2418686 PUMP GP-TRANSMISSION Caterpillar parts
966H, 972H
Rating:
Alternative (cross code) number:
CA2418686
241-8686
2418686
CA2418686
241-8686
2418686
Weight: 84 pounds 38 kg.
WHEEL LOADER,
Related part:
2418686
PUMP GP-GR 1
20R6493
R
This part in 5 request:
Show.
This information for suppliers only!
2024-12-05
2024-09-26
2022-10-03
2022-06-22
2017-03-27
Information:
Which Generate This Code:This diagnostic code is recorded when the second output driver in the MSS ECM is shorted to ground. This circuit is not used on all machines. Check for the presence of wires at contact 5 and contact 52 before you perform the procedure.The possible causes of this diagnostic code are listed below:
The wiring in the machine harness has failed.
The driven component in the circuit has failed.
The ECM has failed. This is unlikely.Test Step 1. CHECK THE WIRING HARNESS.
Disconnect the wiring harness connector from the MSS ECM.
Measure the resistance between pin 18 in the wiring harness and a ground on the machine.Expected Result:The resistance is greater than 5000 Ohms.Results:
YES - The resistance is greater than 5000 Ohms (no continuity). Harness circuit resistance is correct. Proceed to Test Step 3.
NO - Resistance is less than 5000 Ohms (continuity). The machine harness is faulty. There is a short between frame ground and the machine harness. The driven component in the circuit may also be bad. Proceed to Test Step 2.Test Step 2. CHECK THE COMPONENT.
Trace the harness to the driven component in the circuit. The component will be a relay. The component may also be a solenoid.
Measure the resistance of the component. Measure the resistance from each terminal to the case of the component.Expected Result:The resistance is greater than 5000 Ohms.Results:
YES - The resistance of the driven component is greater than 5000 Ohms (no continuity). The component is good. The machine harness has failed. There is a short between frame ground and the machine harness.Repair: Check the harness for signs of damage. Repair the machine harness or replace the machine harness. Stop.
NO - Resistance is less than 5000 Ohms (continuity). The driven component has failed. Repair: Replace the component that has failed. Stop.Test Step 3. CHECK IF THE DIAGNOSTIC CODE IS STILL ACTIVE.
Remove the connector from the ECM. Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the key start switch to the ON position.
Clear all inactive diagnostic codes.
Operate the machine.
Determine if CID 1392 FMI 04 is present.Expected Result:CID 1392 FMI 04 is present.Results:
YES - CID 1392 FMI 04 is present.Repair: The problem has not been corrected. It is unlikely that the ECM has failed. Perform the previous Steps again. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace". Stop.
NO - CID 1392 FMI 04 is not present.Repair: The diagnostic code is NOT present. The problem does not exist at this time. The initial problem was probably caused by an intermittent short in the wiring harness. Inspect the harness for any signs of damage. If the harness passes through a hole with a grommet, that area of the harness can become chafed. This may cause an intermittent short. The harness may also be damaged in locations that could pinch the harness. Repair any wiring that could have caused the problem. Resume normal machine operation. Stop.
The wiring in the machine harness has failed.
The driven component in the circuit has failed.
The ECM has failed. This is unlikely.Test Step 1. CHECK THE WIRING HARNESS.
Disconnect the wiring harness connector from the MSS ECM.
Measure the resistance between pin 18 in the wiring harness and a ground on the machine.Expected Result:The resistance is greater than 5000 Ohms.Results:
YES - The resistance is greater than 5000 Ohms (no continuity). Harness circuit resistance is correct. Proceed to Test Step 3.
NO - Resistance is less than 5000 Ohms (continuity). The machine harness is faulty. There is a short between frame ground and the machine harness. The driven component in the circuit may also be bad. Proceed to Test Step 2.Test Step 2. CHECK THE COMPONENT.
Trace the harness to the driven component in the circuit. The component will be a relay. The component may also be a solenoid.
Measure the resistance of the component. Measure the resistance from each terminal to the case of the component.Expected Result:The resistance is greater than 5000 Ohms.Results:
YES - The resistance of the driven component is greater than 5000 Ohms (no continuity). The component is good. The machine harness has failed. There is a short between frame ground and the machine harness.Repair: Check the harness for signs of damage. Repair the machine harness or replace the machine harness. Stop.
NO - Resistance is less than 5000 Ohms (continuity). The driven component has failed. Repair: Replace the component that has failed. Stop.Test Step 3. CHECK IF THE DIAGNOSTIC CODE IS STILL ACTIVE.
Remove the connector from the ECM. Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the key start switch to the ON position.
Clear all inactive diagnostic codes.
Operate the machine.
Determine if CID 1392 FMI 04 is present.Expected Result:CID 1392 FMI 04 is present.Results:
YES - CID 1392 FMI 04 is present.Repair: The problem has not been corrected. It is unlikely that the ECM has failed. Perform the previous Steps again. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace". Stop.
NO - CID 1392 FMI 04 is not present.Repair: The diagnostic code is NOT present. The problem does not exist at this time. The initial problem was probably caused by an intermittent short in the wiring harness. Inspect the harness for any signs of damage. If the harness passes through a hole with a grommet, that area of the harness can become chafed. This may cause an intermittent short. The harness may also be damaged in locations that could pinch the harness. Repair any wiring that could have caused the problem. Resume normal machine operation. Stop.
Caterpillar SIS machinery equipment:
Caterpillar SIS
966H Wheel Loader Military RWE00001-UP (MACHINE) POWERED BY C11 Engine »
241-8686
PUMP GP-TRANSMISSION
966H Wheel Loader A6D00001-UP (MACHINE) POWERED BY C11 Engine »
241-8686
PUMP GP-TRANSMISSION
972H Wheel Loader A7D00001-UP (MACHINE) POWERED BY C13 Engine »
241-8686
PUMP GP-TRANSMISSION
966H Wheel Loader A6G00001-UP (MACHINE) POWERED BY C11 Engine »
241-8686
PUMP GP-TRANSMISSION
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine »
241-8686
PUMP GP-TRANSMISSION
966H Wheel Loader Military FMW00001-UP (MACHINE) POWERED BY C11 Engine »
241-8686
PUMP GP-TRANSMISSION
972H Wheel Loader-Military WLA00001-UP (MACHINE) POWERED BY C13 Engine »
241-8686
PUMP GP-TRANSMISSION
966H Wheel Loader TAL00001-UP (MACHINE) POWERED BY C11 Engine »
241-8686
PUMP GP-TRANSMISSION
972H Wheel Loader GTA00001-UP (MACHINE) POWERED BY C13 Engine »
241-8686
PUMP GP-TRANSMISSION
966H Wheel Loader RYF00001-UP (MACHINE) POWERED BY C11 Engine »
241-8686
PUMP GP-TRANSMISSION
972H Wheel Loader LCC00001-UP (MACHINE) POWERED BY C13 Engine »
241-8686
PUMP GP-TRANSMISSION
966H Wheel Loader BJ600001-UP (MACHINE) POWERED BY C11 Engine »
241-8686
PUMP GP-TRANSMISSION
972H Wheel Loader WXZ00001-UP (MACHINE) POWERED BY C13 Engine »
241-8686
PUMP GP-TRANSMISSION
966H Wheel Loader BS600001-UP (MACHINE) POWERED BY C11 Engine »
241-8686
PUMP GP-TRANSMISSION
972H Wheel Loader NPE00001-UP (MACHINE) POWERED BY C13 Engine »
241-8686
PUMP GP-TRANSMISSION
966H WHEEL LOADER A6J01801-UP (MACHINE) POWERED BY C11 »
241-8686
GEAR PUMP GROUP
972H WHEEL LOADER A7J00501-UP (MACHINE) POWERED BY C13 »
241-8686
GEAR PUMP GROUP
966H WHEEL LOADER A6J00001-01800 (MACHINE) POWERED BY C11 ENGINE »
241-8686
GEAR PUMP GROUP
972H WHEEL LOADER A7J00001-00500 (MACHINE) POWERED BY C13 ENGINE »
241-8686
GEAR PUMP GROUP
Caterpillar parts catalog:
Parts pump Caterpillar catalog:
1908977
PUMP GP-FUEL PRM & WATER SEP
120H, 120K, 120K 2, 12H, 12K, 135H, 140K, 140K 2, 140M, 14M, 160K, 160M, 16M, 24M, 3126B, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 3...
120H, 120K, 120K 2, 12H, 12K, 135H, 140K, 140K 2, 140M, 14M, 160K, 160M, 16M, 24M, 3126B, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 3...
3520205
PUMP GP-WATER
14M, 16M, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 621H, 621K, 623H, 623K LRC, 627H, 627K LRC, 725, 730, 730C, 966H, 972H, 980C, 980K, 980K HLG, C11, C13, C13 XQ350, CX31-C13I, D8...
14M, 16M, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 621H, 621K, 623H, 623K LRC, 627H, 627K LRC, 725, 730, 730C, 966H, 972H, 980C, 980K, 980K HLG, C11, C13, C13 XQ350, CX31-C13I, D8...
3520206
PUMP GP-WATER
14M, 16M, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 725, 730, 966H, 972H, 980C, C11, C13, CX31-C13I, D8N, R1600H, R1700G, RM-300, TH35-C11I, W345C MH
14M, 16M, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 725, 730, 966H, 972H, 980C, C11, C13, CX31-C13I, D8N, R1600H, R1700G, RM-300, TH35-C11I, W345C MH
2285811
PUMP GP-WATER
14M, 16M, 345C, 345C L, 345C MH, 345D L, 725, 730, 966H, 972H, C11, C13, CX31-C13I, R1700G, RM-300, TH35-C13I, W345C MH
14M, 16M, 345C, 345C L, 345C MH, 345D L, 725, 730, 966H, 972H, C11, C13, CX31-C13I, R1700G, RM-300, TH35-C13I, W345C MH
2335220
PUMP GP-ENGINE OIL
140H, 143H, 14H, 14M, 160H, 163H, 16H, 16M, 3176, 3176B, 3176C, 3196, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 365B, 365B II, 365B L, 572R II, 6...
140H, 143H, 14H, 14M, 160H, 163H, 16H, 16M, 3176, 3176B, 3176C, 3196, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 365B, 365B II, 365B L, 572R II, 6...
2545147
PUMP GP-PISTON
966H, 972H
966H, 972H
3848611
PUMP GP-FUEL TRANSFER
16M, 3406E, 572R II, 621H, 621K, 623H, 623K LRC, 627H, 627K LRC, 631D, 631E, 631G, 637D, 637E, 637G, 730C, 966H, 972H, 980C, C-12, C-15, C-16, C-18, C13, C15, C16, C18, D7R II, D8N, R2900G, R3000H
16M, 3406E, 572R II, 621H, 621K, 623H, 623K LRC, 627H, 627K LRC, 631D, 631E, 631G, 637D, 637E, 637G, 730C, 966H, 972H, 980C, C-12, C-15, C-16, C-18, C13, C15, C16, C18, D7R II, D8N, R2900G, R3000H
1908970
PUMP GP-FUEL PRIMING
120H, 120K, 120K 2, 12H, 12K, 135H, 140K, 140K 2, 140M, 14M, 160K, 160M, 16M, 24M, 3126B, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 3...
120H, 120K, 120K 2, 12H, 12K, 135H, 140K, 140K 2, 140M, 14M, 160K, 160M, 16M, 24M, 3126B, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 3...
2304176
PUMP GP-METERING
950G II, 950H, 962G II, 962H, 966G II, 966H, 972G II, 972H, 988H, IT62G II, IT62H
950G II, 950H, 962G II, 962H, 966G II, 966H, 972G II, 972H, 988H, IT62G II, IT62H
2313946
PUMP GP-FUEL TRANSFER
16M, 631D, 631E, 631G, 633E II, 637E, 637G, 966H, 972H, C-15, C-16, C-18, C15, C16, D8N, TH35-C15T
16M, 631D, 631E, 631G, 633E II, 637E, 637G, 966H, 972H, C-15, C-16, C-18, C15, C16, D8N, TH35-C15T
2959259
PUMP GP-FUEL TRANSFER
16M, 345D L, 572R II, 966H, 972H, C-12, C13, D7R II, MTC835
16M, 345D L, 572R II, 966H, 972H, C-12, C13, D7R II, MTC835
3166863
PUMP GP-FUEL TRANSFER
966H, D7R II, MTC835, R2900, R2900G
966H, D7R II, MTC835, R2900, R2900G
6L5856
PUMP GP-WATER
3408, 3412, 3412D, 3412E, D342, D342C, D343, D353C
3408, 3412, 3412D, 3412E, D342, D342C, D343, D353C
3327928
PUMP GP-FUEL TRANSFER
3508B, 3508C
3508B, 3508C
8J4516
PUMP GP-GEAR
910, G910
910, G910
2541417
PUMP GP-FUEL INJECTION
3508C, 3512C
3508C, 3512C
1U2824
PUMP GP-VANE
613C, 613C II
613C, 613C II
3228594
PUMP GP-AUXILIARY SEA WATER
3412E, C32
3412E, C32
3607392
PUMP GP-GEAR
621H, 623H, 627H
621H, 623H, 627H
1049832
PUMP & METER GP
RR-250, SS-250
RR-250, SS-250