AVSPARE.COM
parts catalog

PUMP GP-METERING 3866614 - Caterpillar


3866614 PUMP GP-METERING Caterpillar parts
Rating:
26
Alternative (cross code) number:
CA3866614
386-6614
3866614
Caterpillar 3866614 PUMP GP-METERING
Weight: 12 pounds 5 kg.

Buy PUMP GP-METERING 3866614 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$12.47
 

19 Aug 2020

-: -
Genuine Cummins 3866614 WASHER,LOCK
Factory Direct Shipped Genuine Cummins Part || Availability can vary, please contact for availability before ordering || May take up to 20 business days to ship. Shipping depends upon availability
Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 1 g02118734
Schematic for the (L Station) Right Hopper Lift SwitchThis diagnostic code is associated with the (L Station) Right Hopper Lift Switch. The FMI 02 means that the ECM determined that the signal is intermittent, erratic, or incorrect. The ECM could be receiving invalid combinations from the circuit.Note: The LH Operator ECM is located under the LH Operator Platform.System Response:When this diagnostic code is active, the following occurs:
Switch defaults to hold.
Operator station fault lamp is active.Test Step 1. CHECK THE CONTINUITY OF THE SWITCH IN THE OFF (CENTER) POSITION
Turn the key start switch to the OFF position.
Remove the switch from the dash.
Unplug the switch from the wire harness.
With the switch in the OFF (Center) position, check the resistance from terminal 2 to the following terminals: terminal 1 and terminal 3.Expected Result:The resistances should be greater than 5000 ohms.Results:
OK - The resistances are greater than 5000 ohms. Proceed to Test Step 2.
NOT OK - The resistance is less than 5000 ohms on one of the readings.Repair: The switch has failed. Replace the switch.STOPTest Step 2. CHECK THE CONTINUITY OF THE SWITCH IN THE UP POSITION
Press and hold the switch in the UP position.
With the switch in the UP position, check the resistance from terminal 2 to terminal 1 and to terminal 3.Expected Result:The resistance should be less than 5 ohms on terminals 1 and 2. The resistance should be greater than 5000 ohms on terminals 2 and 3.Results:
OK - The resistances are correct. Proceed to Test Step 3.
NOT OK - The resistance is not less than 5 ohms from terminal 1 to terminal 2 or the resistance is not greater than 5000 ohms from terminal 3 to terminal 2.Repair: The switch has failed. Replace the switch.STOPTest Step 3. CHECK THE CONTINUITY OF THE SWITCH IN THE DOWN POSITION
Place the switch in the DOWN position.
With the switch in the DOWN position, check the resistance from terminal 2 to terminal 1 and to terminal 3.Expected Result:The resistance should be less than 5 ohms from terminal 3 to terminal 2. The resistance should be greater than 5000 ohms from terminal 1 to terminal 2.Results:
OK - The resistances are correct. Proceed to Test Step 4.
NOT OK - The resistance is not less than 5 ohms from terminal 3 to terminal 2 or the resistance is not greater than 5000 ohms from terminals 2 to terminal 1. Repair: The switch has failed. Replace the switch.STOPTest Step 4. CHECK THE HARNESS
The disconnect switch and the key start switch remain in the OFF position.
The machine harness remains disconnected from the switch.
Disconnect the J1 and J2 machine harness connectors from the ECM.
Measure the resistance from contact J1-64 (wire T836-BU) of the machine harness to all the contacts that are used in machine harness connectors for the ECM.
Measure the resistance from contact J1-63 (wire T835-PK) of the machine harness to all the contacts that are used in machine harness connectors for the ECM.Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
YES - Each resistance measurement is greater than

Caterpillar parts catalog:

Caterpillar parts catalog
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY C4.4 Engine
420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY C4.4 Engine
430F2 Center Pivot Backhoe Loader LYD00001-UP (MACHINE) POWERED BY C4.4 Engine
430F2 IT Center Pivot Backhoe Loader LYE00001-UP (MACHINE) POWERED BY C4.4 Engine
420F2 Center Pivot Backhoe Loader HWC00001-UP (MACHINE) POWERED BY C4.4 Engine
420F2 IT Center Pivot Backhoe Loader HWD00001-UP (MACHINE) POWERED BY C4.4 Engine
430F2 Center Pivot Backhoe Loader HWE00001-UP (MACHINE) POWERED BY C4.4 Engine
430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY C4.4 Engine
415F2 IL Backhoe Loader PF400001-UP (MACHINE) POWERED BY C3.4 Engine
420F2 Center Pivot Backhoe Loader LBS00001-UP (MACHINE) POWERED BY 3054C, C4.4 Engine
420F2 ADL (Air Deployable Loader) NSB00001-UP (MACHINE) POWERED BY 3054C Engine


Parts pump Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.