PUMP GP-CHARGE 2935441 - Caterpillar

Install harness and connectors to the rear of the cab as shown.
Illustration 6 g06130285
Close-up of area B
(GE-C9) Connect to Stick-In Control Pressure Sensor, "997 OR", "993 BR", "M814 BR"
(GE-C5) Connect to Stick-In Solenoid, "P943 GY", "J809 BR"
(GE-C7) Connect to Boom-Down Solenoid, "K762 BU", "M739 YL", (with yellow tape)
( 2) 7K-1181 Cable Strap
(5) 503-7139 Chassis Harness As
(7) 132-5789 Clip
(10) 8T-4121 Hard Washer
(11) 8T-4191 Bolt
Route and connect harness (5) to the pressure sensor and the solenoids as shown.
Illustration 7 g06130317
Close-up of area C
(GE-M1) Connect to ground, "235 BK"
(2) 7K-1181 Cable Strap
(5) 503-7139 Chassis Harness As
Route harness (5) and connect ground wire as shown.
Illustration 8 g06130833
Close-up of area D.
(1) 3S-2093 Cable Strap
(2) 7K-1181 Cable Strap
(5) 503-7139 Chassis Harness As
(8) 5P-4295 Cable StrapNote: In the above illustration, each cable strap (1) group consists of three cable straps. One cable strap secures chassis harness assembly (5) to the machine harness. One cable strap secures the chassis harness to one side of the link. One cable strap secures the chassis harness to both sides of the link.
Illustration 9 g06130773
Close-up of area D, view to boom connector
(GE-C3) Connect to harness (6 poles), "K833 PK", "K834 PU", "M906 BU", "T800 OR", "G969 YL", "Y947 BR"
(2) 7K-1181 Cable Strap
(5) 503-7139 Chassis Harness As
Route harness (5) as shown.
Illustration 10 g06130895
Close-up of area E
(GE-C20) Connect to Stem "1" Extend Solenoid, "K849 YL", "J808 BK", (with yellow tape)
( GE-C22) Connect to Stem "2" Extend Solenoid, "K850 BR", "J808 BK"
(GE-C16) Connect to Stem "1" Retract Solenoid, "P978 GN", "J808 BK", (with yellow tape)
( GE-C18) Connect to Stem "2" Retract Solenoid, "P979 YL", "J808 BK"
(1) 3S-2093 Cable Strap
(2) 7K-1181 Cable Strap
(4) 266-7379 Cable Strap
(5) 503-7139 Chassis Harness As
(7) 132-5789 Clip
Connect harness (5) to solenoids as shown.
Illustration 11 g06130901
Close-up of area F
(GE-C14) Connect to Boom-Down Electrical Check Solenoid, "X785 BU", "235 BK"
(1) 3S-2093 Cable Strap
(2) 7K-1181 Cable Strap
(5) 503-7139 Chassis Harness As
Route harness (5) and connect as shown.Note: The above illustration is for a machine fitted with a Smart Boom. If Smart Boom is not installed, position connector"GE-C14" to (H) and secure.
Illustration 12 g06131303
Close-up of area G, shown with a Smart Boom installed
(GE-C4) Connect to Harness (6 poles), "997 OR", "235 BK", "993 BR", "M813 BU", "P702 GY"
(GX-C1) Connect to Harness (6 poles), "997 OR", "235 BK", "993 BR", "M813 BU", "P702 GY"
(GX-C3) Connect to Stick-Out Control Pressure Sensor, "997 OR", "993 BR", "M813 BU"
(GX-C4) Connect to Boom-Up Check Solenoid, "P702 GY", "235 BK"
(1) 3S-2093 Cable Strap
(2) 7K-1181 Cable Strap
(5) 503-7139 Chassis Harness As
(6) 503-7140 Valve Harness As
(7) 132-5789 Clip
(10) 8T-4121 Hard Washer
(11) 8T-4191 Bolt
Route harness (5) and connect to harness (6) as shown. Route harness (6) as shown.Note: The above illustration is for a machine fitted with a Smart Boom. If Smart Boom is not installed, position connector"GX-C4" to (J) and secure.