1862848 REBUILD KIT- Caterpillar parts
Rating:
Alternative (cross code) number:
CA1862848
186-2848
1862848
CA1862848
186-2848
1862848
Weight: 8 pounds 3 kg.
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 1862848 Water Pump Repair Kit for Model D353, D9H, 594H
CTP All impellers are balanced to improve pump performance and reduce vibration || All internal components are made to specifications to ensure CTP Components fit properly || Come with a stainless steel shaft to increase the longevity of the pump, while competitors use a carbon steel shaft
CTP All impellers are balanced to improve pump performance and reduce vibration || All internal components are made to specifications to ensure CTP Components fit properly || Come with a stainless steel shaft to increase the longevity of the pump, while competitors use a carbon steel shaft
CTP 1862848 Water Pump Repair Kit for Model D353, D9H, 594H
CTP All impellers are balanced to improve pump performance and reduce vibration || All internal components are made to specifications to ensure CTP Components fit properly || Come with a stainless steel shaft to increase the longevity of the pump, while competitors use a carbon steel shaft
CTP All impellers are balanced to improve pump performance and reduce vibration || All internal components are made to specifications to ensure CTP Components fit properly || Come with a stainless steel shaft to increase the longevity of the pump, while competitors use a carbon steel shaft
CTP 1862848 Water Pump Repair Kit for Model D353, D9H, 594H
CTP All impellers are balanced to improve pump performance and reduce vibration || All internal components are made to specifications to ensure CTP Components fit properly || Come with a stainless steel shaft to increase the longevity of the pump, while competitors use a carbon steel shaft
CTP All impellers are balanced to improve pump performance and reduce vibration || All internal components are made to specifications to ensure CTP Components fit properly || Come with a stainless steel shaft to increase the longevity of the pump, while competitors use a carbon steel shaft
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5481 Deep Well Socket 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03830988
Disconnect harness assembly (1) by unscrewing the connector.
Illustration 2 g03830996
Unscrew transformer (2) from the spark plug. Remove the copper washer (not shown).
Illustration 3 g03831004
Remove and inspect boot (3). Replace if necessary.
Illustration 4 g03831006
Use Tooling (A) to remove spark plug (2).
Repeat Steps 1 through 4 for the remaining spark plugs. Installation Procedure
Illustration 5 g03831006
Use Tooling (A) to install spark plug (4). The spark plug gap should be set at 0.64 0.03 mm (0.025 0.001 inch). Tighten the spark plugs to a torque of 35 5 N m (25 4 lb ft).
Illustration 6 g03831004
Illustration 7 g03830996
Install boot (3). Install the copper washer (not shown) onto the spark plug and install transformer (2). Tighten transformer (2) 1/8 inch past finger-tight, not exceeding 6.75 N m (60 lb in).
Illustration 8 g03830988
Connect harness assembly (1) and tighten the connector.
Repeat Steps 1 through 3 for the remaining spark plugs.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5481 Deep Well Socket 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03830988
Disconnect harness assembly (1) by unscrewing the connector.
Illustration 2 g03830996
Unscrew transformer (2) from the spark plug. Remove the copper washer (not shown).
Illustration 3 g03831004
Remove and inspect boot (3). Replace if necessary.
Illustration 4 g03831006
Use Tooling (A) to remove spark plug (2).
Repeat Steps 1 through 4 for the remaining spark plugs. Installation Procedure
Illustration 5 g03831006
Use Tooling (A) to install spark plug (4). The spark plug gap should be set at 0.64 0.03 mm (0.025 0.001 inch). Tighten the spark plugs to a torque of 35 5 N m (25 4 lb ft).
Illustration 6 g03831004
Illustration 7 g03830996
Install boot (3). Install the copper washer (not shown) onto the spark plug and install transformer (2). Tighten transformer (2) 1/8 inch past finger-tight, not exceeding 6.75 N m (60 lb in).
Illustration 8 g03830988
Connect harness assembly (1) and tighten the connector.
Repeat Steps 1 through 3 for the remaining spark plugs.
Parts rebuild Caterpillar catalog:
Caterpillar
Caterpillar
Caterpillar
Caterpillar
1700557
REBUILD KIT
Caterpillar
Caterpillar
Caterpillar
1M8046
REBUILD KIT
Caterpillar
Caterpillar
1M8045
REBUILD KIT
Caterpillar
Caterpillar
1M8044
REBUILD KIT
Caterpillar
Caterpillar
1M8043
REBUILD KIT
Caterpillar
Caterpillar
Caterpillar
1M8040
REBUILD KIT
Caterpillar
Caterpillar