RADIATOR GP 1301852 - Caterpillar

1301852 RADIATOR GP Caterpillar parts CB-534B, CB-534C, CB-535B, CP-433C, CS-431C, CS-433C, PF-290B, PS-200B, PS-300B, PS-360B

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1301852
130-1852
1301852

Weight: 88 pounds 40 kg.

Information:

CORE DEPTH 114.3 mm

CORE HEIGHT 584.2 mm

CORE WIDTH 587.4 mm

FIN DENSITY 10.5

HEIGHT BOTTOM TANK 88.9 mm

HEIGHT OF TOP TANK 139.7 mm

NUMBER OF TUBE ROWS 6

Buy RADIATOR GP 1301852 Caterpillar genuine, new aftermarket tractor parts with delivery
PNEUMATIC COMPACTOR, VIBRATORY COMPACTOR,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

$17.95

14 Sep 2021

US: Empire Rigging

DIXON 2VEP/VEP2 Body Seal (130185-2)
Dixon

This part in 1 request: Show. This information for suppliers only!

#313017 1301852

2019-05-21

Number on catalog scheme: 1

Caterpillar 1301852 Parts scheme RADIATOR GP

For full view, you need register

Compatible equipment models: 1301852:

PNEUMATIC COMPACTOR PF-290B PS-200B PS-300B PS-360B

VIBRATORY COMPACTOR CB-534B CB-534C CB-535B CP-433C CS-431C CS-433C Caterpillar

Information:

Introduction
Two relief valves are located in the head of the swing motor. These relief valves limit the pressure in the left and right swing circuits to the swing relief valve settings. The following procedure will determine if the swing relief valves are out of adjustment.Required Tools
Illustration 1 g02571852
Tooling (A)
198-4240 Digital Pressure Indicator Gp
Table 2
Tool Item Qty Part Number Description
A 198-4240 Digital Pressure Indicator Gp
A1 1 198-4234 Indicator
A2 1 198-4239 Pressure Sensor 41,368 kPa (6,000 psi)
A3 1 198-4236 Extension Cable Machine Preparation
Position the machine on level ground and stop the engine.
Release the pressure in the hydraulic system. Refer to Testing and Adjusting, "System Pressure - Release".
Illustration 2 g03882219
Pump compartment
(1) Pressure tap (delivery pressure for drive pump)
(2) Pressure tap (delivery pressure for idler pump)
(3) Pressure tap (power shift pressure)
Attach a 41,368 kPa (6,000 psi) pressure sensor to pressure tap (2).
Illustration 3 g03882243
Pilot manifold
(4) Solenoid valve for the swing parking brake
(5) Connector
Disconnect connector (5) from the solenoid valve for swing parking brake (4). Test Procedure
Start the engine.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Place the machine controls at the following settings: engine speed dial "10" and AEC switch OFF. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for engine rpm settings.
Place the hydraulic activation control lever in the UNLOCKED position.
Move the swing joystick slowly and ensure that the swing parking brake is operating properly.
Illustration 4 g03882254
Swing motor
(6) Adjustment plug
(7) Locknut
(8) Relief valve (right swing)
(9) Adjustment plug
(10) Locknut
(11) Relief valve (left swing)
Slowly move the swing joystick for a full SWING RIGHT operation and check the pressure for relief valve (8) at pressure tap (2).
Return the swing joystick to the NEUTRAL position.
The pressure setting of the swing relief valve is 31400 + 1000 - 1500 kPa (4554 + 145 - 218 psi). If the pressure reading at pressure tap (2) is not within the specification, adjust the swing relief valve.
In order to adjust the swing relief valve, loosen locknut (7). Turn adjustment plug (6) until the pressure sensor reading at pressure tap