 257B, 262C, 267, 267B, 268B, 272C, 277C, 279C, 287, 287C, 289C, 297C, 299C
236, 248, 267, 287
1935170
PUMP GP-SUMP
3034, 3054, 3054B, 3056, C1.5, C2.2
3034, 3054, 3054B, 3056, C1.5, C2.2
1473041
PUMP GP
3034, 906
3034, 906
236, 248, 267, 287
3054B, 312B L, 416C, 416D, 420D, 426C, 428C, 428D, 432D, 436C, 438C, 438D, 442D, 908, AP-800C, BG-225B, CB-434C, CB-534C, CB-535B, CP-433C, CP-433E, CS-423E, CS-431C, PS-300B
2335719
PUMP GP-DIAPHRAGM
216, 216B, 226B, 228, 232B, 236, 236B, 242B, 246C, 247, 247B, 248, 252B, 256C, 257B, 262C, 267, 267B, 268B, 272C, 277C, 279C, 287, 287C, 289C, 297C, 299C
216, 216B, 226B, 228, 232B, 236, 236B, 242B, 246C, 247, 247B, 248, 252B, 256C, 257B, 262C, 267, 267B, 268B, 272C, 277C, 279C, 287, 287C, 289C, 297C, 299C
1428918
PUMP GP-PISTON
216, 228
216, 228
216, 216B, 242B, 247B, 3013, 3013C, 3014, 3024, 3024C, C1.5, C2.2, CB-334D, CB-335D
216, 228, 236, 247, 248, 267, 287, 3034, 906
3406E, 572R II, 633E II, C-12, C-15, C-16, C15, D7R II, MTC835, R1600, R1700G
324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 328D LCR, 329D L, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 584, 627G, 637D, 637G, 81...
12H, 140M, 140M 2, 160M, 160M 2, 2290, 2390, 330C, 330C L, 330D, 330D FM, 330D L, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 552, 552 ...
12H, 140M, 160M, 2290, 2390, 2391, 2491, 2590, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 511, 521, 522, 532, 541, 551, 552, 627G, 637D, 637E, 637G...