4179305 PUMP AS-WATER Caterpillar parts
312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, 320E L, 320E LN, 320E LRR, 323E L, C4.4, C4.4XQ100, C4.4XQ80, CB-44B, CB-54B, CP-54B, CP-68B, CP-74B, CS-56B, CS-66B, CS-76B, CS-78B, CW-34
Rating:
Alternative (cross code) number:
CA4179305
417-9305
4179305
CA4179305
417-9305
4179305
Weight: 15 pounds 7 kg.
EXCAVATOR, VIBRATORY COMPACTOR,
Compatible equipment models: 4179305:
For full view, you need register
Information:
Illustration 1 g02149288
Connections of the blade raise solenoid
This diagnostic code is associated with the blade raise solenoid. The FMI 06 means that the ECM has determined that there is a short to ground.The possible causes of this diagnostic code are listed:
The energize circuit of the solenoid is shorted to ground.
The solenoid has failed.
The ECM has failed. An ECM failure is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1198 - FMI 06 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.Test Step 1. Check the solenoid
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Observe the status of the diagnostic code.
Disconnect the solenoid with the active diagnostic code from the machine harness. Expected Result:The FMI 06 changes to FMI 05 after the solenoid is disconnected.Results:
YES - The FMI 06 changes to FMI 05 after the solenoid is disconnected. The circuit is correct.Repair: The solenoid has failed. Replace the solenoid. Verify that the new solenoid has corrected the problem.STOP
NO - The FMI 06 remains active. Proceed to Test Step 2.Test Step 2. Check the energize circuit of the solenoid for a short to ground
Turn the key start switch and the disconnect switch to the OFF position.
The solenoid remains disconnected from the machine harness.
Disconnect the machine harness connectors from the ECM.
At the machine harness connector, measure the resistance from the signal contact J1-48 wire (H713-PK(Pink)) to all contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
YES - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NO - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J1-48 wire (H713-PK(Pink)) and the circuit with the low resistance measurement.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 3. Check the status of the diagnostic code
Inspect the harness connectors. Clean the contacts of the harness connectors and check the wires for damage to the insulation. Damage is caused by excessive heat, corrosion, or chafing.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit.
Reconnect all harness connectors in order to make sure that the connectors are fully seated. Also, make sure that the clips for each connector are fastened.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Determine if the CID 1198 - FMI 06 diagnostic code is active. Expected Result:The CID 1198 - FMI 06 diagnostic code is not active.Results:
YES - The CID 1198 - FMI 06 diagnostic code is not active. The problem does not exist at this time.Repair: The initial diagnostic code was probably caused by a poor electrical connection
Parts pump Caterpillar catalog:
236B, 236B3, 242B3, 252B, 252B3, 257B3, 259B3, 267B, CW-34
120M 2, 2384C, 2484C, 2570C, 2670C, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 525D, 535D, 545D, 555D, 559C, 563C, 573C, 579C, 924K, 930K, 938K, 95...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, ...
3903122
PUMP AS-FUEL INJECTION
3.4B IOPU, 311F LRR, C3.4B, CB-44B, CB-54B, CD-54B, CW-14
3.4B IOPU, 311F LRR, C3.4B, CB-44B, CB-54B, CD-54B, CW-14
3456608
PUMP-COOLANT
320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 924K, 930K, 938K, C6.6, C7.1, D6K2 LGP, D6N LGP
320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 924K, 930K, 938K, C6.6, C7.1, D6K2 LGP, D6N LGP
120M 2, 2384C, 2484C, 312E, 324E LN, 559C, 579C, 930K, 938K, 966F II, BG1055E, C4.4, C6.6, C7.1, D6K2 LGP
2570C, 2670C, 312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 563C, 573C, 924K, 950K, 962K, BG1000E, C7...
120M, 120M 2, 12M, 140M, 140M 2, 14M, 160M, 160M 2, 16M, 215B, 215C, 215D, 219D, 225, 225D, 227, 229, 229D, 231D, 235B, 235C, 235D, 245, 245B, 245D, 311B, 311D LRR, 312, 312B L, 312C L, 312D, 312D L, ...
3687702
PUMP GP-FUEL TRANSFER
311F LRR, 312E, 314E LCR, 316E L, 318E L
311F LRR, 312E, 314E LCR, 316E L, 318E L
3406297
PUMP
CB-44B, CB-54B, CD-54B
CB-44B, CB-54B, CD-54B
3688646
PUMP
CW-34
CW-34
3918862
PUMP GP-HAND
CB-44B, CB-54B
CB-44B, CB-54B
120M 2, 2384C, 2484C, 2570C, 2670C, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 525D, 535D, 545D, 555D, 559C, 563C, 573C, 579C, 924K, 930K, 938K, 95...
3581424
PUMP AS
C280-12, C280-16
C280-12, C280-16
3581423
PUMP AS
C280-12, C280-16
C280-12, C280-16
3876877
PUMP AS-WATER
C140-16
C140-16
120M 2, 2384C, 2484C, 2570C, 2670C, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 525D, 535D, 545D, 555D, 559C, 563C, 573C, 579C, 924K, 930K, 938K, 95...
312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, C4.4, CP-54B, CP-68B, CP-74B, CS-54B, CS-56B, CS-64B, CS-66B, CS-76B, CS-78B, CW-34
3689040
PUMP GP-FUEL INJECTION
C4.4, C7.1
C4.4, C7.1