1700558 REBUILD KIT Caterpillar parts
Rating:
Alternative (cross code) number:
CA1700558
170-0558
1700558
CA1700558
170-0558
1700558
Weight: 2 pounds 1 kg.
Related part:
1700558
REBUILD KT-YM
3901001
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Replacement for fits 1700558 Rebuild Kit Fits Caterpillar Models
SLLOPLUS
SLLOPLUS
$413.30
25 Jun 2024
3.88[1.75] Pounds
US: Global Power
SKF LARGE DIAMETER SEAL (#1700558)
SKF SKF LARGE DIAMETER SEAL (#1700558)
SKF SKF LARGE DIAMETER SEAL (#1700558)
$427.10
05 Mar 2024
3.88[1.75] pounds
US: Global Power
SKF LARGE DIAMETER SEAL (#1700558)
SKF SKF LARGE DIAMETER SEAL (#1700558)
SKF SKF LARGE DIAMETER SEAL (#1700558)
For full view, you need register
Information:
Installation Procedure
All plugs and caps must be remain in position until the component is about to be installed
Rotate gear on the fuel injection pump in order to align the timing marks. Align the timing marks, refer to Systems Operation Testing and Adjusting, "Fuel Injection Timing - Check" for more information.
Illustration 1 g03850301
Illustration 2 g03818192
Illustration 3 g03818187
Install new O-ring (22) to fuel injection pump assembly (10).
Install fuel injection pump assembly (10) to the front housing. Ensure that the timing mark on the fuel injection pump gear and the camshaft gear are aligned as shown in Illustration 2.
Install bolts (13), (14), (16), (17), (18), (19), and (20). Install nut (15). Tighten nut (15) and bolts (13), (14), (16), (17), (18), and (19) to a torque of 10 N m (88 lb in).
Install new fuel line (7) and tighten nuts (6) and (8) to a torque of 23 N m (204 lb in). Note: If the high-pressure fuel line clamp was repositioned during disassembly, return the clamp to the original position.
Install banjo bolt (9) with new sealing washer (not shown) and tighten the bolt to a torque of 13 N m (115. lb in).
Connect the fuel hose assembly to fuel inlet (21).
Reconnect the harness assembly to fuel temperature sensor (12) and fuel solenoid (11).
Illustration 4 g03819043
If necessary, replace O ring seal (4). Install O ring seal (4) into cover (5).
Install plate (3) and clip (2) complete with harness. Install bolts (1) and tighten to a torque of 26 N m (230 lb in).
Install the fuel filter base, refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install" for the correct procedure.
Turn the fuel supply to the ON position. Turn the battery disconnect switch to the ON position.
Prime the fuel system, refer to Operation and Maintenance Manual, "Fuel system - Prime".
After replacement of the fuel injection pump, the fuel injection pump must be calibrated in order to prevent damage to the fuel system. Use the electronic service tool to perform "Fuel Pump Learn".
All plugs and caps must be remain in position until the component is about to be installed
Rotate gear on the fuel injection pump in order to align the timing marks. Align the timing marks, refer to Systems Operation Testing and Adjusting, "Fuel Injection Timing - Check" for more information.
Illustration 1 g03850301
Illustration 2 g03818192
Illustration 3 g03818187
Install new O-ring (22) to fuel injection pump assembly (10).
Install fuel injection pump assembly (10) to the front housing. Ensure that the timing mark on the fuel injection pump gear and the camshaft gear are aligned as shown in Illustration 2.
Install bolts (13), (14), (16), (17), (18), (19), and (20). Install nut (15). Tighten nut (15) and bolts (13), (14), (16), (17), (18), and (19) to a torque of 10 N m (88 lb in).
Install new fuel line (7) and tighten nuts (6) and (8) to a torque of 23 N m (204 lb in). Note: If the high-pressure fuel line clamp was repositioned during disassembly, return the clamp to the original position.
Install banjo bolt (9) with new sealing washer (not shown) and tighten the bolt to a torque of 13 N m (115. lb in).
Connect the fuel hose assembly to fuel inlet (21).
Reconnect the harness assembly to fuel temperature sensor (12) and fuel solenoid (11).
Illustration 4 g03819043
If necessary, replace O ring seal (4). Install O ring seal (4) into cover (5).
Install plate (3) and clip (2) complete with harness. Install bolts (1) and tighten to a torque of 26 N m (230 lb in).
Install the fuel filter base, refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install" for the correct procedure.
Turn the fuel supply to the ON position. Turn the battery disconnect switch to the ON position.
Prime the fuel system, refer to Operation and Maintenance Manual, "Fuel system - Prime".
After replacement of the fuel injection pump, the fuel injection pump must be calibrated in order to prevent damage to the fuel system. Use the electronic service tool to perform "Fuel Pump Learn".
Caterpillar SIS machinery equipment:
Parts rebuild Caterpillar catalog:
1700557
REBUILD KIT
Caterpillar
Caterpillar
Caterpillar
Caterpillar
1430904
REBUILD KIT
Caterpillar
Caterpillar
1421700
REBUILD KIT
Caterpillar
Caterpillar
Caterpillar
Caterpillar
1M8040
REBUILD KIT
Caterpillar
Caterpillar
Caterpillar
Caterpillar
Caterpillar
Caterpillar