PUMP & MTG GP-UNIT INJ HYD 1832859 - Caterpillar

Connect hose assembly (34) to tube assembly (48), with one o-ring seal (95).
Connect other end of hose assembly (34) to elbow assembly (68), as shown in Illustration 40.
Using three clips (101), three bolts (105), and three hard washers (103), secure hose assembly (34) onto three weld bosses (77).441-9453 Hose As
Illustration 41 g06334260
Right view - inside left frame (engine end)
(20) 148-8327 Connector As
(55) 441-9453 Hose As
(68) 148-8392 Elbow As
Connect one end of hose assembly (55) to elbow assembly (68) at the pump.
Connect other end of hose assembly (55) to connector assembly (20) on the axle oil cooler group for the front axle.389-4376 Hose As
Illustration 42 g06340218
Right view - inside left frame (engine end)
(36) 389-4376 Hose As
(37) 477-2993 Hose As
(49) 441-9442 Tube As
(65) 148-8355 Elbow As
(73) 200-6345 Mounting Saddle
(79) 430-5329 Boss
(80) 4D-7388 Clip
(83) 204-2281 Cable Strap
(86) 5K-9090 O-Ring Seal
(103) 8T-4121 Hard Washer
(112) 8T-4196 Bolt
(136) 397-9301 Hard Washer (11.5X20X15-MM THK)
Using one o-ring seal (86), connect one end of hose assembly (36) to tube assembly (49).
Connect the other end of hose assembly (36) to elbow assembly (65) at the pump.
Using one hard washer (136), one clip (80), one bolt (112), and one hard washer (103), secure hose assembly (36) to previously installed boss (79).Axle Oil Cooler Lines Securing Hardware
Illustration 43 g06334262
Right view - inside left frame (engine end)
(35) 389-4263 Hose As
(37) 477-2993 Hose As
(54) 441-9452 Hose As
(55) 441-9453 Hose As
(56) 149-7738 Clip
(58) 101-3129 Stud
(73) 200-6345 Mounting Saddle
(76) 344-5675 Nut
(77) 388-5576 Weld Boss (30-MM)
(83) 204-2281 Cable Strap
(85) 483-2517 Clip
(99) 7X-7729 Washer
(103) 8T-4121 Hard Washer
(112) 8T-4196 Bolt
Using one mounting saddle (73) and two cable straps (83), secure hose assembly (54) and hose assembly (55), to hose assembly (37).
Remove one clip (85), two washers (99) and one nut (76) from stud (58) (previously installed in Step 30 of "Pump Group" in "Installation of Rear Frame Components"). Install clip (85) onto hose assembly (54) and hose assembly (55) and secure onto stud (58) using two washers (99) and one nut (76).
Using two clips (56), one bolt (112), two hard washers (103), and one nut (76), secure hose assembly (55) to hose assembly (35)
Illustration 44 g06345408
Left side view
(55) 441-9453 Hose As
(73) 200-6345 Mounting Saddle
(83) 204-2281 Cable Strap
(G) Exhaust fluid lines
Using two cable straps (83) and one mounting saddle (73), secure exhaust fluid lines (G) to hose assembly (55).Note: All machines are not equipped with exhaust fluid lines (G).Enabling Axle Oil Cooler System
Note: This feature can be configured and must be activated with Product Software Programming System (PSPS) or a service tool.
Use Cat® Electronic Technician (Cat ET) Service Tool and select the proper Electronic Control Module (ECM) . Select "SERVICE" from the menu.
Select "CONFIGURATION" from the menu.
Double-click the desired feature on the configuration screen.
Select the desired status of the feature and click "OK". The feature will be activated on the next power cycle.
Start the machine and bring hydraulic up to temperature.
Check all the connections for fluid leaks.Note: If leaks are found shut down the machine, recheck the connection for tightness, and restart the machine.Note: Be