AVSPARE.COM
parts catalog

PUMP G.-WATER 2H9721 - Caterpillar



2H9721 PUMP G.-WATER Caterpillar parts PUMP
Rating:
46
Alternative (cross code) number:
CA2H9721
2H-9721
2H9721
Caterpillar 2H9721 PUMP G.-WATER
Weight: 1 pounds 0 kg.

Buy PUMP G.-WATER 2H9721 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Table 1
Beeper Configuration    
Event     Description     Pattern    
Above Grade     Audible signal when the bucket is more than one times the vertical tolerance and less than four times the vertical tolerance above grade.     Continuous:
50 msec on
50 msec off    
Avoidance Zone (the machine is within the warning)     Audible signal when the machine is within the warning distance of an avoidance zone or if the "No Avoid" message is displayed. The beeper also sounds in a continuous pattern when the machine is within the avoidance zone.
The beeper tones for the Avoidance zone cannot be disabled.     Once only:
200 msec on
200 msec off
400 msec off    
Below Grade     Audible signal when the bucket is more than one times the vertical tolerance and less than four times the vertical tolerance below grade.     Continuous:
100 msec on
100 msec off    
GPS Accuracy     Audible signal when the GPS accuracy mode changes.     Once only:
200 msec on    
Key/Switch Beeps     Audible signal when a key or a switch is pressed.     Once only:
200 msec on    
On Grade     Audible signal when the bucket is within the vertical tolerance of grade.     Continuous:
On    
Warning Message Appears     Audible signal when a warning message appears and when a warning message automatically disappears.     Once only:
200 msec on
200 msec off
200 msec off    
Warning Message Disappears     Audible signal when a warning message automatically disappears.     Once only:
200 msec on    In order to access the "Beeper" dialog, complete the following steps:
From the "Setup Menu – Configuration" dialog, press the down arrow key or the up arrow key until "Beeper" is highlighted.
Press the "OK" key.The "Beeper" dialog appears. This is shown in Illustration 1.Events that are disabled are identified by a cross in the box. Events that are enabled are identified by a check mark. Events that cannot be disabled are identified by a grayed out check mark. Subevents that cannot be disabled independent of the master event are also identified by a grayed out check mark.
Illustration 1 g01267651
Press the down arrow key or the up arrow key in order to select different events.
Press the "Check mark / Cross" soft key on the display in order to enable or disable an event. Refer to Illustration 1.The different events emit different beeper patterns. To hear the pattern for a particular event, press the "TEST" soft key when the event is selected.
Do one of the following.
Press the "OK" key in order to confirm the setting. The beeper setup is saved. The "Beeper" dialog is closed and the "Setup Menu –Configuration" dialog appears. The changes take effect immediately.
Press the "ESC" key and then press the "OK" key in order to return to the "Setup Menu –Configuration" dialog without saving the changes.
Press the "ESC" key in order to exit the "Setup Menu – Configuration" dialog.


Parts pump Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.