5151694 PUMP & MTG GP-PISTON Caterpillar parts
Rating:
Alternative (cross code) number:
CA5151694
515-1694
5151694
CA5151694
515-1694
5151694
Weight: 286 pounds 129 kg.
You can buy:
US$2,100.59
28 May 2025
FridayParts
Compare Prices:
As an associate, we earn commssions on qualifying purchases through the links below
Hydraulic Pump 515-1694 11R-1444 Compatible with CAT 24M Bulldozer Loader
DJCXYSM Tips: Please place an order and purchase based on the part number. The pictures are for reference only. If you have any questions or cannot find the part number you are looking for, please contact us and we will confirm it as soon as possible! || Product Name:Hydraulic Pump || Part Number:515-1694 5151694 11R1444 11R-1444 || Application: Compatible with CAT 24M Bulldozer Loader || NOTE: To avoid unnecessary returns please check the part number before purchasing or tell us the picture of your engine model and nameplate to reduce the error rate.
DJCXYSM Tips: Please place an order and purchase based on the part number. The pictures are for reference only. If you have any questions or cannot find the part number you are looking for, please contact us and we will confirm it as soon as possible! || Product Name:Hydraulic Pump || Part Number:515-1694 5151694 11R1444 11R-1444 || Application: Compatible with CAT 24M Bulldozer Loader || NOTE: To avoid unnecessary returns please check the part number before purchasing or tell us the picture of your engine model and nameplate to reduce the error rate.
Number on catalog scheme:
1
For full view, you need register
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
D 8T-5096 Dial Indicator 1
E 8T-3052 Degree Wheel 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01150312
Install dowel (8) in the crankshaft.Protrusion of dowel (8) from the crankshaft face ... 8.4 mm (0.33 inch)
Install dowel (9) in the crankshaft.Protrusion of dowel (9) from the crankshaft ... 4.1 0.5 mm (0.16 0.02 inch)
Install crankshaft gear (7) on the crankshaft with the keyway in alignment with dowel (9). Timing Mark "V" of the gear should face away from crankshaft (6).Note: Install the main bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the main bearings for final assembly.
Install the upper halves of the main bearings in the cylinder block.Note: Ensure that the main bearings are installed so that the bearing tabs fit into the notch in the cylinder block. The upper halves of the main bearings have the oil groove and the oil hole.
Illustration 2 g01150344
Install Tooling (A) and a suitable lifting device on each end of crankshaft (6). The weight of crankshaft (6) is approximately 188 kg (415 lb).
Install crankshaft (6) with Timing Mark "V" on the crankshaft gear in alignment with Timing Mark "V" on the cluster gear.
Install the thrust plates on each side of the No. 4 main bearing.Note: Install the thrust plates with the words "Block Side" toward the cylinder block.
Install the lower halves of the crankshaft main bearings in the main bearing caps.Note: Ensure that the main bearings are installed so that the bearing tabs fit into the notch in the main bearing cap.
Position main bearing caps (4) on the crankshaft.Note: Ensure that the numbers on the main bearing caps match the numbers on the cylinder block. Also ensure that the "FRONT" on the main bearing cap is installed toward the front of the cylinder block.
Lubricate the threads of bolts (3) with clean engine oil. Install bolts (3) and the washers.
Lubricate the threads of bolts (5) and the seal of the washer with clean engine oil. Install bolts (5) and the washers.Note: Inspect the washers that go on bolts (5).
Tighten bolts (3) and bolts (5) for the main bearing caps, as follows:
Tighten Bolt (A) to a torque of 258 14 N m (190 10 lb ft).Note: Bolt (A) is on the bearing tab side of the
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
D 8T-5096 Dial Indicator 1
E 8T-3052 Degree Wheel 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01150312
Install dowel (8) in the crankshaft.Protrusion of dowel (8) from the crankshaft face ... 8.4 mm (0.33 inch)
Install dowel (9) in the crankshaft.Protrusion of dowel (9) from the crankshaft ... 4.1 0.5 mm (0.16 0.02 inch)
Install crankshaft gear (7) on the crankshaft with the keyway in alignment with dowel (9). Timing Mark "V" of the gear should face away from crankshaft (6).Note: Install the main bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the main bearings for final assembly.
Install the upper halves of the main bearings in the cylinder block.Note: Ensure that the main bearings are installed so that the bearing tabs fit into the notch in the cylinder block. The upper halves of the main bearings have the oil groove and the oil hole.
Illustration 2 g01150344
Install Tooling (A) and a suitable lifting device on each end of crankshaft (6). The weight of crankshaft (6) is approximately 188 kg (415 lb).
Install crankshaft (6) with Timing Mark "V" on the crankshaft gear in alignment with Timing Mark "V" on the cluster gear.
Install the thrust plates on each side of the No. 4 main bearing.Note: Install the thrust plates with the words "Block Side" toward the cylinder block.
Install the lower halves of the crankshaft main bearings in the main bearing caps.Note: Ensure that the main bearings are installed so that the bearing tabs fit into the notch in the main bearing cap.
Position main bearing caps (4) on the crankshaft.Note: Ensure that the numbers on the main bearing caps match the numbers on the cylinder block. Also ensure that the "FRONT" on the main bearing cap is installed toward the front of the cylinder block.
Lubricate the threads of bolts (3) with clean engine oil. Install bolts (3) and the washers.
Lubricate the threads of bolts (5) and the seal of the washer with clean engine oil. Install bolts (5) and the washers.Note: Inspect the washers that go on bolts (5).
Tighten bolts (3) and bolts (5) for the main bearing caps, as follows:
Tighten Bolt (A) to a torque of 258 14 N m (190 10 lb ft).Note: Bolt (A) is on the bearing tab side of the
Parts pump Caterpillar catalog:
5079025
PUMP GP-LUBRICATION
Caterpillar
Caterpillar
4976219
PUMP AR-FUEL TRANSFER
Caterpillar
Caterpillar
4976217
PUMP AR-FUEL TRANSFER
Caterpillar
Caterpillar
4940424
PUMP GP-LUBRICATION
Caterpillar
Caterpillar
4925108
PUMP GP-PISTON
Caterpillar
Caterpillar
Caterpillar
5585341
PUMP GP-WATER
Caterpillar
Caterpillar
5416833
PUMP GP-WATER
Caterpillar
Caterpillar
5391444
PUMP GP-GEAR
Caterpillar
Caterpillar
5289296
PUMP & MTG GP-MAIN HYDRAULIC
Caterpillar
Caterpillar
5202928
PUMP & MOUNTING GP
Caterpillar
Caterpillar
Caterpillar