PUMP GP-METERING 3964888 - Caterpillar

Install bracket assembly (8) and slack adjuster group (5) onto block (A) and secure using two hard washers (26) and two bolts (28).
Install dust cap (2) onto quick disconnect coupler assembly (15).
Illustration 36 g03274358
View from behind front support assembly
(5) Slack adjuster group
(7) Tube assembly
(13) Elbow assembly
(21) Clip
(23) Hard washer
(25) Bolt
(30) Clip
Install tube assembly (7) onto elbow assembly (13) on slack adjuster group (5). Secure tube assembly (7) using one clip (30), four clips (21), five hard washers (23), and five bolts (25).
Illustration 37 g03274397
Inside front left-hand side
(B) Brake control group
(5) Slack adjuster group
(9) Hose assembly
(10) Hose assembly
(12) Connector assembly
(17) O-Ring seal
(18) Elbow
Install one end of hose assembly (10) with O-ring seal (17) onto elbow (18) on slack adjuster group (5). Install the other end of hose assembly (10) onto brake control group (B).
Install one end of hose assembly (9) onto connector assembly (12) on slack adjuster group (5).
Illustration 38 g03274416
Inside front left-hand side
(9) Hose assembly
(24) Bolt
(23) Hard washer
(22) Grommet
(20) Clip
(19) Clip
Secure hose assembly (9) using grommet (22), clip (20), clip (19), hard washer (23), and bolt (24).
Illustration 39 g03274456
View of left-hand side
(C) Hose assembly
(1) Block
(3) Block
(6) Plate
(9) Hose assembly
(14) Connector assembly
(17) O-ring seal
(27) Hard washer
(29) Bolt
Remove hose assembly (C) installed in Step 41 of Section "Install the 247-3752 Hydraulic Oil Cooler Lines Group". Retain hardware.
Install connector assembly (14) onto wheel group.
Install O-ring seal (17) into plate (6). Install plate (6) and hose assembly (C) onto wheel group with hardware retained in Step 8.
Install hose assembly (9) onto connector assembly (14).
Install block (3) and block (1) around hose assembly (9). Secure block (3), block (1). and hose assembly (9) onto plate (6) with two hard washers (27) and two bolts (29).
Illustration 40 g03274877
View of right-hand side
(4) Hose assembly
(7) Tube assembly
(16) Union assembly
(19) Clip
(20) Clip
(22) Grommet
(23) Hard washer
(24) Bolt
Install union assembly (16) onto tube assembly (7). Install hose assembly (4) onto tube assembly (7).
Secure hose assembly (4) using grommet (22), clip (20), clip (19), hard washer (23), and bolt (24).
Illustration 41 g03274897
View of right-hand side
(D) Hose assembly
(1) Block
(3) Block
(4) Hose assembly
(6) Plate
(17) O-ring seal
(27) Hard washer
(29) Bolt
Remove hose assembly (D) which was installed in Step 38 of Section "Install the 247-3752 Hydraulic Oil Cooler Lines Group". Retain hardware.
Install connector assembly (14) onto wheel group.
Install O-ring seal (17) into plate (6). Install plate (6) and hose assembly (D) onto wheel group with hardware retained in Step 15.
Install hose assembly (4) onto connector assembly (14).
Install block (3) and block (1) around hose assembly (4). Secure block (3), block (1). and hose assembly (4) onto plate (6) with two hard washers (27) and two bolts (29).Register the Retrofit
Because retrofits to a prime product will change the configuration of the product, updating the configuration in SIMSi and AIMS is important. If the retrofit information is not provided, Caterpillar will not be able to provide important product updates.The following information includes instructions on registering the updates and retrofits.
When performing a retrofit installation, record the vital information in Table 6.Note: If the procedure is performed by the customer, ask the customer to