1403632 RADIATOR AS Caterpillar parts
416C, 426C, 428C
Rating:
Alternative (cross code) number:
CA1403632
140-3632
1403632
CA1403632
140-3632
1403632
Weight: 33 pounds 14 kg.
Information:
CORE DEPTH
104.8
mm
CORE HEIGHT
570
mm
CORE WIDTH
551.7
mm
FIN DENSITY
7.5
HEIGHT BOTTOM TANK
0
mm
HEIGHT OF TOP TANK
0
mm
NUMBER OF TUBE ROWS
3
HEAT REJECTION
56.06KW50C
BACKHOE LOADER,
Information:
Illustration 1 g02716744
Schematic of the Winch Spool In SolenoidThis diagnostic code is associated with the Winch Spool In Solenoid. The FMI 03 means that the ECM has determined that the voltage of the solenoid circuit is above normal.The possible causes of this diagnostic code are listed:
The energize circuit of the solenoid is shorted to the +battery circuit.
The ECM has failed. This is unlikely.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 3191 FMI 03 is active before performing this procedure.Note: Use a Digital Multimeter for the measurements in the procedure.System Response:A level 2 warning will be generated.Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO THE +BATTERY CIRCUIT.
Turn the key start switch and the disconnect switch to the ON position.Note: Use a wire removal tool to remove the appropriate wires from the machine harness connector for the ECM.
Remove the wire for the solenoid signal (F869-PK) from the connector contact 26 for the implement ECM.
Measure the voltage from the wire for the solenoid signal (F869-PK) to frame ground.
Remove the wire for the solenoid return (J807-BK) from the connector contact 27 for the implement ECM.
Measure the voltage from the wire for the solenoid return (J807-BK) to frame ground.Expected Result:The voltage is 0 VDC.Results:
OK - The voltage is 0 VDC. There are no shorts in the wires. Proceed to test step 2.
NOT OK - There is a voltage present in a wire. The short is in the wire with a measured voltage. The machine harness has failed.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Determine if the CID 3191 FMI 03 is active.Expected Result:The CID 3191 FMI 03 is active.Results:
YES - The CID 3191 FMI 03 is active. The problem has not been corrected. The ECM may have failed.Repair: If the cause of the problem is not found, contact the Technical Communicator for your dealership for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the ECM requires replacement, see Troubleshooting, "Electronic Control Module (ECM) - Replace".STOP
NO - The CID 3191 FMI 03 is not active. The problem does not exist at this time.Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was
Caterpillar parts catalog:
Parts radiator Caterpillar catalog:
1442218
RADIATOR & HYD OIL COOLER GP
416C, 426C, 428C, 436C, 438C
416C, 426C, 428C, 436C, 438C
1471557
RADIATOR & HYD OIL COOLER GP
416C, 416D, 420D, 424D, 426C, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D
416C, 416D, 420D, 424D, 426C, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D
1543796
RADIATOR GP
416C, 426C, 428C
416C, 426C, 428C
1456716
RADIATOR GP
416C, 426C, 428C
416C, 426C, 428C
7E4632
RADIATOR GP
416C, 428C
416C, 428C
1442220
RADIATOR & HYD OIL COOLER GP
416C, 426C, 428C, 436C, 438C
416C, 426C, 428C, 436C, 438C
7E4633
RADIATOR GP
416C, 426C, 428C, 436C, 438C
416C, 426C, 428C, 436C, 438C
1276981
RADIATOR GP
416C, 426C, 428C, 436C, 438C
416C, 426C, 428C, 436C, 438C
1403633
RADIATOR AS
416C, 426C, 428C, 436C, 438C
416C, 426C, 428C, 436C, 438C
1403634
RADIATOR AS
416C, 416D, 420D, 424D, 426C, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D
416C, 416D, 420D, 424D, 426C, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D
7E4638
RADIATOR AS
416C, 428C
416C, 428C
7E4639
RADIATOR AS
416C, 426C, 428C, 436C, 438C
416C, 426C, 428C, 436C, 438C
7E4639
RADIATOR AS
416C, 426C, 428C, 436C, 438C
416C, 426C, 428C, 436C, 438C
7E4638
RADIATOR AS
416C, 428C
416C, 428C
1403634
RADIATOR AS
416C, 416D, 420D, 424D, 426C, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D
416C, 416D, 420D, 424D, 426C, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D
1403633
RADIATOR AS
416C, 426C, 428C, 436C, 438C
416C, 426C, 428C, 436C, 438C
1437698
RADIATOR
TH103
TH103
1296225
RADIATOR
TH103
TH103
2105948
RADIATOR GP
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E, 444E
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E, 444E
2066775
RADIATOR GP
TH220B, TH330B, TH460B, TH560B, TH580B
TH220B, TH330B, TH460B, TH560B, TH580B
2066774
RADIATOR GP
TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
2152272
RADIATOR
TH210, TH215
TH210, TH215
1428879
RADIATOR & HYD OIL COOLER AS
236, 248, 267, 287, CB-434D
236, 248, 267, 287, CB-434D
1428861
RADIATOR & HYD OIL COOLER AS
216, 228, 236, 247, 267
216, 228, 236, 247, 267