AVSPARE.COM
parts catalog

RELAY 3237226 - Caterpillar



3237226 RELAY Caterpillar parts RELAY
Rating:
26
Alternative (cross code) number:
CA3237226
323-7226
3237226
Caterpillar 3237226 RELAY

Buy RELAY 3237226 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 22 g01760663
Install carrier assembly (21) into ring gear (35).
Install retaining ring (20).
Illustration 23 g01760645
Install spacer (19) and gear (18).
Illustration 24 g01760655Note: Make sure that the oil passages in shafts (17) are oriented toward the center of carrier assembly (16).
Raise the temperature of carrier assembly (16). Lower the temperature of (17) shafts. Install shafts (17) into carrier assembly (16) until the groove of shafts (17) is at Dimension (A). Dimension (A) equals 21.70 0.10 mm (0.854 0.004 inch).
Make eight stake marks at distance of Dimension (C) from each shaft (17). Dimension (C) equals 2.0 1.0 mm (0.08 0.04 inch). The width of each stake mark should be equal to Dimension (B). Dimension (B) equals 4.0 1.0 mm (0.16 0.04 inch).
Illustration 25 g01760651
Assemble carrier assembly (16), as follows.
Install carrier assembly in position on gear (18).
Illustration 26 g01760641
Install retaining ring (15) onto gear (18).
Illustration 27 g01760647
Install washer (12) and bearing assembly (14).
Install gear (13) and second washer (12).
Use Tooling (C) to install retaining ring (11).
Repeat Steps 26.a through 26.e for the other two planetary gears.
Illustration 28 g01760669
Install spacer (10) and gear (9).
Illustration 29 g01760650
Install O-ring seal (8) on plugs (5).
Illustration 30 g01760653
Install plugs (5) in cover (1). Install one 8.00 mm (0.315 inch) plate (7).
Position gear (6) and install bolts (4).
Illustration 31 g01751153
Illustration 32 g01751055
Place a piece of solder in the center of gear (9) (not shown).Note: You may need to apply some grease to the solder to keep the solder in position on gear (9).
Use Tooling (B) and a suitable lifting device to install cover (1). The weight of cover (1) is approximately 32 kg (70 lb).
Install four bolts (2) at 90 degrees from each other. Tighten bolts (2) in a crisscross pattern to a torque of 420 60 N m (310 44 lb ft). Turn bolts (2) and additional 60 5 degrees.
Remove bolts (2).
Use Tooling (B) and a suitable lifting device to remove cover (1). The weight of cover (1) is approximately 32 kg (70 lb).
Use a micrometer to measure the thickness of the solder. Record this measurement to determine the required thickness of plates (7). Adjust plates (7) to obtain a clearance of 1.000 + 1.000 mm (0.0394 + 0.0394 inch) between plate (7) and gear (9).
Apply Tooling (J) to the mating surfaces of cover (1) and the housing.
Use Tooling (B) and a suitable lifting device to install cover (1). The weight of cover (1) is approximately 32 kg (70 lb).
Install bolts (2). Tighten bolts (2) in a crisscross pattern to a torque of 420 60 N m (310 44 lb ft). Turn bolts (2) and additional 60 5 degrees.
Illustration 33 g06092181
Remove plug (5) (not shown). Attach Tooling (M) to the cover. Reduce the air pressure at the source to 103 kPa (15 psi). Apply air pressure to Tooling (M). This air will test the Duo-Cone seals.
Use the ball valve on Tooling (M) to eliminate the air pressure to the final drive. A pressure of 98 kPa (14.2 psi) must be maintained for 30 seconds.
Remove Tooling (M).


Parts relay Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.