4W4738 PUMP GP-GOV, FUEL INJ & TFR Caterpillar parts
3408, 3408B
Rating:
Alternative (cross code) number:
CA4W4738
4W-4738
4W4738
CA4W4738
4W-4738
4W4738
Weight: 5 pounds 2 kg.
INDUSTRIAL ENGINE, MARINE ENGINE,
Information:
General Hazard Information
To prevent injury or death, all machines equipped with a Caterpillar PL522 or 523 system require a warning label that is clearly posted in the cab.
This machine is equipped with a Caterpillar Product Link communication device. When electric detonators are used, this communication device should be deactivated within 12 m (40 ft) of a blast site, or within the distance mandated under applicable legal requirements. Failure to do so could cause interference with blasting operations and result in serious injury or death.
To prevent possible personal injury during installation, removal, testing, and adjustment of the Product Link system, use an approved access system and appropriate fall protection to reach the intended location. Do not climb on the machine.
The blast site is defined as the area that handles explosive material during loading. This includes the perimeter that is formed by the loaded blast holes. If the machine is required to work within 12 m (40 ft) of a blast area, then the operator must take one of the following precautions:
Disconnect the PL522 or 523 module from the power source by disconnecting the wiring harness at the PL522 or 523 module.
Temporarily remove the PL522 or 523 module from the machine.
Add an ON/OFF switch in order to allow the PL522 or 523 module to be turned off from the cab.Consult your Caterpillar Dealer if there are any questions.The following PL522 and 523 specifications are provided to aid in conducting hazard assessments and ensuring compliance with all local regulations.Product Link Transmitter Power - 0.747 to 1.738 Watts (varies with frequency)Transmit Frequency Range - 824 to 849 MHz, 880 to 915 MHz, 1710 to 1785 MHz, 1850 to 1910 MHzGeneral Troubleshooting Information
Many Caterpillar machines have a published Electrical System Schematic that reflects a Product Link installation. Refer to these schematics if a troubleshooting procedure instructs you to "Repair the harness". Perform continuity checks and resistance checks at the connectors in order to locate a failure in the harness. At a component connector, always check the ground circuit. Less than 5 ohms of resistance is required from the ground contacts to frame ground. A problem may be incorrectly diagnosed, if an excessive resistance that is greater than 5 ohms is present in the ground circuit. During a troubleshooting procedure, inspect all component and harness connections before a component is replaced. If these connections are not clean and tight, the connection may cause an electrical problem.The problem can be permanent or the problem may be intermittent. Ensure that the wires are pushed into the connectors completely. Make sure that the connections are tight before other tests are performed. A failure of an electrical component may cause a failure of another component or a failure may be caused by the failure of other components. Always attempt to find a failure. The following test procedures are written for a technician with a working knowledge of electricity and electronics. Correct the cause of a failure in the electrical system before you replace a component.The test procedures that
To prevent injury or death, all machines equipped with a Caterpillar PL522 or 523 system require a warning label that is clearly posted in the cab.
This machine is equipped with a Caterpillar Product Link communication device. When electric detonators are used, this communication device should be deactivated within 12 m (40 ft) of a blast site, or within the distance mandated under applicable legal requirements. Failure to do so could cause interference with blasting operations and result in serious injury or death.
To prevent possible personal injury during installation, removal, testing, and adjustment of the Product Link system, use an approved access system and appropriate fall protection to reach the intended location. Do not climb on the machine.
The blast site is defined as the area that handles explosive material during loading. This includes the perimeter that is formed by the loaded blast holes. If the machine is required to work within 12 m (40 ft) of a blast area, then the operator must take one of the following precautions:
Disconnect the PL522 or 523 module from the power source by disconnecting the wiring harness at the PL522 or 523 module.
Temporarily remove the PL522 or 523 module from the machine.
Add an ON/OFF switch in order to allow the PL522 or 523 module to be turned off from the cab.Consult your Caterpillar Dealer if there are any questions.The following PL522 and 523 specifications are provided to aid in conducting hazard assessments and ensuring compliance with all local regulations.Product Link Transmitter Power - 0.747 to 1.738 Watts (varies with frequency)Transmit Frequency Range - 824 to 849 MHz, 880 to 915 MHz, 1710 to 1785 MHz, 1850 to 1910 MHzGeneral Troubleshooting Information
Many Caterpillar machines have a published Electrical System Schematic that reflects a Product Link installation. Refer to these schematics if a troubleshooting procedure instructs you to "Repair the harness". Perform continuity checks and resistance checks at the connectors in order to locate a failure in the harness. At a component connector, always check the ground circuit. Less than 5 ohms of resistance is required from the ground contacts to frame ground. A problem may be incorrectly diagnosed, if an excessive resistance that is greater than 5 ohms is present in the ground circuit. During a troubleshooting procedure, inspect all component and harness connections before a component is replaced. If these connections are not clean and tight, the connection may cause an electrical problem.The problem can be permanent or the problem may be intermittent. Ensure that the wires are pushed into the connectors completely. Make sure that the connections are tight before other tests are performed. A failure of an electrical component may cause a failure of another component or a failure may be caused by the failure of other components. Always attempt to find a failure. The following test procedures are written for a technician with a working knowledge of electricity and electronics. Correct the cause of a failure in the electrical system before you replace a component.The test procedures that
Caterpillar SIS machinery equipment:
Caterpillar SIS
3408B Marine Engine 99U04604-07598 »
4W-4738
PUMP GP-GOV, FUEL INJ & TFR
3408B Marine Engine 99U04604-07598 »
4W-4738
PUMP GP-GOV, FUEL INJ & TFR
3408B Industrial Engine 67U11092-UP »
4W-4738
PUMP GP-GOV, FUEL INJ & TFR
3408B Industrial Engine 67U11092-UP »
4W-4738
PUMP GP-GOV, FUEL INJ & TFR
3408C Marine Engine 99U07599-UP »
4W-4738
PUMP GP-GOV, FUEL INJ & TFR
3408B MARINE ENGINE 1LG00001-UP »
4W-4738
PUMP GP-GOV, FUEL INJ & TFR
Caterpillar parts catalog:
Parts pump Caterpillar catalog:
6N1043
PUMP GP-FUEL INJECTION
245, 3406, 3408, 3412, 621B, 631D, 633D, 637D, 639D, 768C, 769C, 772B, 773B, 988B, 992C
245, 3406, 3408, 3412, 621B, 631D, 633D, 637D, 639D, 768C, 769C, 772B, 773B, 988B, 992C
7N1185
PUMP GP-FUEL INJECTION
3408, 3412, 988B, D8L, D9L
3408, 3412, 988B, D8L, D9L
4N1101
PUMP GP-FUEL TRANSFER
3408, 3408B, 3408C, 3412, 3412C, 3412D, 631D, 631E, 633D, 637D, 637E, 639D, 651E, 657E, 768C, 769C, 771C, 772B, 773B, 775B, 988B, 990, 992C, 992D, D8L, D9L, PM3412, PR-1000, PR-450, PR-450C, PR-750B
3408, 3408B, 3408C, 3412, 3412C, 3412D, 631D, 631E, 633D, 637D, 637E, 639D, 651E, 657E, 768C, 769C, 771C, 772B, 773B, 775B, 988B, 990, 992C, 992D, D8L, D9L, PM3412, PR-1000, PR-450, PR-450C, PR-750B
4N1951
PUMP GP-WATER
3408, 3408B, 3408C, 3408E, 589, 631D, 631E, 631G, 633D, 633E II, 637D, 637E, 637G, 639D, 657E, 69D, 768C, 769C, 769D, 771C, 771D, 834B, 836, 988B, 988F, 988F II, AD40, AD45, AE40, AE40 II, D8L, D9N, D...
3408, 3408B, 3408C, 3408E, 589, 631D, 631E, 631G, 633D, 633E II, 637D, 637E, 637G, 639D, 657E, 69D, 768C, 769C, 769D, 771C, 771D, 834B, 836, 988B, 988F, 988F II, AD40, AD45, AE40, AE40 II, D8L, D9N, D...
4W5477
PUMP GP-FUEL TRANSFER
3408, 3408B, 3408C, 3412, 3412C, 3412D, 631D, 631E, 633D, 637D, 637E, 639D, 651E, 657E, 768C, 769C, 771C, 772B, 773B, 775B, 990, 992C, 992D, D9L, PM3412, PR-1000, PR-450, PR-450C, PR-750B
3408, 3408B, 3408C, 3412, 3412C, 3412D, 631D, 631E, 633D, 637D, 637E, 639D, 651E, 657E, 768C, 769C, 771C, 772B, 773B, 775B, 990, 992C, 992D, D9L, PM3412, PR-1000, PR-450, PR-450C, PR-750B
7C3613
PUMP GP-AUXILIARY
3408, 3408C, 3412, 3412C, 3412D
3408, 3408C, 3412, 3412C, 3412D
1614113
PUMP GP-ENGINE OIL
24M, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3456, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 651B, 657B, 657E, 657G, 735, 735B, 740, 740B, 770, 770G, 770G...
24M, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3456, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 651B, 657B, 657E, 657G, 735, 735B, 740, 740B, 770, 770G, 770G...
4N8734
PUMP GP-ENGINE OIL
3406C, 3406E, 3408, 3408B, 3408C, 3412, 3456, 631D, 631E, 633D, 637D, 637E, 639D, 657E, 768C, 769C, 771C, 824G, 825G, 826G, 834B, 836, 980G, 988B, C-15, C-16, C15, CG137-08, D350E II, D400E II, G3408,...
3406C, 3406E, 3408, 3408B, 3408C, 3412, 3456, 631D, 631E, 633D, 637D, 637E, 639D, 657E, 768C, 769C, 771C, 824G, 825G, 826G, 834B, 836, 980G, 988B, C-15, C-16, C15, CG137-08, D350E II, D400E II, G3408,...
1371338
PUMP GP-WATER
3408, 3408B, 3408C, 3408E, 589, 631D, 631E, 631G, 633E II, 637E, 637G, 657E, 69D, 769C, 769D, 771D, 834B, 836, 988B, 988F II, AD40, AD45, AE40, AE40 II, D8L, D9N, D9R, G3408, G3408B, G3408C, PM-565, P...
3408, 3408B, 3408C, 3408E, 589, 631D, 631E, 631G, 633E II, 637E, 637G, 657E, 69D, 769C, 769D, 771D, 834B, 836, 988B, 988F II, AD40, AD45, AE40, AE40 II, D8L, D9N, D9R, G3408, G3408B, G3408C, PM-565, P...
7W0561
PUMP GP-FUEL INJECTION
3408, 3408B, 3408C, 3412, 3412C, 3412D, 589, 631E, 637E, 651E, 657E, 768C, 769C, 771C, 772B, 773B, 775B, 834B, 836, 988B, 988F, 990, 992C, 992D, D10N, D8L, D9L, D9N, D9R, PM-565, PM3412, PR-1000, PR-4...
3408, 3408B, 3408C, 3412, 3412C, 3412D, 589, 631E, 637E, 651E, 657E, 768C, 769C, 771C, 772B, 773B, 775B, 834B, 836, 988B, 988F, 990, 992C, 992D, D10N, D8L, D9L, D9N, D9R, PM-565, PM3412, PR-1000, PR-4...
4N7498
PUMP GP-WATER
3408, 3408B, 589, 631D, 631E, 633D, 637D, 637E, 639D, 657E, 768C, 769C, 771C, 834B, 836, 988B, 988F, D8L, D9N, G3408, G3408B, PM-565, PR-450, PR-450C
3408, 3408B, 589, 631D, 631E, 633D, 637D, 637E, 639D, 657E, 768C, 769C, 771C, 834B, 836, 988B, 988F, D8L, D9N, G3408, G3408B, PM-565, PR-450, PR-450C
1052508
PUMP AS-FUEL PRIMING
120G, 12G, 12H, 12H ES, 12H NA, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 214B, 235, 3114, 3116, 3126, 3126B, 3126E, 3176, 3176B, 3176C, 3196,...
120G, 12G, 12H, 12H ES, 12H NA, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 214B, 235, 3114, 3116, 3126, 3126B, 3126E, 3176, 3176B, 3176C, 3196,...
3N7722
PUMP AS-OIL
G399
G399
4T6896
PUMP GP-METERING
416, 416B, 426, 426B, 428, 428B, 436, 436B, 438, 438B
416, 416B, 426, 426B, 428, 428B, 436, 436B, 438, 438B
3G9891
PUMP GP-GEAR
814B, 936, 936F, 950B, 950B/950E, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F, G936, R1300, R1300G, R1300G II
814B, 936, 936F, 950B, 950B/950E, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F, G936, R1300, R1300G, R1300G II
4364332
PUMP & MOUNTING GP
MH3037
MH3037