2408381 PUMP AS-FUEL Caterpillar parts
301.6C, 302.5C, 303.5C, 303C CR, 304C CR, 305C CR
Rating:
Alternative (cross code) number:
CA2408381
240-8381
2408381
CA2408381
240-8381
2408381
Weight: 0.66 pounds 0 kg.
MINI HYD EXCAVATOR,
You can buy:
US$32.00
28 May 2025
FridayParts
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
1G63952034 Fuel Feed Pump 12V For Engine 11922552102 28033000 2408381(White plug 12V)
GKOKG Easy to install, but still recommended to be operated by professionals. || manufacturing ensuring maximum durability, not easy to damage, with good performance and long service life. || This Product Are Tested Before Shipping || Every product has quality inspection before leaving the factory. || Strong impact resistance and durability: adopts scientific structure design, the antistrike ability is strong.
GKOKG Easy to install, but still recommended to be operated by professionals. || manufacturing ensuring maximum durability, not easy to damage, with good performance and long service life. || This Product Are Tested Before Shipping || Every product has quality inspection before leaving the factory. || Strong impact resistance and durability: adopts scientific structure design, the antistrike ability is strong.
Fuel Pump 240-8381 CA2408381 2408381 For Caterpillar CAT 301.6C 302.5C 303.5C 303C CR 304C CR 305C CR
Generic For Caterpillar For CAT 301.6C 302.5C 303.5C 303C CR 304C CR 305C CR
Generic For Caterpillar For CAT 301.6C 302.5C 303.5C 303C CR 304C CR 305C CR
Texxparts 12V Fuel Pump 240-8381 2408381 Compatible with Ford New Holland Tractor 100 Compatible with Hitachi Mini Excavator ZX30U-2
Texxparts Part Numbers: 240-8381 2408381 485510011 GN-23167 SBA485510011 MNP-115304 MNP-485510011 23167GT 115304 || Compatible with Ford New Holland Tractor 100 400C 400D Compatible with Hitachi Mini Excavator ZX30U-2 ZX35U-2 Compatible with Caterpillar Mini Hydraulic Excavator 301.6C 302.5C 303.5C 303C CR 304C CR 305C CR Compatible with Perkins Engine 402D-05 402C-05 403D-11 403C-07 403C-11 403C-15 403D-07 403D-15 403D-15T 404D-15 404D-22 404D-22T 404C-20 404C-22 404C-22T 102.04 103.06 103.10 103.15 104.19 103.12 104.22 103.11 || Package Includes: 1 x Fuel Pump || Condition: High Quality, Well Packed Strict Quality Control to Ensure High Performance || Replacement Parts. Premium Quality - Reliable in Operation,Long Working Life
Texxparts Part Numbers: 240-8381 2408381 485510011 GN-23167 SBA485510011 MNP-115304 MNP-485510011 23167GT 115304 || Compatible with Ford New Holland Tractor 100 400C 400D Compatible with Hitachi Mini Excavator ZX30U-2 ZX35U-2 Compatible with Caterpillar Mini Hydraulic Excavator 301.6C 302.5C 303.5C 303C CR 304C CR 305C CR Compatible with Perkins Engine 402D-05 402C-05 403D-11 403C-07 403C-11 403C-15 403D-07 403D-15 403D-15T 404D-15 404D-22 404D-22T 404C-20 404C-22 404C-22T 102.04 103.06 103.10 103.15 104.19 103.12 104.22 103.11 || Package Includes: 1 x Fuel Pump || Condition: High Quality, Well Packed Strict Quality Control to Ensure High Performance || Replacement Parts. Premium Quality - Reliable in Operation,Long Working Life
Number on catalog scheme:
4
For full view, you need register
Compatible equipment models: 2408381:
Information:
System Operation Description:Use this procedure to troubleshoot any suspect problems with the digital sensor supply.Use this procedure for the following diagnostic codes:
041-03 8 Volt DC Supply short to +batt
041-04 8 Volt DC Supply short to ground
535-08 Exhaust Temperature Sensor noisy signalThe digital sensor supply provides a regulated voltage of 8.0 0.4 VDC to the exhaust temperature sensor. The digital sensor supply is output short circuit protected. A short circuit to the battery should not cause permanent damage to the circuit inside the Electronic Control Module (ECM). The exhaust temperature sensor is not protected from overvoltage.
Illustration 1 g01057424
Illustration 2 g01057423
P1 ECM connector
(P1-4) 8 V digital supply
(P1-5) Digital return
(P1-68) Exhaust temperature sensor Test Step 1. Inspect Electrical Connectors and Wiring
Turn the Engine Control Switch (ECS) to the OFF/RESET position.
Thoroughly inspect the J1/P1 ECM connector and the J2/P2 ECM connector. Thoroughly inspect the connectors for each analog sensor. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the sensor connectors that are associated with the active diagnostic code.
Check the ECM connector (allen head screw) for the proper torque of 6.0 N m (55 lb in).
Check the harness and wiring for abrasions and for pinch points from the sensors back to the ECM. Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and/or of pinch points.Results:
OK - There are no problems with the wiring and/or the connectors. Proceed to Test Step 2.
Not OK - Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check for Active Diagnostic Codes
Connect the electronic service tool to the service tool connector.
Turn the ECS to the COOLDOWN/STOP position.
Monitor the active diagnostic code screen on the electronic
041-03 8 Volt DC Supply short to +batt
041-04 8 Volt DC Supply short to ground
535-08 Exhaust Temperature Sensor noisy signalThe digital sensor supply provides a regulated voltage of 8.0 0.4 VDC to the exhaust temperature sensor. The digital sensor supply is output short circuit protected. A short circuit to the battery should not cause permanent damage to the circuit inside the Electronic Control Module (ECM). The exhaust temperature sensor is not protected from overvoltage.
Illustration 1 g01057424
Illustration 2 g01057423
P1 ECM connector
(P1-4) 8 V digital supply
(P1-5) Digital return
(P1-68) Exhaust temperature sensor Test Step 1. Inspect Electrical Connectors and Wiring
Turn the Engine Control Switch (ECS) to the OFF/RESET position.
Thoroughly inspect the J1/P1 ECM connector and the J2/P2 ECM connector. Thoroughly inspect the connectors for each analog sensor. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the sensor connectors that are associated with the active diagnostic code.
Check the ECM connector (allen head screw) for the proper torque of 6.0 N m (55 lb in).
Check the harness and wiring for abrasions and for pinch points from the sensors back to the ECM. Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and/or of pinch points.Results:
OK - There are no problems with the wiring and/or the connectors. Proceed to Test Step 2.
Not OK - Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check for Active Diagnostic Codes
Connect the electronic service tool to the service tool connector.
Turn the ECS to the COOLDOWN/STOP position.
Monitor the active diagnostic code screen on the electronic
Caterpillar parts catalog:
Parts pump Caterpillar catalog:
301.6C
303.5C, 303.5D, 303C CR, 304C CR, 304D CR, 305.5D, 305C CR, 305D CR, 904B, 904H
303.5C, 303.5D, 303C CR, 304C CR, 304D CR, 305.5D, 305C CR, 305D CR
302.5C
301.6C
3224956
PUMP-WASHER
301.6C, 302.5C, 308E2 CR, 906H2, 907H2, 908H2, D3G, D4G, D5G
301.6C, 302.5C, 308E2 CR, 906H2, 907H2, 908H2, D3G, D4G, D5G
302.5C
2833164
PUMP AS-ENGINE OIL
303.5C
303.5C
2706239
PUMP AS-OIL
303.5C, 904B, 904H
303.5C, 904B, 904H
2828594
PUMP AS-FUEL INJECTION
304C CR, 305D CR
304C CR, 305D CR
305.5D, 305C CR
301.6C
3154537
PUMP AS
303.5C, 303.5D, 304C CR, 304D CR, 305C CR, 305D CR
303.5C, 303.5D, 304C CR, 304D CR, 305C CR, 305D CR
3036502
PUMP AS
304D CR
304D CR
2195247
PUMP GP
304
304
2833164
PUMP AS-ENGINE OIL
303.5C
303.5C
302.5C
3224956
PUMP-WASHER
301.6C, 302.5C, 308E2 CR, 906H2, 907H2, 908H2, D3G, D4G, D5G
301.6C, 302.5C, 308E2 CR, 906H2, 907H2, 908H2, D3G, D4G, D5G