4160021 PUMP AS-WASHER Caterpillar parts
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 525B, 535B, 545, 583T, 587R, 587T, 725C, 730C, 824K, 825K, 826K, 834K, 836K, 9...
Rating:
Alternative (cross code) number:
CA4160021
416-0021
4160021
CA4160021
416-0021
4160021
Weight: 0.20 pounds 0 kg.
ARTICULATED TRUCK, WHEEL SKIDDER,
Compatible equipment models: 4160021:
Number on catalog scheme:
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6238 Guide Bolt 2
B 8T-3052 Degree Wheel 1
Thoroughly clean the top of the cylinder block and the bottom of the cylinder head. Ensure that there is no debris in the cylinder bores.
Illustration 1 g00550165
Typical example
Place cylinder head gasket (3) on dowels (4) on top of the cylinder block. The cylinder head gasket (3) is stamped "FRONT TOP". Do not use any sealant or compound on the cylinder head gasket.
Install Tool (A) in positions 15 and 20 in the cylinder block. Refer to Illustration 5.
Illustration 2 g00550163
Typical example
Attach a suitable lifting device to cylinder head (2) .
Place cylinder head (2) on the cylinder block. Ensure that the cylinder head is positioned on dowels (4) and that cylinder head gasket (3) is positioned correctly.
Remove Tool (A) .
Illustration 3 g00550160
3054 Engine
Illustration 4 g00572265
3056 Engine
Lubricate cylinder head bolts (1) with clean engine oil.
Illustration 5 g00550162
3054 Engine
Illustration 6 g00572255
3056 Engine
Gradually tighten all of the bolts in a numerical sequence to a torque of 110 N m (80 lb ft).
Tighten all of the bolts again in a numerical sequence to a torque of 110 N m (80 lb ft).
Place an index mark on the bolts and use Tool (B) in order to further tighten the bolts.
Turn the short bolts that are marked with an "S" for an additional 150 degrees (2.5 flats).
Turn the medium length bolts that are marked with an "M" for an additional 180 degrees (3.0 flats).
Turn the long bolts that are marked with an "L" for an additional 210 degrees (3.5 flats).Note: Refer to the Testing and Adjusting Module, "Cylinder Compression" for the correct procedure to test the cylinder head.End By:
Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".
Install the water outlet manifold. Refer to Disassembly and Assembly, "Water Outlet Manifold - Install".
Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install".
Install the air inlet manifold. Refer to Disassembly and Assembly, "Air Inlet Manifold - Install".
Install the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection Nozzles - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6238 Guide Bolt 2
B 8T-3052 Degree Wheel 1
Thoroughly clean the top of the cylinder block and the bottom of the cylinder head. Ensure that there is no debris in the cylinder bores.
Illustration 1 g00550165
Typical example
Place cylinder head gasket (3) on dowels (4) on top of the cylinder block. The cylinder head gasket (3) is stamped "FRONT TOP". Do not use any sealant or compound on the cylinder head gasket.
Install Tool (A) in positions 15 and 20 in the cylinder block. Refer to Illustration 5.
Illustration 2 g00550163
Typical example
Attach a suitable lifting device to cylinder head (2) .
Place cylinder head (2) on the cylinder block. Ensure that the cylinder head is positioned on dowels (4) and that cylinder head gasket (3) is positioned correctly.
Remove Tool (A) .
Illustration 3 g00550160
3054 Engine
Illustration 4 g00572265
3056 Engine
Lubricate cylinder head bolts (1) with clean engine oil.
Illustration 5 g00550162
3054 Engine
Illustration 6 g00572255
3056 Engine
Gradually tighten all of the bolts in a numerical sequence to a torque of 110 N m (80 lb ft).
Tighten all of the bolts again in a numerical sequence to a torque of 110 N m (80 lb ft).
Place an index mark on the bolts and use Tool (B) in order to further tighten the bolts.
Turn the short bolts that are marked with an "S" for an additional 150 degrees (2.5 flats).
Turn the medium length bolts that are marked with an "M" for an additional 180 degrees (3.0 flats).
Turn the long bolts that are marked with an "L" for an additional 210 degrees (3.5 flats).Note: Refer to the Testing and Adjusting Module, "Cylinder Compression" for the correct procedure to test the cylinder head.End By:
Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".
Install the water outlet manifold. Refer to Disassembly and Assembly, "Water Outlet Manifold - Install".
Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install".
Install the air inlet manifold. Refer to Disassembly and Assembly, "Air Inlet Manifold - Install".
Install the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection Nozzles - Install".
Cat SIS web machinery list:
Parts pump Caterpillar catalog:
16M, 631D, 631E, 631G, 633E II, 637E, 637G, 966H, 972H, C-15, C-16, C-18, C15, C16, D8N, TH35-C15T
16M, 345D L, 572R II, 966H, 972H, C-12, C13, D7R II, MTC835
120G, 12G, 12H, 12H ES, 12H NA, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 214B, 235, 3114, 3116, 3126, 3126B, 3126E, 3176, 3176B, 3176C, 3196,...
120G, 12G, 130G, 140G, 140H, 143H, 14G, 14H, 160G, 160H, 163H, 1673C, 16H, 235B, 24H, 3116, 311C, 311D LRR, 3126, 3126B, 3126E, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315C, 315D L,...
120H, 120H ES, 120H NA, 120K, 120K 2, 12K, 12M, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 160K, 30/30, 3116, 3126, 3126B, 3126E, 320B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L,...
12H, 140M, 160M, 2290, 2390, 2391, 2491, 2590, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 511, 521, 522, 532, 541, 551, 552, 627G, 637D, 637E, 637G...
12H, 140M, 140M 2, 160M, 160M 2, 2290, 2390, 330C, 330C L, 330D, 330D FM, 330D L, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 552, 552 ...
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 420E, 430E, 553C, 613G, 914G, 924H, 924HZ, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, AP1000E, AP1055E, BG500E, BG600D, BG655D, C4.4, C6.6, CB-54, CB-54B, CB...
120M, 12M, 2470C, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L, 525D, 535D, 545D, 553C, 559, 613G, 924H, 924HZ, 924K, 928H, 928HZ, 930K, 938H, 938K, 950 GC, 953D, 963D, AP-600D, AP-655D,...
120M 2, 2384C, 2484C, 2570C, 2670C, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 525D, 535D, 545D, 555D, 559C, 563C, 573C, 579C, 924K, 930K, 938K, 95...
583T, 621G, 623G, 627F, 627G, 657E, 824H, 825H, 826H, 980H, C-15, C-16, D8T, PL83
120M 2, 2384C, 2484C, 312E, 324E LN, 559C, 579C, 930K, 938K, 966F II, BG1055E, C4.4, C6.6, C7.1, D6K2 LGP
2892904
PUMP GP-GEAR
583T, 587R, 587T
583T, 587R, 587T
1724036
PUMP GP-HAND
973C, 973D
973C, 973D
12H, 330C, 330C FM, 330C L, 330C MH, 627G, 637G, D6R II
2731582
PUMP GP-GEAR
963D
963D
2519555
PUMP GP-GEAR
953D
953D
2676476
PUMP GP-ELECTRIC
D6R III, D6T
D6R III, D6T
631G, 637G, D6R, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7R II, D7R XR, D8R, D9R
2606782
PUMP GP-GEAR
D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP
D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP