1754806 PUMP & MOTOR GP-FUEL TRANSFER Caterpillar parts
307, D6R, D6R II
Rating:
Alternative (cross code) number:
CA1754806
175-4806
1754806
CA1754806
175-4806
1754806
Weight: 9 pounds 4 kg.
EXCAVATOR, TRACK-TYPE TRACTOR,
Related part:
1754806
PUMP GP-ELEC
0R7876
R
Number on catalog scheme:
8
For full view, you need register
Information:
Removal Procedure
Start By:
Remove the mounting bracket for the Electronic Control Module (ECM) . Refer to Disassembly and Assembly, "ECM Mounting Bracket- Remove and Install" for the correct procedure.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the cooling system into a suitable container. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
Illustration 1 g02193293
If the engine has a left-hand side oil filter, remove the oil filter base. Refer to Disassembly and Assembly, "Oil Filter Base - Remove and Install" for the correct procedure.
Disconnect plastic tube assembly (1) from crankcase breather (2) and remove the plastic tube assembly from the clips. Refer to Disassembly and Assembly, "Crankcase Breather- Remove" for the correct procedure.
Disconnect plastic tube assembly (5) from crankcase breather canister (2) and crankcase breather valve (8). Refer to Disassembly and Assembly, "Crankcase Breather- Remove" for the correct procedure.
Cut the cable straps for engine wiring harness (3) that secure the wiring harness assembly to engine oil cooler (6).
Remove bolt (4) and remove bracket (7) from engine oil cooler (6). Position the bracket away from the engine oil cooler
Remove bolt (10) from the bracket for the tube assembly. Loosen nut (9) and remove tube assembly.
Remove seal (11) (not shown) from the tube assembly.
Illustration 2 g02194313
Remove bolt (12) from bracket (13). Position bracket (13) away from the engine oil cooler.
Remove bolts (14) from oil cooler (6). Note: The bolts are different lengths. Note the position of the different bolts. Note the location and the orientation of the brackets for the tube assemblies.
Remove engine oil cooler assembly (6) from the cylinder block.
Remove gasket (15) (not shown).
Illustration 3 g02193294
If necessary, follow Step 13.a through Step 13.c in order to disassemble the engine oil cooler.
Remove nuts (18) from the assembly of engine oil cooler (6).
Remove cooler matrix (16) from housing (19).
Remove gaskets (17).
Start By:
Remove the mounting bracket for the Electronic Control Module (ECM) . Refer to Disassembly and Assembly, "ECM Mounting Bracket- Remove and Install" for the correct procedure.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the cooling system into a suitable container. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
Illustration 1 g02193293
If the engine has a left-hand side oil filter, remove the oil filter base. Refer to Disassembly and Assembly, "Oil Filter Base - Remove and Install" for the correct procedure.
Disconnect plastic tube assembly (1) from crankcase breather (2) and remove the plastic tube assembly from the clips. Refer to Disassembly and Assembly, "Crankcase Breather- Remove" for the correct procedure.
Disconnect plastic tube assembly (5) from crankcase breather canister (2) and crankcase breather valve (8). Refer to Disassembly and Assembly, "Crankcase Breather- Remove" for the correct procedure.
Cut the cable straps for engine wiring harness (3) that secure the wiring harness assembly to engine oil cooler (6).
Remove bolt (4) and remove bracket (7) from engine oil cooler (6). Position the bracket away from the engine oil cooler
Remove bolt (10) from the bracket for the tube assembly. Loosen nut (9) and remove tube assembly.
Remove seal (11) (not shown) from the tube assembly.
Illustration 2 g02194313
Remove bolt (12) from bracket (13). Position bracket (13) away from the engine oil cooler.
Remove bolts (14) from oil cooler (6). Note: The bolts are different lengths. Note the position of the different bolts. Note the location and the orientation of the brackets for the tube assemblies.
Remove engine oil cooler assembly (6) from the cylinder block.
Remove gasket (15) (not shown).
Illustration 3 g02193294
If necessary, follow Step 13.a through Step 13.c in order to disassemble the engine oil cooler.
Remove nuts (18) from the assembly of engine oil cooler (6).
Remove cooler matrix (16) from housing (19).
Remove gaskets (17).
Caterpillar parts catalog:
Parts pump Caterpillar catalog:
3054, 307, 312, 315, 317, 416B, 416C, 426C, 428B, 428C, 436C, 438C, 914G, AP-800C, BG-225B, CB-434B, CB-544, CB-545, IT14G, TH62, TH63, TH82, TH83
12G, 12H, 12H ES, 12H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 235B, 330, 330 FM L, 330 L, 3306, 3306B, 3306C, 330B, 330B L, 350, 545, 572R, 611, 615C, 627...
D6R, D6R II, D6R III
120G, 12G, 12H, 12H ES, 12H NA, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 214B, 235, 3114, 3116, 3126, 3126B, 3126E, 3176, 3176B, 3176C, 3196,...
120G, 12G, 130G, 140G, 140H, 143H, 14G, 14H, 160G, 160H, 163H, 1673C, 16H, 235B, 24H, 3116, 311C, 311D LRR, 3126, 3126B, 3126E, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315C, 315D L,...
3054, 3054B, 307, 416B, 416C, 416D, 424D, 428B, 428C, CB-434B, CB-434C, CB-544, CB-545, CP-433C, CS-323C, CS-431C, PS-150B, TH210, TH215, TH62, TH63, TH82
3054, 3054B, 307, 312, 312C, 315, 315B L, 317, 416B, 416C, 426C, 428B, 428C, 436C, 438C, 914G, AP-800C, BG-225B, CB-434B, CB-434C, CB-534B, CB-534C, CB-544, CB-545, CP-433C, CS-323C, CS-431C, IT14G, M...
12H, 140M, 160M, 2290, 2390, 2391, 2491, 2590, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 511, 521, 522, 532, 541, 551, 552, 627G, 637D, 637E, 637G...
12H, 140M, 140M 2, 160M, 160M 2, 2290, 2390, 330C, 330C L, 330D, 330D FM, 330D L, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 552, 552 ...
324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 328D LCR, 329D L, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 584, 627G, 637D, 637G, 81...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, ...
D6H, D6H XL, D6H XR, D6R
1272230
PUMP GP-FUEL INJECTION
M312, M315
M312, M315
M312, M315, M318, M320
311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN, 318B, 320 L
1478500
PUMP GP-AUXILIARY GEAR
312, 312B L, 315B L
312, 312B L, 315B L
6C5572
PUMP & MOTOR GP-REFUELING
307, 312, 315, 317, 320 L, 322, 322 LN, 325, 325 L, 325 LN, 330 FM L, 330 L, 350, D6M
307, 312, 315, 317, 320 L, 322, 322 LN, 325, 325 L, 325 LN, 330 FM L, 330 L, 350, D6M
1262078
PUMP GP-GEAR
311B, 311C, 312B, 314C, 315B FM L, 317B LN, 318B
311B, 311C, 312B, 314C, 315B FM L, 317B LN, 318B
307, 307B, 308C, 315, 315B, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G, E120, E140, E70, E70B
315, 315B, 315C, 317B LN, 318B, D3C III, D3G, D4C III, D4G, D5C III, D5G
312C, 315B L, 554, M312, M315
1090, 1190, 1190T, 1290T, 307B, 312B L, 312C, 315B L, 315C, 317B LN, 318B, 318C, 320B, D6M, M313C, M313D, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318C, M318C MH, M318D, M318D MH, M322C, M322D, ...