AVSPARE.COM
parts catalog

PUMP GP-ENGINE OIL 5N7895 - Caterpillar


5N7895 PUMP GP-ENGINE OIL Caterpillar parts D398, D398A, D398B
Rating:
24
Alternative (cross code) number:
CA5N7895
5N-7895
5N7895
Caterpillar 5N7895 PUMP GP-ENGINE OIL
Weight: 39 pounds 17 kg.

Buy PUMP GP-ENGINE OIL 5N7895 Caterpillar genuine, new aftermarket tractor parts with delivery
GEN SET ENGINE, MARINE ENGINE,

Compatible equipment models: 5N7895:

GEN SET ENGINE  D398B  
INDUSTRIAL ENGINE  D398  
MARINE ENGINE  D398A   Caterpillar
Number on catalog scheme:
  For full view, you need register

Information:


Illustration 1 g01450978
Table 1
Specification for 115-3696 Front Idler Gp
Item Qty Part Specification Description
1 1 7H-3171 Pipe Plug Remove the pipe plug from the front idler assembly and apply air pressure to this port. The front idler assembly should sustain 245 to 265 kPa (36 to 38 psi) air pressure for a minimum of 30 seconds. Add 380 20 mL (12.8 0.7 oz) of 8C-3703 Oil. Apply 4C-4030 Thread Lock Compound to the threads of the pipe plug and install the pipe plug.
2 2 109-0885 Duo-Cone Seal Gp During assembly, the rubber toric seals and all the contacting surfaces must be clean and dry. Prior to assembly, apply a thin film of 6V-4876 Lubricant on the mating surfaces of the metal seals. Make sure that the seals are assembled square with the bore. The rubber toric seal should not bulge and the rubber toric seal should not twist.
3 2 8F-8882 O-Ring Seal Lubricate the O-ring seals with the lubricant that is being sealed.
4 2 6Y-2266 Pin Install the pin with the slit in the range that is specified. Refer to Illustration 1 for the correct position of the pin as shown.
C - - Specified range is 40 degrees.
D - - Angle from centerline of idler shaft is 20 degrees.
5 - - Before assembly, the surface must be clean and free of protective coating.
6 - - Install the idler shaft so that the identification mark "R" is oriented toward the rear of the front idler assembly.
- - - End play in axial direction:
Minimum is 0.26 mm (0.010 inch).
Maximum is 1.26 mm (0.050 inch).

Caterpillar parts catalog:

Caterpillar parts catalog
D398B GENERATOR SET ENGINE 35Z00001-UP
D398B ENGINE - ENGINES IN GENERAL ELECTRIC LOCOMOTIVES FOR T 66B00001-UP


Parts pump Caterpillar catalog:

3N2078 PUMP GP-FUEL TRANSFER
D346, D348, D349, D379, D379A, D379B, D398, D398A, D398B, D399
7N8599 PUMP GP-FUEL PRIMING
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 994D, D348, D349, D379, D379A, D379B, D398, D398A, D398B, D399, PM3508, PM3512, PM3516, PP3516, TH48-E80
3N4304 PUMP GP-AUXILIARY
D379, D379A, D398, D398A, D399
4L8232 PUMP AS-FUEL PRIMING
D343, D346, D348, D349, D353C, D379, D379A, D379B, D398, D398A, D398B, D399
5N5632 PUMP GP-FUEL TRANSFER
D379, D379A, D379B, D398, D398A, D398B, D399
3N4519 PUMP GP-SUMP
D398, D398A, D398B
4L8800 PUMP GP-WATER
D379, D379A, D379B, D398, D398A, D398B, D399, G379, G398, G399
3N0705 PUMP & FILTER GP
D346, D348, D349, D379A, D398A, D399
2S7264 PUMP ASSEMBLY FUEL VALVE
594H, D353C, D379A, D379B, D398, D398A, D398B, D399, D9G, D9H
8M2701 PUMP ASSEM.
D353C, D379A, D398A
5N3798 PUMP GP-OIL
D398, D398A, D398B
7L3222 PUMP GP-WATER
D379, D379A, D379B, D398, D398A, D399
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.