2497347 PUMP GP-FUEL INJECTION Caterpillar parts
236B, 246C, 252B, 267B, 3044C
Rating:
Alternative (cross code) number:
CA2497347
249-7347
2497347
CA2497347
249-7347
2497347
INDUSTRIAL ENGINE, SKID STEER LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Diesel VE4 Fuel Injection Pump Compatible with Caterpillar CAT 3044C Engine Skid Steers Loader 236B 246B 246C 252B 262B 267B 277B 287B 196000-5020 32A65-37030 249-7346 2497347
KBBYT Part Numbers: 196000-5020 249-7346 2467346 249-7347 2497347 32A65-37030 32A6537030 VE4-R502 VE4-RND502 VE4/12F1300RND502 || Part Name: Fuel Injection Pump || Application: For Caterpillar Skid Steers Loader 236B 246B 246C 252B 262B 267B 277B 287B Warm reminder: kindly verify your part numbers before proceeding with your purchase. In case of any uncertainty, feel free to provide us with your engine model or pump part number for assistance. || Service: We can handle all customs clearance procedures and pay import taxes/duties on your behalf, ensuring you receive your package conveniently and quickly. || Notice: Please confirm your part number and compare product images before purchasing to avoid unnecessary returns.If you are not sure that the pump is suitable for your vehicle, please send us email with your vehicle engine model and fuel pump part number
KBBYT Part Numbers: 196000-5020 249-7346 2467346 249-7347 2497347 32A65-37030 32A6537030 VE4-R502 VE4-RND502 VE4/12F1300RND502 || Part Name: Fuel Injection Pump || Application: For Caterpillar Skid Steers Loader 236B 246B 246C 252B 262B 267B 277B 287B Warm reminder: kindly verify your part numbers before proceeding with your purchase. In case of any uncertainty, feel free to provide us with your engine model or pump part number for assistance. || Service: We can handle all customs clearance procedures and pay import taxes/duties on your behalf, ensuring you receive your package conveniently and quickly. || Notice: Please confirm your part number and compare product images before purchasing to avoid unnecessary returns.If you are not sure that the pump is suitable for your vehicle, please send us email with your vehicle engine model and fuel pump part number
IMELBUFF 196000-5020 32A65-37030 249-7346 2497347 VE Fuel Injection Pump for Caterpillar 3044C Engine 236B 246B 246C 252B 262B 267B 277B 287B Skid Steers Loader
IMELBUFF ????Part Number: 196000-5020 249-7346 2467346 249-7347 2497347 32A65-37030 32A6537030 VE4-R502 VE4-RND502 VE4/12F1300RND502 || ????Engine Model: for Caterpillar Engine 3044C || ????Vehicle Application: for Caterpillar Skid Steers Loader 236B 246B 246C 252B 262B 267B 277B 287B || ????Warm Tips: please check your part numbers before placing an order. If you are not sure, you can send us your engine model or pump part number. || ????Service: 5-months warranty and 24 hour support for customer service. Please feel free to contact us by email if you have any question with the product
IMELBUFF ????Part Number: 196000-5020 249-7346 2467346 249-7347 2497347 32A65-37030 32A6537030 VE4-R502 VE4-RND502 VE4/12F1300RND502 || ????Engine Model: for Caterpillar Engine 3044C || ????Vehicle Application: for Caterpillar Skid Steers Loader 236B 246B 246C 252B 262B 267B 277B 287B || ????Warm Tips: please check your part numbers before placing an order. If you are not sure, you can send us your engine model or pump part number. || ????Service: 5-months warranty and 24 hour support for customer service. Please feel free to contact us by email if you have any question with the product
VE Fuel Injection Pump Compatible with Caterpillar 3044C Engine 236B 246B 246C 252B 262B 267B 277B 287B Skid Steers Loader 196000-5020 32A65-37030 249-7346 2497347
KBBYT Part Number： 196000-5020 249-7346 2467346 249-7347 2497347 32A65-37030 32A6537030 VE4-R502 VE4-RND502 VE4/12F1300RND502 || Application：For Caterpillar Engine 3044C || Application for use with Caterpillar Skid Steers Loader models 236B, 246B, 246C, 252B, 262B, 267B, 277B, and 287B. || Friendly reminder: Please verify your part numbers prior to making a purchase. If you are uncertain, feel free to provide us with either your engine model or pump part number for assistance. || Service: We offer a 5-month warranty on all products and provide round-the-clock customer support. If you have any questions about our products, please don't hesitate to contact us via email.
KBBYT Part Number： 196000-5020 249-7346 2467346 249-7347 2497347 32A65-37030 32A6537030 VE4-R502 VE4-RND502 VE4/12F1300RND502 || Application：For Caterpillar Engine 3044C || Application for use with Caterpillar Skid Steers Loader models 236B, 246B, 246C, 252B, 262B, 267B, 277B, and 287B. || Friendly reminder: Please verify your part numbers prior to making a purchase. If you are uncertain, feel free to provide us with either your engine model or pump part number for assistance. || Service: We offer a 5-month warranty on all products and provide round-the-clock customer support. If you have any questions about our products, please don't hesitate to contact us via email.
Number on catalog scheme:
For full view, you need register
Compatible equipment models: 2497347:
Information:
MID 039 - Machine Control Module CID 3458 - Autonomous Steering Enable Valve Displacement Sensor FMI 04 - Voltage Below Normal
Illustration 1 g03814403This diagnostic code is recorded when the Input/Output Module (I/O Module) reads the voltage from the "SEL Valve Spool Pos" as being below normal or shorted to ground.Test Step 1. CHECK THE SENSOR.
Turn the disconnect switch and the keyswitch to the ON position.
Ensure that the diagnostic code is active.
Observe the status of the diagnostic code. Disconnect the machine harness from the sensor. Expected Result:The diagnostic code will remain active if the sensor is not the cause of the diagnostic code. The sensor is the cause of the diagnostic code if the diagnostic code is NO longer active.Results:
OK - The diagnostic code remains active. The sensor has NOT failed. The machine harness may have failed or the I/O Module may have failed. Proceed to Test Step 2.
NOT OK - The diagnostic code is NO longer active. The machine harness and the I/O Module are operating properly.Repair: The sensor has failed. Replace the sensor.STOPTest Step 2. CHECK THE CIRCUIT FOR A SHORT TO GROUND.
The sensor remains disconnected from the machine harness.
Turn the keyswitch and the disconnect switch to the OFF position.
Disconnect the machine harness connector J1 from the I/O Module.
At the machine harness connector J1, measure the resistance from contact 36 (wire U736-YL(Yellow)) to all possible sources of ground. Expected Result:The resistance should be greater than 5000 ohms.Results:
OK - The resistance is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - The resistance is less than 5000 ohms. There is a short in the machine harness.Repair: The short is between the circuits with the low resistance measurement. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Clean the contacts of the harness connectors.
Reconnect all harness connectors.
Observe the status of the diagnostic code.
Operate the machine.
Observe the status of the diagnostic code. Expected Result:The diagnostic code is NO longer active.Results:
YES - The diagnostic code is NO longer active. The diagnostic code does not exist at this time. The initial diagnostic code was probably caused by a poor electrical connection and/or a short at one of the harness connectors that was disconnected and then reconnected. Resume normal machine operationSTOP
NO - The diagnostic code has not been corrected. The ECM has failed.Repair: It is unlikely that the I/O Module has failed. Exit this procedure and perform this diagnostic code procedure again. Replace the I/O Module if the cause of the diagnostic code is not found. Prior to replacing an I/O Module, always contact your dealership's Technical Communicator for possible consultation with Caterpillar. This consultation may greatly reduce repair time. Refer to Testing and Adjusting, KENR8394, "Electronic Control Module (ECM) - Replace".STOP
Illustration 1 g03814403This diagnostic code is recorded when the Input/Output Module (I/O Module) reads the voltage from the "SEL Valve Spool Pos" as being below normal or shorted to ground.Test Step 1. CHECK THE SENSOR.
Turn the disconnect switch and the keyswitch to the ON position.
Ensure that the diagnostic code is active.
Observe the status of the diagnostic code. Disconnect the machine harness from the sensor. Expected Result:The diagnostic code will remain active if the sensor is not the cause of the diagnostic code. The sensor is the cause of the diagnostic code if the diagnostic code is NO longer active.Results:
OK - The diagnostic code remains active. The sensor has NOT failed. The machine harness may have failed or the I/O Module may have failed. Proceed to Test Step 2.
NOT OK - The diagnostic code is NO longer active. The machine harness and the I/O Module are operating properly.Repair: The sensor has failed. Replace the sensor.STOPTest Step 2. CHECK THE CIRCUIT FOR A SHORT TO GROUND.
The sensor remains disconnected from the machine harness.
Turn the keyswitch and the disconnect switch to the OFF position.
Disconnect the machine harness connector J1 from the I/O Module.
At the machine harness connector J1, measure the resistance from contact 36 (wire U736-YL(Yellow)) to all possible sources of ground. Expected Result:The resistance should be greater than 5000 ohms.Results:
OK - The resistance is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - The resistance is less than 5000 ohms. There is a short in the machine harness.Repair: The short is between the circuits with the low resistance measurement. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Clean the contacts of the harness connectors.
Reconnect all harness connectors.
Observe the status of the diagnostic code.
Operate the machine.
Observe the status of the diagnostic code. Expected Result:The diagnostic code is NO longer active.Results:
YES - The diagnostic code is NO longer active. The diagnostic code does not exist at this time. The initial diagnostic code was probably caused by a poor electrical connection and/or a short at one of the harness connectors that was disconnected and then reconnected. Resume normal machine operationSTOP
NO - The diagnostic code has not been corrected. The ECM has failed.Repair: It is unlikely that the I/O Module has failed. Exit this procedure and perform this diagnostic code procedure again. Replace the I/O Module if the cause of the diagnostic code is not found. Prior to replacing an I/O Module, always contact your dealership's Technical Communicator for possible consultation with Caterpillar. This consultation may greatly reduce repair time. Refer to Testing and Adjusting, KENR8394, "Electronic Control Module (ECM) - Replace".STOP
Caterpillar SIS machinery equipment:
Caterpillar SIS
3044C Industrial Engine 34400001-UP »
249-7347
PUMP GP-FUEL INJECTION
236B 246B 252B 262B SKID STEER LOADER HEN00001-06749 (MACHINE) POWERED BY 3044C Engine »
249-7347
PUMP GP-FUEL INJECTION
236B 246B 252B 262B SKID STEER LOADER HEN00001-06749 (MACHINE) POWERED BY 3044C Engine »
249-7347
PUMP GP-FUEL INJECTION
267B, 277B and 287B Multi Terrain Loader CYC00001-UP (MACHINE) POWERED BY 3044C Engine »
249-7347
PUMP GP-FUEL INJECTION
267B, 277B and 287B Multi Terrain Loader CYC00001-UP (MACHINE) POWERED BY 3044C Engine »
249-7347
PUMP GP-FUEL INJECTION
246C Skid Steer Loader JAY00001-UP (MACHINE) POWERED BY 3044C Engine »
249-7347
PUMP GP-FUEL INJECTION
236B2 Skid Steer Loader HEN06750-UP (MACHINE) POWERED BY 3044C Engine »
249-7347
PUMP GP-FUEL INJECTION
252B2 Skid Steer Loader SCP04600-UP (MACHINE) POWERED BY 3044C Engine »
249-7347
PUMP GP-FUEL INJECTION
Caterpillar parts catalog:
Parts pump Caterpillar catalog:
236, 236B, 267, 287
236B3, 242B3, 246C, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 267B, 268B, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 906, 906H, 907H, 908, 908H, C3.4
3044C, 906, 906H, 907H, C3.4
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 267B, 268B, 272C, 277C, 277C2, 279C2, 287C, 287C2, 289C2, 297C, 299C, 3044C, 906, 906H, 907H, 908, 908H, C3.4
3044C
236B, 236B3, 242B3, 252B, 252B3, 257B3, 259B3, 267B, CW-34
3044C, C3.4
3044C, C3.4
246C, 256C, 262C, 262C2, 277C, 279C, 287C, 289C
3044C, 933, 933C, 939, 939C, D3C III, D4C III, D5C III
2468308
PUMP AS-FUEL INJECTION
3044C, 906, 906H, 907H
3044C, 906, 906H, 907H
3044C, C3.4
966H, 972H
16M, 345D L, 572R II, 966H, 972H, C-12, C13, D7R II, MTC835
16M, 631D, 631E, 631G, 633E II, 637E, 637G, 966H, 972H, C-15, C-16, C-18, C15, C16, D8N, TH35-C15T
3000724
PUMP GP-FUEL PRM & PRIM FILTER
3044C, C3.4
3044C, C3.4
2996948
PUMP GP-FUEL PRM & PRIM FILTER
3044C, C3.4
3044C, C3.4
3317333
PUMP GP-FUEL INJECTION
3044C, 908H, C3.4
3044C, 908H, C3.4
3013391
PUMP GP-FUEL INJECTION
3044C, 906, 906H, 907H
3044C, 906, 906H, 907H