7s7400 PUMP GP-SCAVENGE & CIRCULATING Caterpillar parts
583K, 594, 594H, D8H, D8K, D9G, D9H
Rating:
Alternative (cross code) number:
CA7s7400
7s-7400
7s7400
CA7s7400
7s-7400
7s7400
Weight: 33 pounds 14 kg.
PIPELAYER, TRACK-TYPE TRACTOR,
Related part:
7S7400
PUMP GP-SCAV
0R7806
R
7S7400
PUMP-GEAR TC-YM
2260173
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
7S7400 SCAVENGE OIL PUMP Suitable For Caterpillar 7S7400
KMP BRAND Suitable for Caterpillar
KMP BRAND Suitable for Caterpillar
7S7400 SCAVENGE OIL PUMP Suitable For Caterpillar 7S7400
KMP BRAND Suitable for Caterpillar
KMP BRAND Suitable for Caterpillar
Compatible equipment models: 7s7400:
Information:
Inspect the Engine for Leaks and for Loose Connections
A walk-around inspection should only take a few minutes. When the time is taken to perform these checks, costly repairs and accidents can be avoided.For maximum engine service life, thoroughly inspect the engine compartment before starting the engine. Look for items such as leaks, loose bolts, loose connections and trash buildup. Make repairs, as needed.
The guards must be in the proper place. Repair damaged guards or replace missing guards.
Wipe all caps and plugs before the engine is serviced in order to reduce the chance of system contamination.
For any type of leak (coolant, lube, or fuel) clean up the fluid. If leaking is observed, find the source and correct the leak. If leaking is suspected, check the fluid levels more often than recommended until the leak is found or fixed, or until the suspicion of a leak is proved to be unwarranted.
Accumulated grease and/or oil on an engine or deck is a fire hazard. Remove this debris with steam cleaning or high pressure water.
Ensure that cooling lines are properly clamped and tight. Check for leaks. Check the condition of all pipes.
Inspect the water pumps for coolant leaks.Note: The water pump seal is lubricated by coolant in the cooling system. It is normal for a small amount of leakage to occur when the engine cools and the parts contract.Excessive coolant leakage may indicate the need to replace the water pump seal. For the removal of water pumps and the installation of water pumps and/or seals, refer to the Service Manual for the engine or consult your Caterpillar dealer.
Inspect the lubrication system for leaks at the front crankshaft seal, the rear crankshaft seal, the oil pan, the oil filters and the valve cover.
Inspect the fuel system for leaks. Look for loose fuel line clamps.
Inspect the piping for the air inlet system and the elbows for cracks and for loose clamps.
Drain the water and the sediment from fuel tanks on a daily basis in order to ensure that only clean fuel enters the fuel system.
Inspect the wiring and the wiring harnesses for loose connections and for worn wires or frayed wires.
Inspect the ground strap for a good connection and for good condition.
Check the condition of the gauges. Replace any gauge that is damaged. Replace any gauge that can not be calibrated.
Inspect the exhaust system for leaks. Inspect the gaskets and the exhaust bellows joint. If a leak is found, make repairs.
A walk-around inspection should only take a few minutes. When the time is taken to perform these checks, costly repairs and accidents can be avoided.For maximum engine service life, thoroughly inspect the engine compartment before starting the engine. Look for items such as leaks, loose bolts, loose connections and trash buildup. Make repairs, as needed.
The guards must be in the proper place. Repair damaged guards or replace missing guards.
Wipe all caps and plugs before the engine is serviced in order to reduce the chance of system contamination.
For any type of leak (coolant, lube, or fuel) clean up the fluid. If leaking is observed, find the source and correct the leak. If leaking is suspected, check the fluid levels more often than recommended until the leak is found or fixed, or until the suspicion of a leak is proved to be unwarranted.
Accumulated grease and/or oil on an engine or deck is a fire hazard. Remove this debris with steam cleaning or high pressure water.
Ensure that cooling lines are properly clamped and tight. Check for leaks. Check the condition of all pipes.
Inspect the water pumps for coolant leaks.Note: The water pump seal is lubricated by coolant in the cooling system. It is normal for a small amount of leakage to occur when the engine cools and the parts contract.Excessive coolant leakage may indicate the need to replace the water pump seal. For the removal of water pumps and the installation of water pumps and/or seals, refer to the Service Manual for the engine or consult your Caterpillar dealer.
Inspect the lubrication system for leaks at the front crankshaft seal, the rear crankshaft seal, the oil pan, the oil filters and the valve cover.
Inspect the fuel system for leaks. Look for loose fuel line clamps.
Inspect the piping for the air inlet system and the elbows for cracks and for loose clamps.
Drain the water and the sediment from fuel tanks on a daily basis in order to ensure that only clean fuel enters the fuel system.
Inspect the wiring and the wiring harnesses for loose connections and for worn wires or frayed wires.
Inspect the ground strap for a good connection and for good condition.
Check the condition of the gauges. Replace any gauge that is damaged. Replace any gauge that can not be calibrated.
Inspect the exhaust system for leaks. Inspect the gaskets and the exhaust bellows joint. If a leak is found, make repairs.
Caterpillar SIS machinery equipment:
Caterpillar SIS
D8K TRACTOR / POWER SHIFT / 66V00001-02084 (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
D8K TRACTOR / POWER SHIFT / 66V02085-UP (MACHINE) POWERED BY D342 ENGINE »
7S-7400
GEAR PUMP GROUP
DUAL D9H TRACTOR 97V00001-UP (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
S X S D9H TRACTOR 12U00001-UP (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
D8K TRACTOR-- IF EQUIPPED WITH ARRANGEMENT 1Z413 77V04429-UP (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
D8K TRACTOR / POWERSHIFT / 77V05006-UP (MACHINE) POWERED BY D342 ENGINE »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
583 PIPELAYER / POWER SHIFT / 78V00535-UP (MACHINE) »
7S-7400
PUMP GP-SCAVENGE
D9H TRACTOR / POWER SHIFT / 90V04940-UP (MACHINE) POWERED BY D353 ENGINE »
7S-7400
PUMP GP-SCAVENGE
594H PIPELAYER / POWER SHIFT / 96V00255-UP (MACHINE) POWERED BY D353 ENGINE »
7S-7400
PUMP GP-SCAVENGE
D9H TRACTOR 90V00001-UP (MACHINE) POWERED BY D353 ENGINE »
7S-7400
SCAVENGE AND CIRCULATING PUMP GROUP
D9H TRACTOR - ARRANGEMENT 1Z434 / POWER SHIFT / 90V07190-UP (MACHINE) POWERED BY D353 ENGINE »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
594H PIPELAYER - ARRANGEMENT 1Z420 / POWER SHIFT / 96V00385-UP (MACHINE) POWERED BY D353 ENGINE »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
D8H TRACTOR / POWER SHIFT / 46A10725-24432 (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
D9G TRACTOR / POWER SHIFT / 66A03266-09417 (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
D9G TRACTOR / POWER SHIFT / 66A03266-09417 (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
594 PIPELAYER / POWER SHIFT / 62H00001-UP (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
594 PIPELAYER / POWER SHIFT / 62H00001-UP (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
DUAL D9G TRACTOR 90J00001-00092 (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
D9G TRACTOR 66A09418-12015 (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
D8H TRACTOR / POWER SHIFT / 46A24433-UP (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
D9G TRACTOR 66A12016-UP (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
594 PIPELAYER 62H00310-UP (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
DUAL D9G TRACTOR 90J00106-UP (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
D8K TRACTOR / POWERSHIFT / 77V00001-05005 (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
583K PIPELAYER 78V00001-00534 (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
594H PIPELAYER 96V00001-UP (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
D9H TRACTOR / POWER SHIFT / 90V00001-04939 (MACHINE) »
7S-7400
PUMP GP-SCAVENGE & CIRCULATING
Cat SIS web machinery list:
Parts pump Caterpillar catalog:
6N6802
PUMP AS-FUEL PRIMING
16, 594H, 769, 824B, 834, 988, D10, D9H
16, 594H, 769, 824B, 834, 988, D10, D9H
3G6002
PUMP GP-GEAR
193, D9H
193, D9H
3P4405
PUMP GP-TRANSMISSION GEAR
583K, 594H, D8K, D9H
583K, 594H, D8K, D9H
6N2450
PUMP GP-OIL
594H, D9H
594H, D9H
6N1813
PUMP GP-FUEL TRANSFER
594H, D9H
594H, D9H
9J5047
PUMP GP-VANE
572G, 583K
572G, 583K
2S7264
PUMP ASSEMBLY FUEL VALVE
594H, D353C, D379A, D379B, D398, D398A, D398B, D399, D9G, D9H
594H, D353C, D379A, D379B, D398, D398A, D398B, D399, D9G, D9H
8M2899
PUMP ASSEM.
D342C, D8H
D342C, D8H
6N6803
PUMP GROUP
657B, 777, 824B, D342, D8K
657B, 777, 824B, D342, D8K
5H1719
PUMP GROUP
D8H, D8K, D9E
D8H, D8K, D9E
4M1001
PUMP GROUP
594, D9G, D9H
594, D9G, D9H
8N0490
PUMP ASSEM.
963, 973, 992C, D10, D9H
963, 973, 992C, D10, D9H
6C3020
PUMP GP-REFUELING
225D, 229D, 231D
225D, 229D, 231D
3172659
PUMP GP-GEAR
797F
797F
1035695
PUMP GP-STEERING
CB-434B, CB-434C, CB-534B, CB-534C
CB-434B, CB-434C, CB-534B, CB-534C
9t1080
PUMP GP-VANE
D10N, D10R
D10N, D10R
1371339
PUMP GP-WATER
24H, 3412, 3412C, 3412D, 3412E, 5110B, 651E, 657E, 773B, 773D, 773E, 773F, 775D, 775E, 775F, 844, 844H, 990, 990 II, 990H, 992C, 992D, C27, C30, C32, D10N, D10R, D8L, D9L, D9N, D9R, G3412, G3412C, PM3...
24H, 3412, 3412C, 3412D, 3412E, 5110B, 651E, 657E, 773B, 773D, 773E, 773F, 775D, 775E, 775F, 844, 844H, 990, 990 II, 990H, 992C, 992D, C27, C30, C32, D10N, D10R, D8L, D9L, D9N, D9R, G3412, G3412C, PM3...
1G8599
PUMP GP-METERING
PM-201, PM-565, PM-565B
PM-201, PM-565, PM-565B
3796604
PUMP & MOUNTING GP
CS-54B
CS-54B
2919066
PUMP GP-WATER
3024C, C2.2
3024C, C2.2