AVSPARE.COM
parts catalog

PUSH AR-SNOW 5088325 - Caterpillar



5088325 PUSH AR-SNOW Caterpillar parts PUSH
Rating:
16
Alternative (cross code) number:
CA5088325
508-8325
5088325
Caterpillar 5088325 PUSH AR-SNOW
Weight: 2689 pounds 1219 kg.

Buy PUSH AR-SNOW 5088325 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme:
 
  For full view, you need register

Information:

Introduction
This Special Instruction explains the procedure for adjusting the slide frame for the seat. Do not begin the procedure until you have read the information that is contained in this instruction.Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools in order to perform these functions properly.Refer to the appropriate Parts Manual, Operation and Maintenance Manual, Disassembly and Assembly Manual, and Service Manual.Safety precautions and warnings are provided in the manuals and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Refer to the Operation and Maintenance Manual for your machine.
Park the machine on a smooth, level surface. Move away from other operating machines and away from personnel.
Permit only one operator on the machine. Keep other personnel away from the machine or in the operator's sight.
Lower the implements to the ground.Adjustment Procedure
When the forward and the rearward slide becomes loose, follow the steps below in order to tighten the slide and remove the looseness from the assembly.
Table 1
Affected Parts    
Part Number     Description    
314-4288     Suspension Seat Gp    
314-4289     Suspension Seat Gp    
314-4290     Suspension Seat Gp    
314-4291     Suspension Seat Gp    
Illustration 1 g01487437
Locate the slide plate. The slide plate is on the left hand side of the seat.
Illustration 2 g01487495
Locate the two access holes on the slide plate. The two access holes are used in order to allow tightening.
Illustration 3 g01487504
Slide the seat forward and slide the seat rearward in order to align the access holes with the gold colored screw.
Illustration 4 g01487539
Use a 1/8th allen wrench to tighten the screw. Tightening the screw forces the plastic block of the slide outward. Forcing the block outward takes up the free play within the slide assembly. Tighten the screws by a quarter of a turn at a time and try the slide until all the free play has been removed.
Illustration 5 g01487554
Overtightening will lock the slide assembly. The assembly should not exceed a force of 89 22 N (20 5 lb) in order to slide in the forward or rearward direction. To check, lift the handle for the slide and pull the seat forward. Use a gauge to measure pulling force.
Repeat the tightening procedure to obtain force of 89 22 N (20 5 lb).
Loosen the screws by a quarter of a turn at a time if the force is greater than 89 22 N (20 5 lb). Obtain a force of 89 22 N (20 5 lb).

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts push Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.