3041618 PUMP GP-PISTON Caterpillar parts
CB-22
Rating:
Alternative (cross code) number:
CA3041618
304-1618
3041618
CA3041618
304-1618
3041618
Weight: 41 pounds 18 kg.
VIBRATORY COMPACTOR,
Compatible equipment models: 3041618:
Number on catalog scheme:
4
For full view, you need register
Information:
Removal Procedure
At operating temperature, the hydraulic tank is hot and under pressure.Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin.Remove the filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. Remove the filler cap slowly in order to relieve pressure.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
To prevent dirt and contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected.This action also lessens the chance of oil spills.
The pressure in the accumulator for the front and rear service brakes must be discharged before the accumulator is removed. Turn the ignition key to the on position. Install a pressure gauge on both pressure test points for the front and the rear brakes. The gauges must read pressure from zero to 20684 kPa (3000 psi). Activate the service brake control valve repeatedly until the pressure in the gauges is at zero. Open the accumulator purge valves in order to verify that all of the pressure has been relieved.
Put identification marks on all lines, hoses, wires, and tubes for installation purposes. Plug all lines, hoses and tubes. This helps prevent fluid loss and contamination of the oil system. Remove the O-ring seal from the hose.
Illustration 1 g00578457
This is a view of the bottom of the brake accumulators.Note: The service brake accumulators are located between the left side of the machine and the transmission.
Open the access door that is directly behind the cab. Disconnect two lines (3) from accumulators (1). Remove four bolts (2) and the hard washers that secure accumulators (1) to the machine frame. Remove the O-ring seals from two lines (3) .
Illustration 2 g00578467
Some components have been removed for photographic clarity.
Remove bolt (5), the hard washer, and bracket (6) that secures accumulators (1) to machine frame (4). Remove the accumulators from the machine.Installation Procedure
Illustration 3 g00578467
Position the accumulators to machine frame (4). Install bolt (5), the hard washer, and bracket (6) that secures accumulators (1) to machine frame (4) .
Illustration 4 g00578457
Install four bolts (2) and the hard washers that secure accumulators (1) to the machine frame. Install the O-ring seals to two lines (3). Connect two lines (3) to accumulators (1) .
Close the access door.
At operating temperature, the hydraulic tank is hot and under pressure.Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin.Remove the filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. Remove the filler cap slowly in order to relieve pressure.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
To prevent dirt and contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected.This action also lessens the chance of oil spills.
The pressure in the accumulator for the front and rear service brakes must be discharged before the accumulator is removed. Turn the ignition key to the on position. Install a pressure gauge on both pressure test points for the front and the rear brakes. The gauges must read pressure from zero to 20684 kPa (3000 psi). Activate the service brake control valve repeatedly until the pressure in the gauges is at zero. Open the accumulator purge valves in order to verify that all of the pressure has been relieved.
Put identification marks on all lines, hoses, wires, and tubes for installation purposes. Plug all lines, hoses and tubes. This helps prevent fluid loss and contamination of the oil system. Remove the O-ring seal from the hose.
Illustration 1 g00578457
This is a view of the bottom of the brake accumulators.Note: The service brake accumulators are located between the left side of the machine and the transmission.
Open the access door that is directly behind the cab. Disconnect two lines (3) from accumulators (1). Remove four bolts (2) and the hard washers that secure accumulators (1) to the machine frame. Remove the O-ring seals from two lines (3) .
Illustration 2 g00578467
Some components have been removed for photographic clarity.
Remove bolt (5), the hard washer, and bracket (6) that secures accumulators (1) to machine frame (4). Remove the accumulators from the machine.Installation Procedure
Illustration 3 g00578467
Position the accumulators to machine frame (4). Install bolt (5), the hard washer, and bracket (6) that secures accumulators (1) to machine frame (4) .
Illustration 4 g00578457
Install four bolts (2) and the hard washers that secure accumulators (1) to the machine frame. Install the O-ring seals to two lines (3). Connect two lines (3) to accumulators (1) .
Close the access door.
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts pump Caterpillar catalog:
3099501
PUMP GP-DIAPHRAGM
CB-14, CB-22, CB-334E, CB-34, CB-44B, CB-54B, CB22B, CB24B, CB32B, CB34B, CB34B XW, CC24B, CC34B, CD-54B, CW-14
CB-14, CB-22, CB-334E, CB-34, CB-44B, CB-54B, CB22B, CB24B, CB32B, CB34B, CB34B XW, CC24B, CC34B, CD-54B, CW-14
3111106
PUMP GP-FUEL INJECTION
3013C, C1.5, C2.2, CB-22, CB-334E, CB-34, CB22B, CB24B, CB32B, CC24B
3013C, C1.5, C2.2, CB-22, CB-334E, CB-34, CB22B, CB24B, CB32B, CC24B
3111104
PUMP GP-ENGINE OIL
3013C, C1.1, C1.5, C2.2, CB-22, CB-334E, CB-34, CB22B, CB24B, CB32B, CC24B
3013C, C1.1, C1.5, C2.2, CB-22, CB-334E, CB-34, CB22B, CB24B, CB32B, CC24B
3111115
PUMP GP-WATER
3013C, C1.1, C1.5, C2.2, CB-22, CB-334E, CB-34, CB22B, CB24B, CB32B, CC24B
3013C, C1.1, C1.5, C2.2, CB-22, CB-334E, CB-34, CB22B, CB24B, CB32B, CC24B
1296259
PUMP GP-FUEL PRIMING
216, 216B, 216B3, 226B, 226B3, 232B, 242B, 247B, 247B3, 257B, 301.5, 302.5, 303.5, 304.5, 3116, 45, 527, 55, 554, 574, 902, 924F, 928F, 928G, 938F, 938G, 950F, 950F II, 950G, 960F, 962G, BG-225C, CB-1...
216, 216B, 216B3, 226B, 226B3, 232B, 242B, 247B, 247B3, 257B, 301.5, 302.5, 303.5, 304.5, 3116, 45, 527, 55, 554, 574, 902, 924F, 928F, 928G, 938F, 938G, 950F, 950F II, 950G, 960F, 962G, BG-225C, CB-1...
216, 216B, 216B3, 226B, 226B3, 232B, 242B, 247B, 247B3, 257B, 3013C, 3024, 3024C, AP-255E, BB-621C, C1.1, C1.5, C2.2, CB-22, CB-334E, CB-34, CB22B, CB24B, CB32B, CB34B, CB34B XW, CC24B, CC34B
216B, 216B3, 226B, 226B3, 232B, 242B, 247B, 247B3, 257B, 3003, 301.5, 3011C, 3013, 3013C, 3014, 302.5, 3024, 3024C, 303.5, 304.5, 902, AP-255E, BB-621C, C0.5, C0.7, C1.1, C1.5, C1.6, C2.2, CB-14, CB-2...
AP-900B, CB-214E, CB-22, CB-334E, CB-34, CP-433E, CP-44, CP-533E, CP-54B, CP-56, CP-573E, CP-663E, CP-68B, CP-74B, CP-76, CS-423E, CS-433C, CS-433E, CS-44, CS-533D, CS-533E, CS-54, CS-563D, CS-563E, C...
2957855
PUMP GP-PISTON
CP-76
CP-76
2788376
PUMP GP-PISTON
CP-76
CP-76
3436071
PUMP & MTG GP-GEAR
CB-44B, CB-54B, CD-54B
CB-44B, CB-54B, CD-54B
AP-600D, AP1000E, BG1000E, BG600D
3537493
PUMP GP-PISTON
CB-22
CB-22
3041620
PUMP GP-PISTON
CB-22
CB-22