PUMP GP (SEM) 5337988 - Caterpillar

Required Parts
Note: Refer to individual installation instructions per segment for a detailed list of parts.Installation Procedure
Illustration 1 g00104545
Attach a "Do Not Operate" warning tag to the start switch or controls before you service or repair the equipment. These warning tags (Special Instruction, SEHS7332) are available from your Cat dealer.Installation Procedure of 281-8245 Auxiliary Hydraulic Lines Gp
Table 1
Parts List for 281-8245 Auxiliary Hydraulic Lines Gp Revision -00    
Item Number    Qty    Part Number
Part Name    
(1)     2     6C-6760 Manifold    
(2)     8     149-1738 Clip    
(3)     2     187-9977 Plate    
(4)     2     187-9978 Support As    
(5)     2     187-9981 Support As    
(6)     2     250-1440 Adapter As    
(7)     2     253-6455 Tube As    
(8)     2     253-6557 Hose As    
(9)     4     6V-8398 O-Ring Seal    
(10)     4     8T-4121 Hard Washer    
(11)     4     8T-4136 Bolt    
(12)     16     8T-4139 Bolt    
(13)     4     8T-4185 Bolt    
(14)     16     8T-4223 Hard Washer    
(15)     4     7X-2543 Bolt    
(16)     8     8T-4183 Bolt    
Illustration 2 g02144350
Illustration 3 g02144389
(A) 48 mm (1.9 inch) (B) 350 5 mm (13.8 0.2 inch) (C) 1750 mm (68.9 inch) (D) 1250 mm (49.21 inch) (E) 903.2 mm (35.6 inch) (F) 161.3 mm (6.4 inch)Note: Refer to Illustration 3 for locations of the supports, tubes, and ball valves.
Use two 8T-4223 Hard Washers (14) and two 8T-4139 Bolts (12) per support assembly. Mount 2 187-9978 Support As (4) to the operator side of the stick.
Use 2 149-1738 Clips (2), support 253-6455 Tube As (7).
Loosely install the clips with two 8T-4223 Hard Washers (14) and two 8T-4139 Bolts (12). When the tube is correctly positioned, tighten the bolts for the clips to the appropriate torque.
Insert one 6V-8398 O-Ring Seal (9) in both ends of the tube.
Attach one 253-6557 Hose As (8) to the 253-6455 Tube As (7). Tighten to a torque value of 76 4 N m (56.1 1 lb ft).
Use two 8T-4223 Hard Washers (14) and two 8T-4139 Bolts (12) per support assembly. Mount 2 187-9981 Support As (5) to the opposite side of the stick.
Repeat Step 2 through Step 5.
Use two 8T-4121 Hard Washers (10) and two 8T-4136 Bolts (11). Mount one 187-9977 Plate (3) to both sides of the stick. Refer to Illustration 3 for the location of the plates.
Use one 250-1440 Adapter As (6), attach one 6C-6760 Manifold (1) to the tube assemblies on both sides of the stick. Tighten to a torque value of 76 4 N m (56.1 1 lb ft).
Attach both manifolds to