3G6002 PUMP GP-GEAR Caterpillar parts
193, D9H
Rating:
Alternative (cross code) number:
CA3G6002
3G-6002
3G6002
CA3G6002
3G-6002
3G6002
Weight: 54 pounds 24 kg.
HYDRAULIC CONTROL, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
RAParts 1U0547 Fits Caterpillar Fits CAT Seal Kit for 3G6002 fits Several Models
Reliable Aftermarket Parts One New Aftermarket Replacement Seal Kit That Fits Caterpillar Models. For 3G6002. Replaces Part Num || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications. || All OEM part numbers and logos are to be used for identification purposes only.
Reliable Aftermarket Parts One New Aftermarket Replacement Seal Kit That Fits Caterpillar Models. For 3G6002. Replaces Part Num || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications. || All OEM part numbers and logos are to be used for identification purposes only.
RAParts 1U0547 Fits Caterpillar Fits CAT Seal Kit for 3G6002 fits Several Models
Reliable Aftermarket Parts One New Aftermarket Replacement Seal Kit That Fits Caterpillar Models. For 3G6002. Replaces Part Num || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications. || All OEM part numbers and logos are to be used for identification purposes only.
Reliable Aftermarket Parts One New Aftermarket Replacement Seal Kit That Fits Caterpillar Models. For 3G6002. Replaces Part Num || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications. || All OEM part numbers and logos are to be used for identification purposes only.
Number on catalog scheme:
For full view, you need register
Information:
Remove Governor
START BY:a. remove fuel ratio control (if so equipped) 1. Remove bolts (1), cover (2) and the cover gasket from the governor housing. 2. Remove the bolt from stop collar (3). Remove collar (3). Remove the collar and spring (4) from below collar (3). 3. Install tool (A) in the fuel pump housing. Make sure the correct end of tool (A) is used. Move governor bolt (5) until tool (A) is in place and the racks are in center (zero) position.4. Remove bolts (7). Remove governor housing (6) and gasket.5. Disconnect fuel lines (8). 6. Remove the four bolts from location (9) that hold the governor plate to the fuel injection pump housing. Remove plate (10). If necessary, hold the racks in the center (zero) position against tool (A) with a screwdriver while the governor plate is removed. It is possible to remove the governor and governor plate as a unit. The above steps must be followed before the governor can be installed again on the injection pump housing.Install Governor
Drive assembly (13) must be removed from governor plate (12) before the governor plate is installed on the injection pump housing. The drive assembly can be damaged if it is installed with the governor plate and is not in alignment with the drive pinion assembly.
1. Install a new gasket on the injection pump housing.2. Put governor plate (12) in position on the fuel pump housing. Make sure dowels (14) in governor plate (12) are in alignment with the holes in the injection pump housing.3. Install stop (6) in gear (10). Make sure the wide space in stop (6) is in alignment with the wide space on pinion assembly (1).4. Install drive assembly (13). Align the holes in gear (10), stop (6) and drive assembly (13). Install pin (8). Install ring (11).5. Install a new gasket on the governor plate. Install spring (9), spring washer, flat washer, and spring washer (not shown) and seat (7). Install governor housing (2).6. Install spring (5) and collar (4). Install stop collar (3).7. Install the bolts that hold the governor housing and plate to the injection pump housing.8. Check the governor adjustment. See Governor Adjustments in Testing And Adjusting. 9. Install gasket (16) and cover (15). Make sure the dowel in cover (15) is in alignment with the notch in collar (3).10. Connect fuel lines (17) to the governor plate.END BY:a. install fuel ratio control (if so equipped)Disassemble Governor
START BY:a. remove govenor 1. Remove plug (4) and the gasket. Remove the spring, plunger and washer from the speed limiter.2. Bend the locks down on torque spring assembly (1). Remove the torque spring assembly.3. Remove high idle screw (2) and low idle screw (3). 4. Bend lock (7) down, and remove the bolt from control lever (8). Remove shaft (5) and control lever (8).5. Remove the lip-type seals and shaft bearings from housing (6). 6. Remove seat (9), the spring washer, flat washer and spring washer (10). Remove spring washer (11). Remove spring
START BY:a. remove fuel ratio control (if so equipped) 1. Remove bolts (1), cover (2) and the cover gasket from the governor housing. 2. Remove the bolt from stop collar (3). Remove collar (3). Remove the collar and spring (4) from below collar (3). 3. Install tool (A) in the fuel pump housing. Make sure the correct end of tool (A) is used. Move governor bolt (5) until tool (A) is in place and the racks are in center (zero) position.4. Remove bolts (7). Remove governor housing (6) and gasket.5. Disconnect fuel lines (8). 6. Remove the four bolts from location (9) that hold the governor plate to the fuel injection pump housing. Remove plate (10). If necessary, hold the racks in the center (zero) position against tool (A) with a screwdriver while the governor plate is removed. It is possible to remove the governor and governor plate as a unit. The above steps must be followed before the governor can be installed again on the injection pump housing.Install Governor
Drive assembly (13) must be removed from governor plate (12) before the governor plate is installed on the injection pump housing. The drive assembly can be damaged if it is installed with the governor plate and is not in alignment with the drive pinion assembly.
1. Install a new gasket on the injection pump housing.2. Put governor plate (12) in position on the fuel pump housing. Make sure dowels (14) in governor plate (12) are in alignment with the holes in the injection pump housing.3. Install stop (6) in gear (10). Make sure the wide space in stop (6) is in alignment with the wide space on pinion assembly (1).4. Install drive assembly (13). Align the holes in gear (10), stop (6) and drive assembly (13). Install pin (8). Install ring (11).5. Install a new gasket on the governor plate. Install spring (9), spring washer, flat washer, and spring washer (not shown) and seat (7). Install governor housing (2).6. Install spring (5) and collar (4). Install stop collar (3).7. Install the bolts that hold the governor housing and plate to the injection pump housing.8. Check the governor adjustment. See Governor Adjustments in Testing And Adjusting. 9. Install gasket (16) and cover (15). Make sure the dowel in cover (15) is in alignment with the notch in collar (3).10. Connect fuel lines (17) to the governor plate.END BY:a. install fuel ratio control (if so equipped)Disassemble Governor
START BY:a. remove govenor 1. Remove plug (4) and the gasket. Remove the spring, plunger and washer from the speed limiter.2. Bend the locks down on torque spring assembly (1). Remove the torque spring assembly.3. Remove high idle screw (2) and low idle screw (3). 4. Bend lock (7) down, and remove the bolt from control lever (8). Remove shaft (5) and control lever (8).5. Remove the lip-type seals and shaft bearings from housing (6). 6. Remove seat (9), the spring washer, flat washer and spring washer (10). Remove spring washer (11). Remove spring
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts pump Caterpillar catalog:
57, 58, 594H, D7G, D9H
571G, D7G, D8K, D9H
571G, 572G, 583K, 594H, D7F, D7G, D8K, D9H
594H, D9H
16, 594H, 769, 824B, 834, 988, D10, D9H
583K, 594H, D8K, D9H
583K, 594, 594H, D8H, D8K, D9G, D9H
594H, D9H
8S2706
PUMP GP-FUEL PRIMING
594, 594H, D9G, D9H
594, 594H, D9G, D9H
594H, D9H
594H, D353C, D379A, D379B, D398, D398A, D398B, D399, D9G, D9H
963, 973, 992C, D10, D9H
2W0058
PUMP GP-GOV & FUEL INJ
3306, 3306B, D25C, D25D, D300B, D30C, D350C, D35C
3306, 3306B, D25C, D25D, D300B, D30C, D350C, D35C
1542803
PUMP & MTG GP-SECONDARY STEER
950G, 962G, IT62G
950G, 962G, IT62G
2803457
PUMP GP-PISTON
CB-634D
CB-634D
950H, 950K, 962H, 962K, IT62H
0844899
PUMP GP-TRACTION
CB-214B
CB-214B
3065719
PUMP & MTG GP-HYDRAULIC
AD55B, AD60
AD55B, AD60
7S6985
PUMP GP-SCAVENGE
641B, 650B, 651E, 657B, 657E, 657G, 666B
641B, 650B, 651E, 657B, 657E, 657G, 666B
1275264
PUMP AS
311B, 311C, 312B, 325B, 330B
311B, 311C, 312B, 325B, 330B
2W9103
PUMP GP-GOV & FUEL INJ
3406B, 3406C
3406B, 3406C
824G, 824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 980H