3430919 PUSH ARM AS Caterpillar parts
D8T
Rating:
Alternative (cross code) number:
CA3430919
343-0919
3430919
CA3430919
343-0919
3430919
Weight: 934 pounds 423 kg.
TRACK-TYPE TRACTOR,
Compatible equipment models: 3430919:
Number on catalog scheme:
4
For full view, you need register
Information:
View L-L
Illustration 10 g00282575
Note: This view is for the right side of the machine. The view for the left side of the machine is the reverse of this view.
Apply 7M-7456 Compound to the bore before installing seals (30) .
Make sure that the OD of the collets, ID of the collets and the mating surfaces of the collets are clean. Apply 5P-3931 Thread Compound to the ID of the collets (29). Apply 5P-3931 Thread Compound to the bolt thread (28) .
Tighten the bolt (28) to a torque of 1800 200 N m (1330 150 lb ft). Strike the collets until the torque on the bolt is less than 950 N m (700 lb ft).
Tighten the bolt to a torque of 1800 200 N m (1330 150 lb ft). Strike the collets until the torque on the bolt is less than 1600 N m (1180 lb ft).
Tighten the bolt to a torque of 1800 200 N m (1330 150 lb ft).
Do step 7 for an optional installation procedure.
Install the pins and collets. Press the collets to the pin with a 507,000 N (114,000 lb) force. Install the bolt. Tighten the bolt to a torque of 1800 200 N m (1330 150 lb ft).
After 50 hours of operation, apply a torque of 1800 200 N m (1330 150 lb ft) to the bolt (28) .
Table 1
Linkage Pins and Bearing Sizes
View Pin Length Pin Diameter Diameter of Bore for Bearing
A-A
590.0 1.5 mm (23.23 0.06 inch)
203.200 0.038
Illustration 10 g00282575
Note: This view is for the right side of the machine. The view for the left side of the machine is the reverse of this view.
Apply 7M-7456 Compound to the bore before installing seals (30) .
Make sure that the OD of the collets, ID of the collets and the mating surfaces of the collets are clean. Apply 5P-3931 Thread Compound to the ID of the collets (29). Apply 5P-3931 Thread Compound to the bolt thread (28) .
Tighten the bolt (28) to a torque of 1800 200 N m (1330 150 lb ft). Strike the collets until the torque on the bolt is less than 950 N m (700 lb ft).
Tighten the bolt to a torque of 1800 200 N m (1330 150 lb ft). Strike the collets until the torque on the bolt is less than 1600 N m (1180 lb ft).
Tighten the bolt to a torque of 1800 200 N m (1330 150 lb ft).
Do step 7 for an optional installation procedure.
Install the pins and collets. Press the collets to the pin with a 507,000 N (114,000 lb) force. Install the bolt. Tighten the bolt to a torque of 1800 200 N m (1330 150 lb ft).
After 50 hours of operation, apply a torque of 1800 200 N m (1330 150 lb ft) to the bolt (28) .
Table 1
Linkage Pins and Bearing Sizes
View Pin Length Pin Diameter Diameter of Bore for Bearing
A-A
590.0 1.5 mm (23.23 0.06 inch)
203.200 0.038
Caterpillar parts catalog:
Parts push Caterpillar catalog:
3356685
PUSH ARM AS
D7R II
D7R II
3126540
PUSH ARM AS
D7E LGP
D7E LGP
3620275
PUSH ARM AS
D11T
D11T
3620274
PUSH ARM AS
D11T
D11T