1436585 PUSHROD Caterpillar parts
3406E, 735, 740, 834G, 988G, C-15, C-16, C-18, C15, C16, C18, D350E II, D400E II
Rating:
Alternative (cross code) number:
CA1436585
143-6585
1436585
CA1436585
143-6585
1436585
Weight: 0.12 pounds 0 kg.
ARTICULATED TRUCK, WHEEL LOADER,
Compare Prices:
As an associate, we earn commssions on qualifying purchases through the links below
£6.79
01 Sep 2017
MS Autoteile: MS Autoteile
MS Autoteile 1436585 Fuel Filter
IPPON Fuel Filter Mitsubishi Colt new Colt III 3 IV 4
IPPON Fuel Filter Mitsubishi Colt new Colt III 3 IV 4
Number on catalog scheme:
22
For full view, you need register
Compatible equipment models: 1436585:
Cat SIS web machinery list:
Information:
Remove Fuel Injection Nozzles
Before removing or disconnecting a fuel line, clean the cylinder head area around the fuel line connection.1. Disconnect the fuel line from the injection nozzle using the one-hand, two-wrench squeeze method.
TWO-WRENCH SQUEEZE METHOD2. Remove the injection nozzle clamp (2).3. Lift the injection nozzle (3) out of the cylinder head.
Pull nozzle straight out, by hand, to remove. Slight twisting action is permissible if necessary. Never attempt to pry out a nozzle with a screwdriver or other similar tool.
INJECTION NOZZLE REMOVAL (Left side illustrated)
1. Lines (eight, four each side). 2. Clamps (eight, four each side). 3. Injection nozzles (eight, four each side).4. Use needle-nose pliers to remove carbon seal dam (5). Always install a new compression seal (4) and carbon seal dam (5) before installing injection nozzle.
REMOVING CARBON SEAL DAM
4. Compression seal. 5. Carbon seal dam.Install Fuel Injection Nozzles
1. Be sure the bore in the cylinder head, fuel inlet fittings and the gasket surfaces are clean. Dirt or burrs on gasket surfaces can cause body distortion, resulting in a sticking valve.
Never install an injection nozzle that has been dropped, without first testing it with the 8S2242 Nozzle Tester Group. The injector tips are very hard and brittle and break easily.
2. Install a new compression seal and carbon seal dam. Use carbon seal dam installation tool (6) to install the carbon seal dam.
INSTALLING CARBON SEAL DAM
6. 8S2252 Carbon Seal Dam Installation Tool. Install a new grommet (7) before reinstalling an injection nozzle.3. Lubricate the exterior surface of cap (8). Pull grommet (7) over cap (8) in the direction indicated by the arrows.4. The shaded area shows grommet (7) correctly installed: Rotate grommet (7) so the flat surface will face the valve cover when nozzle is installed into cylinder head.
INJECTION NOZZLE
7. Grommet. 8. Protective cap. 9. Protective cap. A. Groove in grommet. Groove (A) to be installed in the half-moon cut-out provided in the valve cover mounting pad of the cylinder head.5. Coat groove (A) of grommet (7) with 7M7260 Liquid Gasket. Remove caps (8) and (9) and install nozzle (3) into cylinder head using a twisting motion. Do not use lubricant in the cylinder head bore or on the nozzle body.
Do not bend the injector inlet connection when installing injector into cylinder head. Bending of the inlet connection creates tension on the injector and causes binding of the needle in the guide.
INSTALLING NOZZLE
2. Clamps (eight, four each side). 3. Injection nozzles (eight, four each side).6. Assemble and tighten clamp (2) to hold nozzle (3) in place. Connect fuel lines to nozzle (3) and hand tighten connector nuts.7. Install rocker arm assembly. Install retaining bolts and locks. Tighten bolts to 18 5 lb. ft. (2.5 0.7 mkg) and bend locks. Install fuel return manifold.8. Adjust the intake valve clearance to .015 in. (0.38 mm) and the exhaust valve clearance to .025 in. (0.64 mm).9. Install valve cover. Install mounting bolts and tighten to 120 24 lb. in. (138 28 cm.kg).10. Purge fuel lines of air
Before removing or disconnecting a fuel line, clean the cylinder head area around the fuel line connection.1. Disconnect the fuel line from the injection nozzle using the one-hand, two-wrench squeeze method.
TWO-WRENCH SQUEEZE METHOD2. Remove the injection nozzle clamp (2).3. Lift the injection nozzle (3) out of the cylinder head.
Pull nozzle straight out, by hand, to remove. Slight twisting action is permissible if necessary. Never attempt to pry out a nozzle with a screwdriver or other similar tool.
INJECTION NOZZLE REMOVAL (Left side illustrated)
1. Lines (eight, four each side). 2. Clamps (eight, four each side). 3. Injection nozzles (eight, four each side).4. Use needle-nose pliers to remove carbon seal dam (5). Always install a new compression seal (4) and carbon seal dam (5) before installing injection nozzle.
REMOVING CARBON SEAL DAM
4. Compression seal. 5. Carbon seal dam.Install Fuel Injection Nozzles
1. Be sure the bore in the cylinder head, fuel inlet fittings and the gasket surfaces are clean. Dirt or burrs on gasket surfaces can cause body distortion, resulting in a sticking valve.
Never install an injection nozzle that has been dropped, without first testing it with the 8S2242 Nozzle Tester Group. The injector tips are very hard and brittle and break easily.
2. Install a new compression seal and carbon seal dam. Use carbon seal dam installation tool (6) to install the carbon seal dam.
INSTALLING CARBON SEAL DAM
6. 8S2252 Carbon Seal Dam Installation Tool. Install a new grommet (7) before reinstalling an injection nozzle.3. Lubricate the exterior surface of cap (8). Pull grommet (7) over cap (8) in the direction indicated by the arrows.4. The shaded area shows grommet (7) correctly installed: Rotate grommet (7) so the flat surface will face the valve cover when nozzle is installed into cylinder head.
INJECTION NOZZLE
7. Grommet. 8. Protective cap. 9. Protective cap. A. Groove in grommet. Groove (A) to be installed in the half-moon cut-out provided in the valve cover mounting pad of the cylinder head.5. Coat groove (A) of grommet (7) with 7M7260 Liquid Gasket. Remove caps (8) and (9) and install nozzle (3) into cylinder head using a twisting motion. Do not use lubricant in the cylinder head bore or on the nozzle body.
Do not bend the injector inlet connection when installing injector into cylinder head. Bending of the inlet connection creates tension on the injector and causes binding of the needle in the guide.
INSTALLING NOZZLE
2. Clamps (eight, four each side). 3. Injection nozzles (eight, four each side).6. Assemble and tighten clamp (2) to hold nozzle (3) in place. Connect fuel lines to nozzle (3) and hand tighten connector nuts.7. Install rocker arm assembly. Install retaining bolts and locks. Tighten bolts to 18 5 lb. ft. (2.5 0.7 mkg) and bend locks. Install fuel return manifold.8. Adjust the intake valve clearance to .015 in. (0.38 mm) and the exhaust valve clearance to .025 in. (0.64 mm).9. Install valve cover. Install mounting bolts and tighten to 120 24 lb. in. (138 28 cm.kg).10. Purge fuel lines of air
Parts pushrod Caterpillar catalog:
3406E, 834G, 988G, C-15, C-16, D350E II, D400E II
3406E, 735, 740, 834G, 988G, C-15, C-16, C-18, C15, C16, C18, D350E II, D400E II
3406E, 834G, 988G, C-15, C-16, D350E II, D400E II
3306, 3306C
14M, 16M, 345C, 345C L, 345C MH, 725, 730, 966H, 972H, C11, C13, CX31-C13I, RM-300, TH35-C13I, W345C MH
14M, 16M, 345C, 345C L, 345C MH, 725, 730, 966H, 972H, C11, C13, CX31-C13I, RM-300, TH35-C13I, W345C MH
938H, 953D, AP1000E, C4.4, C6.6, C7.1, D6K LGP, D6N, PL61
14M, 16M, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 725, 730, 730C, 966H, 972H,...
1566955
PUSHROD
3013, 302.5, CB-214D, CB-334D, CB-335D
3013, 302.5, CB-214D, CB-334D, CB-335D
2W7047
PUSHROD AS
G3304, G3304B, G3306
G3304, G3304B, G3306
3813638
PUSHROD
3.4B IOPU, 311F LRR, C3.4B, CB-44B, CB-54B, CD-54B, CW-14
3.4B IOPU, 311F LRR, C3.4B, CB-44B, CB-54B, CD-54B, CW-14
1799542
PUSHROD
3612, G3606, G3612, G3616
3612, G3606, G3612, G3616
3406E, 735, 740, 834G, 988G, C-15, C-16, C-18, C15, C16, C18, D350E II, D400E II
1192915
PUSHROD
3116
3116