6Y4341 PUMP GP-CRESCENT Caterpillar parts
416, 426, 426B, 428, 428B, 436, 436B, 438, 438B, RT50
Rating:
Alternative (cross code) number:
CA6Y4341
6Y-4341
6Y4341
CA6Y4341
6Y-4341
6Y4341
BACKHOE LOADER, TELEHANDLER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 6Y4341:
Information:
Installation Of The Generator
For information or alignment of two bearing generators make reference to Form No. SEHS7073.Typical installation and alignment procedure for electric sets with single-bearing generators. Do not start the alignment procedure until the electric set is permanently installed. If the electric set is moved to a different location, check the alignment and make any corrections necessary. The alignment between the generator and the engine must be correct to get maximum performance and long life from the electric set.
REAR OF ENGINE
A. Pilot bore. B. Surface.1. Remove all dirt, burrs and paint from the contact surfaces of the generator supports and the base.
FRONT OF ENGINE
1. Indicator group. 2. Crankshaft pulley.Remove the protection material (compound) from the flywheel pilot bore (A) and from the surface (B) that makes contact with the coupling. All contact surfaces of the engine, coupling and generator must be completely clean.2. Remove the timing pointer cover from the flywheel housing. Install indicator group (1) as shown on the front of the engine with the tip of the indicator on the face of crankshaft pulley (2). Use a bar between the flywheel and flywheel housing to push the crankshaft toward the flywheel to remove all end play. Put the dial indicator in the "zero" position. Move the crankshaft to its most forward position, and make a record of the Total Indicator Reading (TIR). The TIR is the end play of the crankshaft.
FRONT OF GENERATOR
3. Plate assembly. 4. Shim pack.3. Put plate assembly (3) in position in the bore of the flywheel to check for clearance. There must be clearance between the outside diameter of the plate assembly (3) and the inside diameter of the bore in the flywheel.
Damage to the engine and/or generator can be the result if the electric set is run with a plate assembly that does not have this clearance.
4. Install a full shim pack (4) and plate assembly (3) on the generator with bolts (5). On D379, G379, D398, G398, D399 and G399 engines, tighten bolts (5) to a torque of 370 35 lb. ft. (505 45 N m). On all other engines, tighten bolts (5) to the standard torque.
INSTALL PLATE ASSEMBLY
5. Bolt.
ENGINE FLYWHEEL
6. Guide bolt.
PUT GENERATOR IN POSITION
INSTALL BOLTS
7. Bolt. 8. Bolt.5. Install guide bolt (6) in the flywheel. Put the generator in position on the engine, and install bolts (7) and (8). Tighten bolts (7) and (8) but do not bend the locks under bolts (8) at this time.6. Use a dial indicator (1) to check crankshaft end play (do not use force to hold the crankshaft in position). Remove the generator. Remove only enough shims to get the original amount of end play as shown in Step 2.
PUT BOLTS IN POSITION
9. Bolt. 10. Generator support.7. Install the generator and again check the crankshaft end play. After the correct amount of shims has been installed, bend the locks under bolts (8).8. Install but do not tighten all bolts (9) that fasten generator supports (10) to the base. To
For information or alignment of two bearing generators make reference to Form No. SEHS7073.Typical installation and alignment procedure for electric sets with single-bearing generators. Do not start the alignment procedure until the electric set is permanently installed. If the electric set is moved to a different location, check the alignment and make any corrections necessary. The alignment between the generator and the engine must be correct to get maximum performance and long life from the electric set.
REAR OF ENGINE
A. Pilot bore. B. Surface.1. Remove all dirt, burrs and paint from the contact surfaces of the generator supports and the base.
FRONT OF ENGINE
1. Indicator group. 2. Crankshaft pulley.Remove the protection material (compound) from the flywheel pilot bore (A) and from the surface (B) that makes contact with the coupling. All contact surfaces of the engine, coupling and generator must be completely clean.2. Remove the timing pointer cover from the flywheel housing. Install indicator group (1) as shown on the front of the engine with the tip of the indicator on the face of crankshaft pulley (2). Use a bar between the flywheel and flywheel housing to push the crankshaft toward the flywheel to remove all end play. Put the dial indicator in the "zero" position. Move the crankshaft to its most forward position, and make a record of the Total Indicator Reading (TIR). The TIR is the end play of the crankshaft.
FRONT OF GENERATOR
3. Plate assembly. 4. Shim pack.3. Put plate assembly (3) in position in the bore of the flywheel to check for clearance. There must be clearance between the outside diameter of the plate assembly (3) and the inside diameter of the bore in the flywheel.
Damage to the engine and/or generator can be the result if the electric set is run with a plate assembly that does not have this clearance.
4. Install a full shim pack (4) and plate assembly (3) on the generator with bolts (5). On D379, G379, D398, G398, D399 and G399 engines, tighten bolts (5) to a torque of 370 35 lb. ft. (505 45 N m). On all other engines, tighten bolts (5) to the standard torque.
INSTALL PLATE ASSEMBLY
5. Bolt.
ENGINE FLYWHEEL
6. Guide bolt.
PUT GENERATOR IN POSITION
INSTALL BOLTS
7. Bolt. 8. Bolt.5. Install guide bolt (6) in the flywheel. Put the generator in position on the engine, and install bolts (7) and (8). Tighten bolts (7) and (8) but do not bend the locks under bolts (8) at this time.6. Use a dial indicator (1) to check crankshaft end play (do not use force to hold the crankshaft in position). Remove the generator. Remove only enough shims to get the original amount of end play as shown in Step 2.
PUT BOLTS IN POSITION
9. Bolt. 10. Generator support.7. Install the generator and again check the crankshaft end play. After the correct amount of shims has been installed, bend the locks under bolts (8).8. Install but do not tighten all bolts (9) that fasten generator supports (10) to the base. To
Caterpillar SIS machinery equipment:
Caterpillar SIS
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 ENGINE »
6Y-4341
PUMP GP-CRESCENT
428B BACKHOE LOADER 7EJ00001-05999 (MACHINE) POWERED BY 3054 DIESEL ENGINE »
6Y-4341
PUMP GP-CRESCENT
436B BACKHOE LOADER 6MJ00001-UP (MACHINE) POWERED BY 3054 ENGINE »
6Y-4341
PUMP GP-CRESCENT
428B BACKHOE LOADER 3KK00001-02999 (MACHINE) POWERED BY 3054 ENGINE »
6Y-4341
PUMP GP-CRESCENT
438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIESEL ENGINE »
6Y-4341
PUMP GP-CRESCENT
426B BACKHOE LOADER 5YJ02300-UP (MACHINE) POWERED BY 3054 DIESEL ENGINE »
6Y-4341
PUMP GP-CRESCENT
436B BACKHOE LOADER 6MJ00800-UP (MACHINE) »
6Y-4341
PUMP GP-CRESCENT
Caterpillar parts catalog:
Parts pump Caterpillar catalog:
1003259
PUMP GP-PISTON
416B, 426B, 428B, 436B, 438B
416B, 426B, 428B, 436B, 438B
1514825
PUMP GP-WATER
3054, 307, 312, 315, 317, 416B, 416C, 426C, 428B, 428C, 436C, 438C, 914G, AP-800C, BG-225B, CB-434B, CB-544, CB-545, IT14G, TH62, TH63, TH82, TH83
3054, 307, 312, 315, 317, 416B, 416C, 426C, 428B, 428C, 436C, 438C, 914G, AP-800C, BG-225B, CB-434B, CB-544, CB-545, IT14G, TH62, TH63, TH82, TH83
4T6895
PUMP GP-PISTON
416, 428
416, 428
9T6857
PUMP GP-PISTON
416, 428
416, 428
9W5426
PUMP GP-CRESCENT (SHW CRESENT)
416, 426, 426B, 428, 436B, 438B, RT50
416, 426, 426B, 428, 436B, 438B, RT50
6I0253
PUMP AS-ENGINE OIL
3054, 3054B, 307, 416B, 416C, 416D, 424D, 428B, 428C, CB-434B, CB-434C, CB-544, CB-545, CP-433C, CS-323C, CS-431C, PS-150B, TH210, TH215, TH62, TH63, TH82
3054, 3054B, 307, 416B, 416C, 416D, 424D, 428B, 428C, CB-434B, CB-434C, CB-544, CB-545, CP-433C, CS-323C, CS-431C, PS-150B, TH210, TH215, TH62, TH63, TH82
6I0912
PUMP AS-ENGINE OIL
3054, 3054B, 312, 312B L, 312C, 315, 315B L, 317, 416B, 416C, 416D, 420D, 426C, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 554, 908, 914G, AP-800C, BG-225B, BG-225C, CB-434C, CB-534B, CB-53...
3054, 3054B, 312, 312B L, 312C, 315, 315B L, 317, 416B, 416C, 416D, 420D, 426C, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 554, 908, 914G, AP-800C, BG-225B, BG-225C, CB-434C, CB-534B, CB-53...
1213220
PUMP GP-FUEL TRANSFER
3054, 3054B, 307, 312, 312C, 315, 315B L, 317, 416B, 416C, 426C, 428B, 428C, 436C, 438C, 914G, AP-800C, BG-225B, CB-434B, CB-434C, CB-534B, CB-534C, CB-544, CB-545, CP-433C, CS-323C, CS-431C, IT14G, M...
3054, 3054B, 307, 312, 312C, 315, 315B L, 317, 416B, 416C, 426C, 428B, 428C, 436C, 438C, 914G, AP-800C, BG-225B, CB-434B, CB-434C, CB-534B, CB-534C, CB-544, CB-545, CP-433C, CS-323C, CS-431C, IT14G, M...
0676925
PUMP AS
206, RT50
206, RT50
4W2952
PUMP GP-WATER
212, 428
212, 428
7C2798
PUMP AS
428, RT50
428, RT50
2703546
PUMP & MTG GP-AUXILIARY
AP-600D, AP-655D
AP-600D, AP-655D
3522157
PUMP GP-WATER
3126, 3126B, 3126E, AP-755, C-9, C7, PM-102
3126, 3126B, 3126E, AP-755, C-9, C7, PM-102
2712244
PUMP GP-FUEL INJECTION
3512C, 785D
3512C, 785D
3254892
PUMP GP-FUEL INJECTION
3011C, C1.1
3011C, C1.1
7T3214
PUMP GP-GEAR
D3B, D3C
D3B, D3C
2362048
PUMP & MTG GP-HYDRAULIC
TH210, TH215
TH210, TH215
2690542
PUMP GP-PISTON
AP-600D, AP-655D
AP-600D, AP-655D
7C1208
PUMP GP-WATER
AP-1200
AP-1200
2115015
PUMP GP-VACUUM
564, 574B
564, 574B