AVSPARE.COM
parts catalog

PUMP GP-PISTON 1991063 - Caterpillar


1991063 PUMP GP-PISTON Caterpillar parts D3G, D4G, D5G
Rating:
39
Alternative (cross code) number:
CA1991063
199-1063
1991063
Caterpillar 1991063 PUMP GP-PISTON
Weight: 92 pounds 41 kg.

Buy PUMP GP-PISTON 1991063 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 1991063:

TRACK-TYPE TRACTOR  D3G   D4G   D5G   Caterpillar
Number on catalog scheme: 2
  For full view, you need register

Information:


Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01124853Transmission oil filter housing (2) is located on the top left side of the transmission case at the left rear of the tractor.
Park the machine on level ground. Apply the parking brake.
Lower the bowl to the ground. Stop the engine.
Clean the transmission oil filter housing.
Remove drain plug (3). Allow the oil to drain into a suitable container.
Remove bolts (1) from the transmission oil filter housing. Remove the cover from the transmission oil filter housing.
Remove the used filter element and discard the used filter element.
Clean the inside of the transmission oil filter housing with a clean towel.
Insert a new filter element into the transmission oil filter housing.
Inspect the seal for the transmission oil filter housing. Replace the seal if the seal is damaged.
Install the cover on the transmission oil filter housing. Install the bolts on the transmission oil filter housing.
Install the drain plug in the transmission oil filter housing.
Illustration 2 g01124854The magnetic screen is located below the transmission oil filter at the rear of the transmission housing.
Remove drain plug (6). Drain the oil into a suitable container.
Remove bolts (4).
Remove cover (5).
Remove the magnetic screen.
Separate the magnets from the magnetic screen. Wash the magnetic screen and the magnets in a nonflammable solvent. Note: Do not rap the magnets on hard objects. The magnets may be damaged. Replace any damaged magnets.
Allow the cleaned parts to dry. Use compressed air in order to speed the drying of the parts.
Clean the magnets with a towel or clean the magnets with a stiff bristle brush.
Install the magnets into the magnetic screen.
Install the magnetic screen into the transmission housing.
Install the cover and the bolts.
Install the drain plug.
Add transmission oil. Maintain the oil level between the "FULL" mark and the "ADD" mark on the transmission sight gauge. Refer to Operation and Maintenance Manual, "Transmission Oil Level - Check" for the proper procedure.
Start the engine. Run the engine at low idle.
Check the transmission oil filter for leaks. Check the magnetic screen for leaks.
Check the oil level of the transmission. Add oil, if necessary.
Stop the engine.

Caterpillar parts catalog:

Caterpillar parts catalog
D3G XL & LGP TRACK TYPE TRACTORS CFC00001-UP (MACHINE) POWERED BY 3046 Engine
D4G XL & LGP TRACK TYPE TRACTORS CFN00001-01071 (MACHINE) POWERED BY 3046 Engine
D5G XL & LGP TRACK TYPE TRACTORS FDH00001-UP (MACHINE) POWERED BY 3046 Engine


Parts pump Caterpillar catalog:

1371296 PUMP GP-GEAR
D3C III, D3G, D4C III, D4G, D5C III, D5G
1166724 PUMP GP-WATER
315, 315B, 315B FM L, 315C, 317B LN, 318B, D3C III, D3G, D4C III, D4G, D5C III, D5G
1282931 PUMP AS-FUEL INJECTION
933, 933C, D3C III, D3G, D5G
1296259 PUMP GP-FUEL PRIMING
216, 216B, 216B3, 226B, 226B3, 232B, 242B, 247B, 247B3, 257B, 301.5, 302.5, 303.5, 304.5, 3116, 45, 527, 55, 554, 574, 902, 924F, 928F, 928G, 938F, 938G, 950F, 950F II, 950G, 960F, 962G, BG-225C, CB-1...
2044944 PUMP GP-UNIT INJECTOR HYD
3126E, 627G, 637G, 973C, C-9, C9, D6R II, MTC735
1210196 PUMP & MTG GP-HYDRAULIC
RM-250C, RR-250, RR-250B, SS-250
8F2184 PUMP
D320A, D326F, D330A, D330B, D333A, D333B, D337, D337F, D364, D375D, D397D
2624960 PUMP GP-FUEL PRIMING
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B
1597574 PUMP GP-FUEL PRM & PRIM FILTER
AP-1000B, AP-1055B, AP-900B, BG-2455C, BG-245C
2354535 PUMP GP-WATER
793D, 797, 797B, G3516C, G3516E, G3520C, G3520E
1401203 PUMP GP-PISTON
CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-634C
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.