2847730 PUMP GP-GEAR Caterpillar parts
773F, 775F
Rating:
Alternative (cross code) number:
CA2847730
284-7730
2847730
CA2847730
284-7730
2847730
Weight: 125 pounds 56 kg.
TRUCK,
Information:
Typical Pump
1. Bolts (4) 2. Cover 3. Screws (2) 4. Pin 5. Inlet Support Plate 6. Seal Packs 7. Flex Plates 8. Rotor 9. Vanes 10. Inserts 11. Ring 12. Outlet Support Plate 13. O-ring Seals 14. Seal ring 15. Back-up Ring 16. Lock Ring 17. Retaining Ring 18. Bearing 19. Shaft 20. Key 21. Spacer Washer 22. Primary Seal 23. Secondary Seal 24. Body Disassembly
1. Remove the pump from the machine. Put an alignment mark (A) on the pump body and cover for reference during assembly. After removal of the cartridge, put an alignment mark (B) across the outer surface of the cartridge parts for reference during assembly.2. Put the cartridge on a flat surface with outlet support plate (1) down, and remove two Allen head screws (2). Remove inlet support plate (3). CAUTION: Do not slide flex plates (4) and (5) across ring (6) or rotor (7). Burrs on the ring or rotor can cause deep scratches in the bronze surface of the flex plates. Lift inlet flex plate (4) off the rotor and ring.3. Put a small flat piece of wood on the rotor and ring. Hold the parts together and turn the cartridge over. CAUTION: Do not let ring (6) slide across flex plate (5). Remove outlet support plate (1). Lift outlet flex plate (5) off the rotor and ring. Keep flex plates (4) and (5) with their respective support plates.4. Remove ring (6) from rotor (7). Find the location of arrow (C) on the outside diameter of rotor (7). Remove vanes (8) and inserts (9) in sequence starting at arrow (C). Keep the vanes and inserts in order for correct assembly.Assembly
1. Clean all parts thoroughly. Remove all O-rings, back-up rings and seal packs; do not use these parts again.2. Score marks less than .001" (0.025) deep and scratches less than .002" (0.051) deep can be removed with a fine oil stone. CAUTION: Use of a dry stone on the bronze surfaces of the flex plates will cause scratches.3. Use a fine oil stone to remove any burrs from the edges of the cartridge parts.4. If the location pins were removed from the inlet support plate, use a soft hammer to install new pins with the grooves inside of the inlet support plate.5. Put the inlet and outlet support plates on a flat surface. Install seal packs (1) in the cavities of the plates with the O-rings down. Put flex plates (2) and (3) in position on their respective support plates with the bronze surface up. Put the alignment marks on the plates in alignment.6. Put rotor (4) on a flat wooden board with arrow (A) toward the direction of rotation (toward the right for clockwise rotation or toward the left for counterclockwise rotation). Install vanes (5) and inserts (6) in their respective positions in the rotor. Make sure the sharp edge of each
1. Bolts (4) 2. Cover 3. Screws (2) 4. Pin 5. Inlet Support Plate 6. Seal Packs 7. Flex Plates 8. Rotor 9. Vanes 10. Inserts 11. Ring 12. Outlet Support Plate 13. O-ring Seals 14. Seal ring 15. Back-up Ring 16. Lock Ring 17. Retaining Ring 18. Bearing 19. Shaft 20. Key 21. Spacer Washer 22. Primary Seal 23. Secondary Seal 24. Body Disassembly
1. Remove the pump from the machine. Put an alignment mark (A) on the pump body and cover for reference during assembly. After removal of the cartridge, put an alignment mark (B) across the outer surface of the cartridge parts for reference during assembly.2. Put the cartridge on a flat surface with outlet support plate (1) down, and remove two Allen head screws (2). Remove inlet support plate (3). CAUTION: Do not slide flex plates (4) and (5) across ring (6) or rotor (7). Burrs on the ring or rotor can cause deep scratches in the bronze surface of the flex plates. Lift inlet flex plate (4) off the rotor and ring.3. Put a small flat piece of wood on the rotor and ring. Hold the parts together and turn the cartridge over. CAUTION: Do not let ring (6) slide across flex plate (5). Remove outlet support plate (1). Lift outlet flex plate (5) off the rotor and ring. Keep flex plates (4) and (5) with their respective support plates.4. Remove ring (6) from rotor (7). Find the location of arrow (C) on the outside diameter of rotor (7). Remove vanes (8) and inserts (9) in sequence starting at arrow (C). Keep the vanes and inserts in order for correct assembly.Assembly
1. Clean all parts thoroughly. Remove all O-rings, back-up rings and seal packs; do not use these parts again.2. Score marks less than .001" (0.025) deep and scratches less than .002" (0.051) deep can be removed with a fine oil stone. CAUTION: Use of a dry stone on the bronze surfaces of the flex plates will cause scratches.3. Use a fine oil stone to remove any burrs from the edges of the cartridge parts.4. If the location pins were removed from the inlet support plate, use a soft hammer to install new pins with the grooves inside of the inlet support plate.5. Put the inlet and outlet support plates on a flat surface. Install seal packs (1) in the cavities of the plates with the O-rings down. Put flex plates (2) and (3) in position on their respective support plates with the bronze surface up. Put the alignment marks on the plates in alignment.6. Put rotor (4) on a flat wooden board with arrow (A) toward the direction of rotation (toward the right for clockwise rotation or toward the left for counterclockwise rotation). Install vanes (5) and inserts (6) in their respective positions in the rotor. Make sure the sharp edge of each
Caterpillar SIS machinery equipment:
Caterpillar SIS
773F Off-Highway Truck EED00001-UP (MACHINE) POWERED BY C27 Engine »
284-7730
PUMP GP-GEAR
775F Off-Highway Truck DLS00001-UP (MACHINE) POWERED BY C27 Engine »
284-7730
PUMP GP-GEAR
773F OEM Off-Highway Truck EXD00001-UP (MACHINE) POWERED BY C27 Engine »
284-7730
PUMP GP-GEAR
775F OEM Off-Highway Truck EYG00001-UP (MACHINE) POWERED BY C27 Engine »
284-7730
PUMP GP-GEAR
Caterpillar parts catalog:
Parts pump Caterpillar catalog:
4N5837
PUMP GP-WATER
24H, 3412, 3412C, 3412D, 3412E, 5110B, 651E, 657E, 772B, 773B, 773D, 773E, 773F, 775B, 775D, 775E, 775F, 844, 844H, 990, 990 II, 990H, 992C, 992D, AD55B, AD60, C27, C30, C32, CG137-12, CX35-P800, D10N...
24H, 3412, 3412C, 3412D, 3412E, 5110B, 651E, 657E, 772B, 773B, 773D, 773E, 773F, 775B, 775D, 775E, 775F, 844, 844H, 990, 990 II, 990H, 992C, 992D, AD55B, AD60, C27, C30, C32, CG137-12, CX35-P800, D10N...
1908977
PUMP GP-FUEL PRM & WATER SEP
120H, 120K, 120K 2, 12H, 12K, 135H, 140K, 140K 2, 140M, 14M, 160K, 160M, 16M, 24M, 3126B, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 3...
120H, 120K, 120K 2, 12H, 12K, 135H, 140K, 140K 2, 140M, 14M, 160K, 160M, 16M, 24M, 3126B, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 3...
1161980
PUMP GP-ENGINE OIL
24H, 3408E, 3412C, 3412E, 631D, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 69D, 769C, 769D, 771D, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, ...
24H, 3408E, 3412C, 3412E, 631D, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 69D, 769C, 769D, 771D, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, ...
2191964
PUMP GP-PISTON
769D, 770, 771D, 772, 773D, 773E, 773F, 775D, 775E, 775F
769D, 770, 771D, 772, 773D, 773E, 773F, 775D, 775E, 775F
3520200
PUMP GP-WATER
3412, 3412C, 3412D, 3412E, 5110B, 651E, 657E, 773B, 773D, 773E, 773F, 775B, 775D, 775E, 775F, 844, 844H, 990, 990 II, 990H, 992C, AD55B, AD60, C27, C32, CG137-12, CX35-P800, D10N, D10R, D8L, D9L, D9N,...
3412, 3412C, 3412D, 3412E, 5110B, 651E, 657E, 773B, 773D, 773E, 773F, 775B, 775D, 775E, 775F, 844, 844H, 990, 990 II, 990H, 992C, AD55B, AD60, C27, C32, CG137-12, CX35-P800, D10N, D10R, D8L, D9L, D9N,...
1116841
PUMP GP-GEAR
69D, 769D, 771D, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM
69D, 769D, 771D, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM
1908970
PUMP GP-FUEL PRIMING
120H, 120K, 120K 2, 12H, 12K, 135H, 140K, 140K 2, 140M, 14M, 160K, 160M, 16M, 24M, 3126B, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 3...
120H, 120K, 120K 2, 12H, 12K, 135H, 140K, 140K 2, 140M, 14M, 160K, 160M, 16M, 24M, 3126B, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 3...
1371339
PUMP GP-WATER
24H, 3412, 3412C, 3412D, 3412E, 5110B, 651E, 657E, 773B, 773D, 773E, 773F, 775D, 775E, 775F, 844, 844H, 990, 990 II, 990H, 992C, 992D, C27, C30, C32, D10N, D10R, D8L, D9L, D9N, D9R, G3412, G3412C, PM3...
24H, 3412, 3412C, 3412D, 3412E, 5110B, 651E, 657E, 773B, 773D, 773E, 773F, 775D, 775E, 775F, 844, 844H, 990, 990 II, 990H, 992C, 992D, C27, C30, C32, D10N, D10R, D8L, D9L, D9N, D9R, G3412, G3412C, PM3...
2280007
PUMP & LINES GP
773F, 775F
773F, 775F
2847731
PUMP GP-GEAR
773F, 775F
773F, 775F
2624980
PUMP GP-PISTON
773F, 775F
773F, 775F
7T8890
PUMP AS WASHER
120M, 120M 2, 12M, 140M, 140M 2, 14M, 160M, 160M 2, 16M, 215B, 215C, 215D, 219D, 225, 225D, 227, 229, 229D, 231D, 235B, 235C, 235D, 245, 245B, 245D, 311B, 311D LRR, 312, 312B L, 312C L, 312D, 312D L, ...
120M, 120M 2, 12M, 140M, 140M 2, 14M, 160M, 160M 2, 16M, 215B, 215C, 215D, 219D, 225, 225D, 227, 229, 229D, 231D, 235B, 235C, 235D, 245, 245B, 245D, 311B, 311D LRR, 312, 312B L, 312C L, 312D, 312D L, ...
1312652
PUMP GP-GOV & FUEL INJ
3306, 3306B
3306, 3306B
2373960
PUMP GP-GEAR
773F, 775F
773F, 775F
2321835
PUMP GP-PISTON
784C, 785C, 785D
784C, 785C, 785D
3G7610
PUMP GP-GEAR
834B, 988B
834B, 988B
4448536
PUMP GP-PISTON
D6T LGPPAT
D6T LGPPAT
1375597
PUMP GP-FUEL PRM & SEC FILTER
3406E, C-15, C-16
3406E, C-15, C-16