3615605 PUMP GP-ENGINE OIL Caterpillar parts
349E, 349E L, 349E L HVG, 349E L VG, 349F L, 621K, 623K, 627K, 730C, 980M, 982M, C13
Rating:
Alternative (cross code) number:
CA3615605
361-5605
3615605
CA3615605
361-5605
3615605
Weight: 8 pounds 3 kg.
ARTICULATED TRUCK, WHEEL TRACTOR-SCRAPER,
Compatible equipment models: 3615605:
Number on catalog scheme:
6
For full view, you need register
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6282 Torque Wrench Extension 1 Start By:
Remove the engine oil relief valve and the oil strainer. Refer to Disassembly and Assembly, "Engine Oil Relief Valve - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Remove the following components from the engine in order to remove the rear main bearing with the crankshaft in position: flywheel, flywheel housing, rear oil seal housing and bridge assembly.Note: Use Tooling (A) in order to remove the front main bearing cap with the front housing and the engine oil pump in place. If Tooling (A) is not available, removal of the front cover and the engine oil pump will be necessary. The engine oil pump is attached to the front main bearing cap. Removal of the bolts is not possible with a socket. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Remove all necessary components in order to gain access to the specific main bearing cap.
Make sure that the main bearing cap is marked for the location and direction for installation. The main bearings and the main bearing caps must be installed in the same location.
Illustration 1 g00554537
Remove two bolts (1) and main bearing cap (2).
Illustration 2 g00554539
Remove lower main bearing (3) from main bearing cap (2). Keep the respective main bearing and the main bearing cap together for proper installation.
Illustration 3 g00554540
Push upper main bearing (4) from the opposite side of the bearing tab with a suitable tool. Carefully rotate the crankshaft while you push on the bearing. Remove upper main bearing (4) from the cylinder block. Keep the upper bearing halves together in order to ensure proper installation.
Repeat Steps 1 through 5 for the remaining main bearings.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6282 Torque Wrench Extension 1 Start By:
Remove the engine oil relief valve and the oil strainer. Refer to Disassembly and Assembly, "Engine Oil Relief Valve - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Remove the following components from the engine in order to remove the rear main bearing with the crankshaft in position: flywheel, flywheel housing, rear oil seal housing and bridge assembly.Note: Use Tooling (A) in order to remove the front main bearing cap with the front housing and the engine oil pump in place. If Tooling (A) is not available, removal of the front cover and the engine oil pump will be necessary. The engine oil pump is attached to the front main bearing cap. Removal of the bolts is not possible with a socket. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Remove all necessary components in order to gain access to the specific main bearing cap.
Make sure that the main bearing cap is marked for the location and direction for installation. The main bearings and the main bearing caps must be installed in the same location.
Illustration 1 g00554537
Remove two bolts (1) and main bearing cap (2).
Illustration 2 g00554539
Remove lower main bearing (3) from main bearing cap (2). Keep the respective main bearing and the main bearing cap together for proper installation.
Illustration 3 g00554540
Push upper main bearing (4) from the opposite side of the bearing tab with a suitable tool. Carefully rotate the crankshaft while you push on the bearing. Remove upper main bearing (4) from the cylinder block. Keep the upper bearing halves together in order to ensure proper installation.
Repeat Steps 1 through 5 for the remaining main bearings.
Parts pump Caterpillar catalog:
621, 621B, 621E, 621F, 621G, 621H, 621K, 621R, 623B, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC
320C, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336E, 336E HVG, 336E L, 336E LN, 345D, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, M330D
621, 621B, 621E, 621F, 621G, 621H, 621K, 621R, 623B, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC
621, 621B, 621E, 621F, 621G, 621H, 621K, 621R, 623B, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 631D, 631E, 631G, 633D, 633E II, 637D, 637E, 637G, 639D
627, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637, 637B, 637D, 637E, 637G, 639D
725, 725C, 730, 730C
120M, 120M 2, 12M, 140M, 140M 2, 14M, 160M, 160M 2, 16M, 215B, 215C, 215D, 219D, 225, 225D, 227, 229, 229D, 231D, 235B, 235C, 235D, 245, 245B, 245D, 311B, 311D LRR, 312, 312B L, 312C L, 312D, 312D L, ...
2368936
PUMP
784C, 785C, 785D, 789C, 789D, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, 980H, 980K, 980K HLG, 980M, 982M
784C, 785C, 785D, 789C, 789D, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, 980H, 980K, 980K HLG, 980M, 982M
3924658
PUMP GP-GEAR
980H, 980M, 982M
980H, 980M, 982M
2237718
PUMP GP-METERING
725, 725C, 730, 730C
725, 725C, 730, 730C
3421906
PUMP GP-GEAR
345D, 345D L, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L
345D, 345D L, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L
4448546
PUMP GP-GEAR
330D L, 336D, 336D2, 336E, 336E L, 349E, 349E L, 349F L
330D L, 336D, 336D2, 336E, 336E L, 349E, 349E L, 349F L
3475063
PUMP & MTG GP-GEAR
986H, 988K
986H, 988K
5N7894
PUMP GP-ENGINE OIL
D398, D398A, D398B
D398, D398A, D398B
854G, 854K, 992G, 992K
3T3733
PUMP GP-PRELUBE
3512, 3516, 3606, 3608, 3612, 3616, G3606, G3608, G3612, G3616
3512, 3516, 3606, 3608, 3612, 3616, G3606, G3608, G3612, G3616
256C, 262C, 277C, 279C, 287C, 289C
953D, AP-600D, AP-655D, BG600D, BG655D, C6.6, CP-56, CP-64, CS-64, CS-74, D6K LGP, M316D, M318D, M318D MH
2205976
PUMP GP-FUEL PRIMING
561N, D5N
561N, D5N
2998967
PUMP & MTG GP-HYDRAULIC
C11, C13, CX31-C13I, TH35-C11I, TH35-C13I
C11, C13, CX31-C13I, TH35-C11I, TH35-C13I