PUMP 2346783 - Caterpillar

2346783 PUMP Caterpillar parts

Price: query

Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2346783
234-6783
2346783

Buy PUMP 2346783 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices:

As an associate, we earn commssions on qualifying purchases through the links below

Kumho Solus TA51a All Season 235/55R20 102V Passenger Tire

$194.88

11 Sep 2024
30.0[13.50] pounds
Amazon.com

Kumho Solus TA51a All Season 235/55R20 102V Passenger Tire
Kumho Designed for use on passenger cars such as coupes, sedans, CUVs, SUVs, and minivans || Backed by a 65,000 mile limited manufacturer tread life on sizes with an H-speed rating and above, and a 75,000 mile limited manufacturer tread life on T-speed rated sizes || Specialized tread compound with multi-functionalized polymers and high dispersion silica extend tread life and maximize grip || Ribs and grooves along the tread break up and dissipate road noise for a quieter ride || Four wide circumferential grooves maximize water drainage to resist hydroplaning

For full view, you need register

Information:

Illustration 2 g00939746
Use a screwdriver to remove retaining ring (3) and plug (2) at each end of the steering link (4).
Illustration 3 g00939909
Install Tooling (A) to hold the ball stud (5) while the locknut (6) is being loosened.
Illustration 4 g00939917
Use Tooling (B) to remove locknut (6). Remove locknut (6).
Illustration 5 g06201465
Illustration 6 g06201511
Use Tooling (C) to remove ball stud (5). Refer to M0080743 Tool Operating Manual , "Hammer Group" and , M0083627 , "Hydraulic Power Unit" Tool Operating Manual for the correct procedure to remove the ball stud. Repeat the step for the remaining steering link ball studs.
Use Tooling (D) to support the steering link. The weight of the steering link is approximately 120 kg (265 lb).
Remove the steering link .
Repeat Step 1 through 7 to remove the opposite steering link.Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 176-6538 Spanner Wrench As 1
B Socket (89.3 mm) 1
132-8119 Hydraulic Torque Wrench 1
132-8223 Hydraulic Pump and Motor Gp (115V) 1
132-8231(1) Hydraulic Pump (220V) 1
D 509-9680 Adapter 1
509-9679 Component Handler 1
E 4C-5593 Anti-Seize Compound -
(1) Available SubstituteNote: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Verify that all the components are clean and free of foreign material prior to installation. Inspect all components for wear and replace the components, if necessary.
Inspect all components for wear and replace the components, if necessary.
Apply Tooling (E) to the threads of ball stud (5) and on taper of ball stud.
Use Tooling (D) to support the steering link. The weight of the steering link is approximately 120 kg (265 lb).
Install the steering link.
Illustration 7 g00943956
Install locknut (6) on ball stud (5), as shown.
Repeat Step 6 for the ball stud on the opposite end of steering link (4).
Install Tooling (A) to hold the ball stud while the locknut is being tightened.
Illustration 8 g00943887
Use Tooling (B) to install locknut (6). Tighten the locknut to a torque of 2550 100 N m (1884 74 lb ft).
Illustration 9 g00943997
Install plug (2) and retaining ring (3) onto the ball stud. Use a soft hammer to seat the retaining ring.
Illustration 10 g00944031
Connect lubrication hose (1) to the plug (2).
Repeat Steps 8 through 11 to complete installation of steering link (4).
Repeat Steps 1 through 12 to install the opposite steering link.
After the steering links are installed, check the front wheel alignment. Refer to Systems Operation/Testing and Adjusting, "Steering System" for the correct procedure.