AVSPARE.COM
parts catalog

RADIATOR GP 2340176 - Caterpillar


2340176 RADIATOR GP Caterpillar parts 914G, IT14G
Rating:
19
Alternative (cross code) number:
CA2340176
234-0176
2340176
Caterpillar 2340176 RADIATOR GP

Buy RADIATOR GP 2340176 Caterpillar genuine, new aftermarket tractor parts with delivery
COMPACT WHEEL LOADER, INTEGRATED TOOLCARRIER,

Compatible equipment models: 2340176:

COMPACT WHEEL LOADER  914G  
INTEGRATED TOOLCARRIER  IT14G   Caterpillar
Number on catalog scheme: 2
  For full view, you need register

Information:


Table 2
Switch Operation For the Quick Coupler Switch (Wedge Lock) CID 1529
Contacts Switch State Continuity
1, 2 Engage Yes
1, 2 Retract No
2, 3 Engage No
2, 3 Retract Yes
Table 3
Switch Operation For the Quick Coupler Switch (Pin Lock) CID 1529
Contacts Switch State Continuity
1, 2 Engage Yes
1, 2 Neutral No
1, 2 Retract No
2, 3 Engage No
2, 3 Neutral No
2, 3 Retract Yes Note: The diagram above is a simplified schematic of the ECM switch connections. The schematic is electrically correct, however, not all of the possible harness connectors are shown. Refer to the latest revision of Electrical Schematic, UENR0290 for the complete schematic.
Table 4
Troubleshooting Test Steps Values Results
1. Identify Active FMI Code Associated With Sensor Circuit
Code present. FMI 3 diagnostic code, proceed to Test Step 2.
FMI 4 diagnostic code, proceed to Test Step 4.
FMI 7 diagnostic code, proceed to Test Step 8.
Begin Process For FMI 3 Troubleshooting HERE
2. Check The Circuit For A Short
A. Turn the keyswitch OFF.
B. Disconnect the switch from the machine harness.
C. Disconnect the J1 and J2 machine harness connections from the Machine ECM.
C. At the machine harness connector for the ECM, one at a time, measure the resistance between each of the signal contacts to every other contact used in the J1 and J2 machine harness connectors.
The resistance is greater than 5 K Ω. OK - The resistance is correct.
Proceed to Test Step 3.
NOT OK - The resistance check is not correct.
Repair: There is a short in the signal circuits of the machine harness. Repair or replace the machine harness.
STOP
3. Check the Operation of the Switch.
A. The keyswitch remains OFF.
B. Reconnect all harness connectors.
C. Check the operation of the switch. Refer to the table for the suspected faulty switch at the beginning of this procedure for switch operation.
The switch operates correctly. OK - The switch is operating correctly.
Proceed to Test Step 10.
NOT OK - The switch is not operating correctly. The switch has failed
Repair: Replace the switch.
STOP
Begin Process For FMI 4 Troubleshooting HERE
4. Check the Harness For an Open
A. Turn key start switch and disconnect switch OFF.
B. Disconnect the switch from the machine harness.
C. Disconnect the J1 and J2 machine harness connector.
D. At the machine harness connector for the switch, place a jumper wire between the signal contacts.
E. At the machine harness connect for the ECM, measure the resistance between the signal contacts.
The resistance is less than 5 Ω. OK - The circuit is correct.
Proceed to Test Step 5.
NOT OK - The resistance is

Caterpillar parts catalog:

Caterpillar parts catalog
IT14G Integrated Tool Carrier FWL00001-UP (MACHINE) POWERED BY 3054C Engine
914G Wheel Loader PDF00001-UP (MACHINE) POWERED BY 3054C Engine


Parts radiator Caterpillar catalog:

2349753 RADIATOR GP
914G, IT14G, IT14G2
2566228 RADIATOR GP
914G, IT14G, IT14G2
3777572 RADIATOR GP
906H2, 907H2, 908H2
2654644 RADIATOR GP
906H, 907H, 908H
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.