2403396 PUSH ARM AS Caterpillar parts
D8R, D8T
Rating:
Alternative (cross code) number:
CA2403396
240-3396
2403396
CA2403396
240-3396
2403396
Weight: 978 pounds 443 kg.
TRACK-TYPE TRACTOR,
Number on catalog scheme:
4
For full view, you need register
Information:
Assembly Procedure
Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause problems in the future. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 1 g03230839
(1) Rectifier (2) Stator
Connect and solder the stator leads to the positive (+) diodes of rectifier (1) .
Illustration 2 g03230840
(1) Rectifier (2) Stator (3) Position wave washer
Position the insulators on the rectifier terminal studs. Position rectifier (1), and stator (2) into the rear frame, and install the three screws. Install the terminal insulators, washers, and nuts. Position wave washer (3) into the bearing bore of the rear frame.
Illustration 3 g03230842
(4) Rear bearing (5) Slip ring
Install slip ring (5) on the rotor. Connect and solder the rotor leads to the slip ring (5). Install rear bearing (4) .
Illustration 4 g03230845
(6) Bearing cover (7) Spacer (8) Front bearing
Install bearing cover (6), front bearing (8), and spacer (7) on the rotor.
Illustration 5 g03230846
(9) Rotor
Install rotor (9) and the four screws into the front frame.
Illustration 6 g03230848
(10) Stator assembly (11) Rotor assembly
Assemble front frame and rotor assembly (11) into rear frame and stator assembly (10). Make sure that the wave washer is fixed in the rear frame bearing bore. Align the front and rear frame marks made at disassembly for correct assembly. Install the four screws.
Illustration 7 g03230896
(12) Pulley (13) Fan
Install the key, fan (13), pulley (12), washer, and pulley nut. Tighten the nut to a torque of: 3E-7295 Charging Alternator Gp, and 9X-0341 Charging Alternator Gp ... 70 5 N m (52 4 lb ft) 8C-5535 Charging Alternator Gp, 7T-2876 Charging Alternator Gp, 2Y-4212 Charging Alternator Gp, and 2Y-8310 Charging Alternator Gp ... 35 10 N m (26 7 lb ft) 9W-3043 Charging Alternator Gp ... 50 5 N m (37 4 lb ft)
Illustration 8 g03230899
(14) Capacitor lead (15) Regulator
Install the capacitor and connect capacitor lead (14) to the back of the alternator.
Install regulator (15) .End By: Install the alternator on the machine. Refer to Disassembly and Assembly, "Alternator - Install" for the machine that is being serviced.
Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause problems in the future. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 1 g03230839
(1) Rectifier (2) Stator
Connect and solder the stator leads to the positive (+) diodes of rectifier (1) .
Illustration 2 g03230840
(1) Rectifier (2) Stator (3) Position wave washer
Position the insulators on the rectifier terminal studs. Position rectifier (1), and stator (2) into the rear frame, and install the three screws. Install the terminal insulators, washers, and nuts. Position wave washer (3) into the bearing bore of the rear frame.
Illustration 3 g03230842
(4) Rear bearing (5) Slip ring
Install slip ring (5) on the rotor. Connect and solder the rotor leads to the slip ring (5). Install rear bearing (4) .
Illustration 4 g03230845
(6) Bearing cover (7) Spacer (8) Front bearing
Install bearing cover (6), front bearing (8), and spacer (7) on the rotor.
Illustration 5 g03230846
(9) Rotor
Install rotor (9) and the four screws into the front frame.
Illustration 6 g03230848
(10) Stator assembly (11) Rotor assembly
Assemble front frame and rotor assembly (11) into rear frame and stator assembly (10). Make sure that the wave washer is fixed in the rear frame bearing bore. Align the front and rear frame marks made at disassembly for correct assembly. Install the four screws.
Illustration 7 g03230896
(12) Pulley (13) Fan
Install the key, fan (13), pulley (12), washer, and pulley nut. Tighten the nut to a torque of: 3E-7295 Charging Alternator Gp, and 9X-0341 Charging Alternator Gp ... 70 5 N m (52 4 lb ft) 8C-5535 Charging Alternator Gp, 7T-2876 Charging Alternator Gp, 2Y-4212 Charging Alternator Gp, and 2Y-8310 Charging Alternator Gp ... 35 10 N m (26 7 lb ft) 9W-3043 Charging Alternator Gp ... 50 5 N m (37 4 lb ft)
Illustration 8 g03230899
(14) Capacitor lead (15) Regulator
Install the capacitor and connect capacitor lead (14) to the back of the alternator.
Install regulator (15) .End By: Install the alternator on the machine. Refer to Disassembly and Assembly, "Alternator - Install" for the machine that is being serviced.
Caterpillar parts catalog:
Parts push Caterpillar catalog:
2394224
PUSH ARM GP
D8R, D8T
D8R, D8T
2403395
PUSH ARM GP
D8R, D8T
D8R, D8T
4173722
PUSH ARM GP
D8R, D8T
D8R, D8T
1586394
PUSH ARM GP-STABILIZER
D8R, D8R II
D8R, D8R II
2374368
PUSH ARM GP-STABILIZER
D8R, D8T
D8R, D8T
4173721
PUSH ARM GP-STABILIZER
D8R, D8T
D8R, D8T
2470851
PUSH ARM GP-STABILIZER
D8R, D8T
D8R, D8T
1060786
PUSH ARM AS-LH
D8N, D8R, D8R II
D8N, D8R, D8R II
8E6169
PUSH ARM AS-RH
D8N, D8R, D8R II
D8N, D8R, D8R II
1586395
PUSH ARM AS
D8R, D8R II
D8R, D8R II
2394215
PUSH ARM AS
D8R, D8T
D8R, D8T
2394225
PUSH ARM AS
D8R, D8T
D8R, D8T
2394225
PUSH ARM AS
D8R, D8T
D8R, D8T
2394215
PUSH ARM AS
D8R, D8T
D8R, D8T
4T8872
PUSH ARM AS
834B
834B
4T8871
PUSH ARM AS
834B
834B
1162431
PUSH ARM AS
825G, 825G II, 825H, 825K
825G, 825G II, 825H, 825K
1162430
PUSH ARM AS
825G, 825G II, 825H, 825K
825G, 825G II, 825H, 825K
1515219
PUSH ARM AS
854G, 854K
854G, 854K
1515218
PUSH ARM AS
854G, 854K
854G, 854K
3077616
PUSH ARM AS
D7R, D7R II
D7R, D7R II
1469644
PUSH ARM AS
D7R, D7R II
D7R, D7R II
1361976
PUSH ARM AS
D7R, D7R II
D7R, D7R II
1361974
PUSH ARM AS
D7R, D7R II
D7R, D7R II