1377581 RETAINER Caterpillar parts
30/30, 35, 45, 55, 65E, 75E, 85E, 950G, 950G II, 950H, 950K, 95E, 962G, 962G II, 962H, 962K, 966G, 966G II, 966H, 972G, 972G II, 972H, 980G, 980G II, 980H, DEUCE
Rating:
Alternative (cross code) number:
CA1377581
137-7581
1377581
CA1377581
137-7581
1377581
Weight: 0.03 pounds 0 kg.
CHALLENGER, WHEEL LOADER,
Compatible equipment models: 1377581:
Number on catalog scheme:
19
For full view, you need register
Information:
Table 3
FMI 4 Troubleshooting
Troubleshooting Test Steps Values Results
1. Check The Sensor
A. Turn the disconnect switch and the key start switch ON.
B. Disconnect the sensor from the machine harness.
C. Observe the status of the diagnostic code as the sensor is disconnected from the harness.
The code changes from an FMI 4 to an FMI 3 when the sensor is disconnected. OK - The code changes from an FMI 4 to an FMI 3 when the sensor is disconnected. The sensor has failed.
Repair: Replace the sensor.
Proceed to Test Step 3.
NOT OK - The FMI 4 diagnostic code remains active when sensor is disconnected. The sensor is not the cause of the problem.
Proceed to Test Step 2.
2. Check The Signal Circuit For A Short To Ground
A. Turn the key start switch and the disconnect switch OFF.
B. Disconnect the harness connectors from the ECM. The sensor remains disconnected from the machine harness.
C. At the ECM harness connector, measure the resistance between the sensor signal contact and all possible sources of ground.
All resistance values are greater than 5K Ω. OK - All resistance values are greater than 5K Ω. The harness circuit is correct.
Proceed to Test Step 3.
NOT OK - One or more readings are less than 5 Ω. A short circuit exists between the signal circuit .
Repair: Repair or replace the machine harness.
Note: A resistance that is greater than 5 Ω but less than 5K Ω would indicate a loose connection or a corroded connection in the circuit. A resistance measurement that is greater than 5K Ω would indicate an open in the circuit.
Proceed to Test Step 3.
3. Check If The Diagnostic Code Remains
A. Reconnect all harness connectors. Return machine to normal operating condition.
B. Turn the key start switch and the disconnect switch ON.
C. Clear all diagnostic codes.
D. Operate the machine.
E. Stop the machine and engage the safety lock .
F. Check if the diagnostic code is active.
The diagnostic code is no longer present. OK - The diagnostic code does not exist currently. The initial diagnostic code may have been caused by poor electrical connection or short at one of the harness connections. Resume machine operation.
STOP.
NOT OK - The diagnostic trouble code has not been corrected. If the diagnostic code has not been corrected after performing the procedure a second time, the ECM may require replacement.
Prior to replacing the ECM, always contact the Technical Communicator at your dealership for possible consultation with Caterpillar. This consultation may effect repair time.
Follow the steps in Troubleshooting, "ECM - Replace" if the ECM needs to be replaced.
STOP.
Table 4
FMI 8 Troubleshooting
Troubleshooting Test Steps Values Results
1. Check The Signal Of The Sensor
A. Turn the key start switch and disconnect switch to the OFF position.
B. At the back of the harness connector for the sensor, insert multimeter probes along the signal contact and return contact.
Note: Use Cat® Electronic Technician (Cat ET) Service Tool if access to the sensor while operating the machine, is not safe.
C. Turn the disconnect switch and the key start switch to the ON position.
D. Monitor the signal
Cat SIS web machinery list:
Parts retainer Caterpillar catalog:
1341830
RETAINER-SPRING
30/30, 65E, 75E, 85E, 95E, AP-1055B, AP-655C, AP-655D, BG-2455C, BG-2455D, BG655D, DEUCE
30/30, 65E, 75E, 85E, 95E, AP-1055B, AP-655C, AP-655D, BG-2455C, BG-2455D, BG655D, DEUCE
1561267
RETAINER
35, 416D, 420D, 424D, 430D, 432D, 442D, 446D, 45, 525C, 535C, 545C, 55, D5N, D6N
35, 416D, 420D, 424D, 430D, 432D, 442D, 446D, 45, 525C, 535C, 545C, 55, D5N, D6N
1143906
RETAINER
35, 416D, 420D, 424D, 430D, 432D, 442D, 446D, 45, 515, 517, 525, 525B, 525C, 527, 535B, 535C, 545, 545C, 55, D5N, D6N, R1300, R1600, R1600G
35, 416D, 420D, 424D, 430D, 432D, 442D, 446D, 45, 515, 517, 525, 525B, 525C, 527, 535B, 535C, 545, 545C, 55, D5N, D6N, R1300, R1600, R1600G
1445427
RETAINER
45, 55
45, 55
1354729
RETAINER AS
65C, 65E, 75D, 75E, 85D, 85E, 95E
65C, 65E, 75D, 75E, 85D, 85E, 95E
6E4101
RETAINER-SEAL
65C, 75D, 85D, D8N, D8R
65C, 75D, 85D, D8N, D8R
10 FT, 10-20B, 10B, 550, 570, 580, 65E, 75E, 8 FT, 8-16B, 85E, 928F, 938F, 95E, AP-1000, AP-1000B, AP-1050, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP-800, AP-800C, AP-800D, AP-900B, A...
5R5778
RETAINER
10 FT, 65E, 75E, 85E, 95E, AP-1000, AP-1050, AP-800, PF-300C, PS-300B
10 FT, 65E, 75E, 85E, 95E, AP-1000, AP-1050, AP-800, PF-300C, PS-300B
10 FT, 10-20B, 1090, 10B, 1190, 1190T, 1290T, 35, 45, 65E, 75E, 8 FT, 8-16B, 85E, 95E, AP-1000, AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP-800, AP-800C, AP-800D, AP-900B, AP1...
2100339
RETAINER
35, 45
35, 45
2100338
RETAINER
35, 45
35, 45
1475630
RETAINER
65E, 75E, 85E, 953D, 95E, 963D, 973D
65E, 75E, 85E, 953D, 95E, 963D, 973D