2725837 RECEPTACLE AS Caterpillar parts
C4.4
Rating:
Alternative (cross code) number:
CA2725837
272-5837
2725837
CA2725837
272-5837
2725837
GENERATOR SET,
Compatible equipment models: 2725837:
Number on catalog scheme:
8
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 282-9962 Guide 1
346-4868 Guide 1
B 255-2820 Camshaft Pilot 2
C 8T-3169 Crank As 1
Illustration 1 g01228274
Typical Example
Illustration 2 g01228276
Typical Example
Note: The camshaft can be installed from either end of the engine.
Apply a thin coat of oil to Tooling (A) and Tooling (B). Install Tooling (B) into the ends of the camshaft. Install Tooling (C).Note: If, Tooling (A) was removed use the following Steps to install Tooling (A).
Install Tooling (B) into the engine until Tooling (B) is through the second camshaft bearing.
Slide Tooling (A) over Tooling (B).
Tighten the bolts for Tooling (A).
Remove Tooling (B).
Illustration 3 g01329080
Attach a suitable lifting device to the middle of camshaft (20). The weight of camshaft (20) is approximately 95 kg (210 lb). Install camshaft (20) halfway into the engine. Remove the suitable lifting device. Install camshaft (20). Use Tooling (C) to rotate camshaft (20). Rotate camshaft (20) to install camshaft (20).
Illustration 4 g01837094
Install cover (17). Install bolts (14).
Install elbow (18). Install bolts (19).
Connect tube assembly (16). Connect harness assembly (15).
Illustration 5 g01228236
Typical thrust washer with two or three bolts
Illustration 6 g06006064
Typical thrust washer with five bolts
Install the two or three bolt retainer (13). Install the washers and bolts (12). Tighten bolts (12) to a torque of 55 10 N m (41 7 lb ft).Install the five bolt retainer (13). Install the washers and bolts (12). Tighten bolts (12) to a torque of 73 12 N m (54 9 lb ft).
Illustration 7 g01228235
Refer to Testing and Adjusting, "Camshaft Timing" for the correct timing procedure. Install cam gear (11). Install spacer (10). Install and tighten bolts (8). Install and tighten bolt (9).
Illustration 8 g01837093
Install cover (7). Install bolts (6).
Install lifting bracket (1). Install bolts (2). Install cover (5). Install bolts (4). Connect harness assemblies (3).
Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".End By:
Install the valve lifter. Refer to Disassembly and Assembly, "Valve Lifter - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 282-9962 Guide 1
346-4868 Guide 1
B 255-2820 Camshaft Pilot 2
C 8T-3169 Crank As 1
Illustration 1 g01228274
Typical Example
Illustration 2 g01228276
Typical Example
Note: The camshaft can be installed from either end of the engine.
Apply a thin coat of oil to Tooling (A) and Tooling (B). Install Tooling (B) into the ends of the camshaft. Install Tooling (C).Note: If, Tooling (A) was removed use the following Steps to install Tooling (A).
Install Tooling (B) into the engine until Tooling (B) is through the second camshaft bearing.
Slide Tooling (A) over Tooling (B).
Tighten the bolts for Tooling (A).
Remove Tooling (B).
Illustration 3 g01329080
Attach a suitable lifting device to the middle of camshaft (20). The weight of camshaft (20) is approximately 95 kg (210 lb). Install camshaft (20) halfway into the engine. Remove the suitable lifting device. Install camshaft (20). Use Tooling (C) to rotate camshaft (20). Rotate camshaft (20) to install camshaft (20).
Illustration 4 g01837094
Install cover (17). Install bolts (14).
Install elbow (18). Install bolts (19).
Connect tube assembly (16). Connect harness assembly (15).
Illustration 5 g01228236
Typical thrust washer with two or three bolts
Illustration 6 g06006064
Typical thrust washer with five bolts
Install the two or three bolt retainer (13). Install the washers and bolts (12). Tighten bolts (12) to a torque of 55 10 N m (41 7 lb ft).Install the five bolt retainer (13). Install the washers and bolts (12). Tighten bolts (12) to a torque of 73 12 N m (54 9 lb ft).
Illustration 7 g01228235
Refer to Testing and Adjusting, "Camshaft Timing" for the correct timing procedure. Install cam gear (11). Install spacer (10). Install and tighten bolts (8). Install and tighten bolt (9).
Illustration 8 g01837093
Install cover (7). Install bolts (6).
Install lifting bracket (1). Install bolts (2). Install cover (5). Install bolts (4). Connect harness assemblies (3).
Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".End By:
Install the valve lifter. Refer to Disassembly and Assembly, "Valve Lifter - Install".
Caterpillar parts catalog:
Parts receptacle Caterpillar catalog:
2652105
RECEPTACLE AS-CONNECTOR
C4.4, D7R II
C4.4, D7R II
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 14M, 160M, 160M 2, 16M, 2864C, 311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM ...
1090, 1190, 1190T, 120K, 120K 2, 120M, 120M 2, 1290T, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 1390, 140G, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 2...
8N1528
RECEPTACLE AS
24H, 3612, 611, 657E, 657G, 785, 793C, 938G, 988H, 994, 994D, C280-12, IT38G
24H, 3612, 611, 657E, 657G, 785, 793C, 938G, 988H, 994, 994D, C280-12, IT38G
2839493
RECEPTACLE AS
3512, 3512B, 3512C, 3516, 3516B, 3516C, 793F, 793F CMD, 793F-XQ, 795F AC, 797F, 824K, 825K, 826K, 834K, 836K, 844K, 854K, 988K, 990K, 992K, 993K, 994H, C175-16, C175-20, C18, C280-12, C280-16, G3516H,...
3512, 3512B, 3512C, 3516, 3516B, 3516C, 793F, 793F CMD, 793F-XQ, 795F AC, 797F, 824K, 825K, 826K, 834K, 836K, 844K, 854K, 988K, 990K, 992K, 993K, 994H, C175-16, C175-20, C18, C280-12, C280-16, G3516H,...
2242735
RECEPTACLE AS-CONNECTOR
120M, 3516C, 621G, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 770G, 772G, 773G, 773G LRC, 773G OEM, 775G, 775G LRC, 775G OEM, 777G, 793F, 793F CMD, 793F-XQ, 795F AC, 797, 797B, 797F, 824K...
120M, 3516C, 621G, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 770G, 772G, 773G, 773G LRC, 773G OEM, 775G, 775G LRC, 775G OEM, 777G, 793F, 793F CMD, 793F-XQ, 795F AC, 797, 797B, 797F, 824K...
2853959
RECEPTACLE AS-CONNECTOR
C175-16
C175-16
2975488
RECEPTACLE AS-CONNECTOR
3512C, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 797F, 994H, C140-16, C175-16
3512C, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 797F, 994H, C140-16, C175-16
2736316
RECEPTACLE AS
2384C, 2484C, 3512C, 3516C, 525D, 535D, 545D, 555D, 559C, 579C, 725, 725C, 730, 730C, 735, 735B, 740, 740B, 785, 785B, 785C, 785D, 789, 789B, 789C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 79...
2384C, 2484C, 3512C, 3516C, 525D, 535D, 545D, 555D, 559C, 579C, 725, 725C, 730, 730C, 735, 735B, 740, 740B, 785, 785B, 785C, 785D, 789, 789B, 789C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 79...
3126E, 3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 365B, 844K, 990K, C175-16, C175-20, C27, C32, C7, C9, G3520B, G3606, G3606B, G3608, G3612, G3616, PM3516
1757061
RECEPTACLE AS-CONNECTOR
3512, 3512B, 3512C, 3516, 3516B, 3516C, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797F, C175-16, C18, C27, C32, C7.1, CX31-C13I, CX31-C15I, CX31-C18I, CX31-P600, G3516H, R1600H
3512, 3512B, 3512C, 3516, 3516B, 3516C, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797F, C175-16, C18, C27, C32, C7.1, CX31-C13I, CX31-C15I, CX31-C18I, CX31-P600, G3516H, R1600H
3512C, 3516C, 374F L, 390F L, 725C, 730C, 735B, 740B, 770G, 770G OEM, 772G, 772G OEM, 824K, 825K, 826K, 834K, 836K, 844K, 924K, 930K, 938K, 950K, 953D, 962K, 963D, 966K, 966M, 966M XE, 972K, 972M, 972...