0995401 REPAIR KIT Caterpillar parts
E110B
Rating:
Alternative (cross code) number:
CA0995401
099-5401
0995401
CA0995401
099-5401
0995401
Weight: 0.41 pounds 0 kg.
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
TM USWWAGOODS Replacement For/Fits 099-5401 0995401 Boom Cylinder Seal Kit Fits erpillar Fits E110B
USWWAGOODS TM USWWAGOODS Replacement For/Fits 099-5401 0995401 Boom Cylinder Seal Kit Fits erpillar Fits E110B || Replacement For/Fits Mower Parts for Bad Boy, for Briggs & Stratton, for Cub Cadet, for Honda, for Sears, for Snapper & More! Agriculture Parts for John Deere, for Ford/New Holland, for Case, for Massey Ferguson & More! || Trusted brand with a history of excellence || Improved fuel efficiency and reduced emissions || Compatibility with a wide range of tractor models
USWWAGOODS TM USWWAGOODS Replacement For/Fits 099-5401 0995401 Boom Cylinder Seal Kit Fits erpillar Fits E110B || Replacement For/Fits Mower Parts for Bad Boy, for Briggs & Stratton, for Cub Cadet, for Honda, for Sears, for Snapper & More! Agriculture Parts for John Deere, for Ford/New Holland, for Case, for Massey Ferguson & More! || Trusted brand with a history of excellence || Improved fuel efficiency and reduced emissions || Compatibility with a wide range of tractor models
TM USWWAGOODS Replacement For/Fits 0995401 Boom Cylinder Seal Kit Fits Fits erpillar E110B
USWWAGOODS TM USWWAGOODS Replacement For/Fits 0995401 Boom Cylinder Seal Kit Fits Fits erpillar E110B || Replacement For/Fits Model: E110B. Appliion: Boom. Mower Parts for Bad Boy, for Briggs & Stratton, for Cub Cadet, for Honda, for Sears, for Snapper & More! Cylinder: 995402, 995403. Agriculture Parts for John Deere, for Ford/New Holland, for Case, for Massey Ferguson & More! || Trusted brand with a history of excellence || Improved fuel efficiency and reduced emissions || Compatibility with a wide range of tractor models
USWWAGOODS TM USWWAGOODS Replacement For/Fits 0995401 Boom Cylinder Seal Kit Fits Fits erpillar E110B || Replacement For/Fits Model: E110B. Appliion: Boom. Mower Parts for Bad Boy, for Briggs & Stratton, for Cub Cadet, for Honda, for Sears, for Snapper & More! Cylinder: 995402, 995403. Agriculture Parts for John Deere, for Ford/New Holland, for Case, for Massey Ferguson & More! || Trusted brand with a history of excellence || Improved fuel efficiency and reduced emissions || Compatibility with a wide range of tractor models
Replacement Parts for Snow Removal UTV ATV Cart Machinery for 0995401 Boom Cylinder Seal Kit for CAT for Caterpillar E110B Model-DFC589-Gl31073
Generic Quality-engineered parts specifically for lawn care, snow removal, UTV, ATV, and golf cart equipment || Made from rugged, weatherproof materials for longevity across all outdoor applications || Designed for a precise fit, making repairs and replacements simple and effective || Keeps machinery running smoothly, reducing wear and tear for long-term use || Universal compatibility with many brands and models, providing broad coverage for different equipment
Generic Quality-engineered parts specifically for lawn care, snow removal, UTV, ATV, and golf cart equipment || Made from rugged, weatherproof materials for longevity across all outdoor applications || Designed for a precise fit, making repairs and replacements simple and effective || Keeps machinery running smoothly, reducing wear and tear for long-term use || Universal compatibility with many brands and models, providing broad coverage for different equipment
Number on catalog scheme:
31-41
For full view, you need register
Compatible equipment models: 0995401:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 279-3473 Engine Turning Tool 1
329-3831(1) Air Power Turning Tool 1
B 274-5875(2) Guide 2
418-1340(3) Guide 2
339-6503 Bolt 2
C 8T-2686 Puller Group 1
D 328-5926 Spacer 1
E 322-3564 Cylinder Puller 1
F 288-9169 Installation Bracket 1
2P-8260 Liner Installer 1
G - Loctite Moly Paste 1LB 1
H - Loctite LB8801 Silicone Lubricant -
(1) Optional
(2) Use for engine serial numbers 1-999 (type 1)
(3) Use for engine serial numbers 1000-99999 (type 2)Start By:
Remove the cylinder head.
Remove the piston cooling jet.
Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct draining and filling procedure.
Illustration 1 g01831951Note: Inspect the connecting rod and connecting rod cap for the proper identification mark. The connecting rod and the connecting rod cap should have an etched number on the side. The number should match the cylinder number. Mark the connecting rod and the connecting rod cap, if necessary. Careful handling is required for fractured connecting rods. The connecting rod and the rod cap should be placed on the sides in order to prevent damage. When possible, the connecting rod and the rod cap should be bolted together in order to prevent damage.
Use Tooling (A) to rotate the flywheel in order to access the connecting rod cap that will be removed.
Remove bolts (1) and connecting rod cap (2). Position the crankshaft so that the piston is at the bottom dead center. Inspect the connecting rod bearing for wear or for damage.
Illustration 2 g01240845
Install Tooling (B) onto the connecting rod.
Illustration 3 g01240763
Install Tooling (C). Hold the bolt of Tooling (C) and turn the nut. Turn the nut until the nut is tight.
Rotate the engine in order to position the cylinder pack to the proper height and install Tooling (D).
Illustration 4 g01997933
Install Tooling (D). Remove Tooling (C). Note: Do not remove the cylinder pack with Tooling (C).
Illustration 5 g01765495
Install Tooling (E) onto the piston liner. Rotate the engine in order to position the piston to the top. Attach Tooling (E) to the piston. Attach a suitable lifting device onto Tooling (E). The weight of the piston, the liner, and the connecting rod is approximately 50 kg (110 lb). Remove Tooling (D).
Illustration 6 g01765496
Remove cylinder pack (3) from the cylinder block. Installation Procedure
Note: Ensure that the top O-ring seal for the liner is at least 20 °C (68 °F) before installation of liners into the cylinder block. Assembly with a cold seal may result in damage to the O-ring seal or to the installation tool.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 279-3473 Engine Turning Tool 1
329-3831(1) Air Power Turning Tool 1
B 274-5875(2) Guide 2
418-1340(3) Guide 2
339-6503 Bolt 2
C 8T-2686 Puller Group 1
D 328-5926 Spacer 1
E 322-3564 Cylinder Puller 1
F 288-9169 Installation Bracket 1
2P-8260 Liner Installer 1
G - Loctite Moly Paste 1LB 1
H - Loctite LB8801 Silicone Lubricant -
(1) Optional
(2) Use for engine serial numbers 1-999 (type 1)
(3) Use for engine serial numbers 1000-99999 (type 2)Start By:
Remove the cylinder head.
Remove the piston cooling jet.
Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct draining and filling procedure.
Illustration 1 g01831951Note: Inspect the connecting rod and connecting rod cap for the proper identification mark. The connecting rod and the connecting rod cap should have an etched number on the side. The number should match the cylinder number. Mark the connecting rod and the connecting rod cap, if necessary. Careful handling is required for fractured connecting rods. The connecting rod and the rod cap should be placed on the sides in order to prevent damage. When possible, the connecting rod and the rod cap should be bolted together in order to prevent damage.
Use Tooling (A) to rotate the flywheel in order to access the connecting rod cap that will be removed.
Remove bolts (1) and connecting rod cap (2). Position the crankshaft so that the piston is at the bottom dead center. Inspect the connecting rod bearing for wear or for damage.
Illustration 2 g01240845
Install Tooling (B) onto the connecting rod.
Illustration 3 g01240763
Install Tooling (C). Hold the bolt of Tooling (C) and turn the nut. Turn the nut until the nut is tight.
Rotate the engine in order to position the cylinder pack to the proper height and install Tooling (D).
Illustration 4 g01997933
Install Tooling (D). Remove Tooling (C). Note: Do not remove the cylinder pack with Tooling (C).
Illustration 5 g01765495
Install Tooling (E) onto the piston liner. Rotate the engine in order to position the piston to the top. Attach Tooling (E) to the piston. Attach a suitable lifting device onto Tooling (E). The weight of the piston, the liner, and the connecting rod is approximately 50 kg (110 lb). Remove Tooling (D).
Illustration 6 g01765496
Remove cylinder pack (3) from the cylinder block. Installation Procedure
Note: Ensure that the top O-ring seal for the liner is at least 20 °C (68 °F) before installation of liners into the cylinder block. Assembly with a cold seal may result in damage to the O-ring seal or to the installation tool.
Caterpillar parts catalog:
Parts repair Caterpillar catalog:
5I6358
REPAIR KIT
D7G, E110B, E120B
D7G, E110B, E120B
E110B, E120B, E200B, E240C, E300B, E70B, EL240B
E110B, E120B, E200B, E240C, EL240B
E110B, E120B
0990315
REPAIR KIT
E110B, E120B
E110B, E120B
0990341
REPAIR KIT
E110B, E120B
E110B, E120B
0997860
REPAIR KIT
E110B, E120B
E110B, E120B
E110B, E120B, E70B
E110B, E120B
E110B, E120B
E110B, E120B
1R7903
REPAIR KIT
E110B, E120B
E110B, E120B
E110B, E120B
E110B, E120B
E120B
E110B, E120B, E70B
0997860
REPAIR KIT
E110B, E120B
E110B, E120B
0990341
REPAIR KIT
E110B, E120B
E110B, E120B
0934314
REPAIR KIT
E70, E70B
E70, E70B