1868990 RETAINER AS Caterpillar parts
R1300, R1300G, R1300G II
Rating:
Alternative (cross code) number:
CA1868990
186-8990
1868990
CA1868990
186-8990
1868990
Weight: 15 pounds 6 kg.
LOAD HAUL DUMP,
Information:
Machine ECM
The following code is associated with the engine speed dial related to the Machine ECM.
Table 1
Machine ECM (MID 039)
DTC Code Description System Response
586-12 Engine Speed Dial Switch : Bad device or component Cannot control engine speed. Possible causes for an FMI 12 Diagnostic code are:
The dial switch has failed.
The engine governor control has failed.
The CAN Data Link between the Switch Panel and the Machine ECM is working intermittently or has failed.
The machine harness to the dial switch or the governor control has failed.
The ECM has failed. This situation is unlikely.
Illustration 1 g06126793
Engine Speed (governor control) schematic
Note: The diagram above is a simplified schematic of the Machine ECM connections. The schematic is electrically correct. However, not all the possible harness connectors are shown. Refer to the latest revision of Electrical Schematic, UENR5968.Diagnostic Trouble Code Procedure
Note: Prior to beginning this procedure, inspect the harness connectors that are involved in this circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. If a problem with a connection is found, correct the problem and verify that the diagnostic code is active before performing a troubleshooting procedure.
Table 2
Troubleshooting Test Steps Values Results
1. Check For An Active Diagnostic Code
A. Turn the key start switch to the ON position.
B. Use Cat ET to check for all active diagnostic codes.
B. Check for DTC 586-12.
C. Check for DTC 246-9 or DTC 246-19.
Diagnostic code CID 586 FMI 12 is active. OK - DTC 586-12 is active without either DTC 246-9 or DTC 246-19 being active.
Proceed to Test Step 2.
NOT OK - Diagnostic code DTC 586-12 AND DTC 246-9 or DTC 246-19 are active.
Repair: Follow the procedure for troubleshooting the code for the data link circuit.
Result: If DTC code 586-12 is no longer active, return the machine to service.
If, after troubleshooting the data link, DTC 586-12 is active, proceed to Test Step 2.
2. Inspect The Switch Panel Harness Connection
A. Turn the disconnect switch to the OFF position.
B. Inspect the harness connector making sure that the connector is clean and tight.
C. Check the connector for proper mating.
D. Check the connector. Ensure that the wires are secured tightly into the connector. Take care not to pull the wire out of the connector.
E. Check any exposed wires at the connector for nicks or signs of abrasion.
F. Check for moisture inside the connector.
G. Check the connector for dirty contacts or corroded contacts.
H. Check each pin and each socket of the switch panel harness connectors. Ensure that the contacts are properly installed. The contacts should mate correctly when the two pieces of the connector are placed together.
The machine harness connectors are tight and free of corrosion. OK - The machine harness connectors are tight and free of corrosion.
Proceed to Test Step 3.
NOT OK - The machine harness connectors are in need of repair.
Repair: Repair or replace the machine harness.
Proceed to Test Step 5.
3. Check The Governor Signal Circuit
Reference the Illustration in this section of the
The following code is associated with the engine speed dial related to the Machine ECM.
Table 1
Machine ECM (MID 039)
DTC Code Description System Response
586-12 Engine Speed Dial Switch : Bad device or component Cannot control engine speed. Possible causes for an FMI 12 Diagnostic code are:
The dial switch has failed.
The engine governor control has failed.
The CAN Data Link between the Switch Panel and the Machine ECM is working intermittently or has failed.
The machine harness to the dial switch or the governor control has failed.
The ECM has failed. This situation is unlikely.
Illustration 1 g06126793
Engine Speed (governor control) schematic
Note: The diagram above is a simplified schematic of the Machine ECM connections. The schematic is electrically correct. However, not all the possible harness connectors are shown. Refer to the latest revision of Electrical Schematic, UENR5968.Diagnostic Trouble Code Procedure
Note: Prior to beginning this procedure, inspect the harness connectors that are involved in this circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. If a problem with a connection is found, correct the problem and verify that the diagnostic code is active before performing a troubleshooting procedure.
Table 2
Troubleshooting Test Steps Values Results
1. Check For An Active Diagnostic Code
A. Turn the key start switch to the ON position.
B. Use Cat ET to check for all active diagnostic codes.
B. Check for DTC 586-12.
C. Check for DTC 246-9 or DTC 246-19.
Diagnostic code CID 586 FMI 12 is active. OK - DTC 586-12 is active without either DTC 246-9 or DTC 246-19 being active.
Proceed to Test Step 2.
NOT OK - Diagnostic code DTC 586-12 AND DTC 246-9 or DTC 246-19 are active.
Repair: Follow the procedure for troubleshooting the code for the data link circuit.
Result: If DTC code 586-12 is no longer active, return the machine to service.
If, after troubleshooting the data link, DTC 586-12 is active, proceed to Test Step 2.
2. Inspect The Switch Panel Harness Connection
A. Turn the disconnect switch to the OFF position.
B. Inspect the harness connector making sure that the connector is clean and tight.
C. Check the connector for proper mating.
D. Check the connector. Ensure that the wires are secured tightly into the connector. Take care not to pull the wire out of the connector.
E. Check any exposed wires at the connector for nicks or signs of abrasion.
F. Check for moisture inside the connector.
G. Check the connector for dirty contacts or corroded contacts.
H. Check each pin and each socket of the switch panel harness connectors. Ensure that the contacts are properly installed. The contacts should mate correctly when the two pieces of the connector are placed together.
The machine harness connectors are tight and free of corrosion. OK - The machine harness connectors are tight and free of corrosion.
Proceed to Test Step 3.
NOT OK - The machine harness connectors are in need of repair.
Repair: Repair or replace the machine harness.
Proceed to Test Step 5.
3. Check The Governor Signal Circuit
Reference the Illustration in this section of the
Caterpillar parts catalog:
Parts retainer Caterpillar catalog:
4W0924
RETAINER
12H, 12H ES, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 235B, 245, 330, 330 FM L, 330 L, 3304, 3304B, 3306, 3306B, 3306C, 330B, 330B L, 3406, 3406B,...
12H, 12H ES, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 235B, 245, 330, 330 FM L, 330 L, 3304, 3304B, 3306, 3306B, 3306C, 330B, 330B L, 3406, 3406B,...
7N9035
RETAINER
12H, 12H ES, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 235B, 245, 330, 330 FM L, 330 L, 3304, 3304B, 3306, 3306B, 3306C, 330B, 330B L, 3406, 3406B,...
12H, 12H ES, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 235B, 245, 330, 330 FM L, 330 L, 3304, 3304B, 3306, 3306B, 3306C, 330B, 330B L, 3406, 3406B,...
9S2390
RETAINER
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 235, 2...
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 235, 2...
4M1828
RETAINER-SPRING
1090, 1140, 1150, 1160, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120M, 1290T, 12E, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14G, 14H, 14H NA, 14M...
1090, 1140, 1150, 1160, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120M, 1290T, 12E, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14G, 14H, 14H NA, 14M...
4M1827
RETAINER-SPRING
1090, 1140, 1150, 1160, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120M, 1290T, 12E, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14G, 14H, 14H NA, 14M...
1090, 1140, 1150, 1160, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120M, 1290T, 12E, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14G, 14H, 14H NA, 14M...
8M1013
RETAINER
14E, 24H, 24M, 30/30, 517, 518, 518C, 527, 561M, 572G, 572R II, 578, 583R, 587R, 587T, 589, 594, 611, 613, 613B, 613C, 613C II, 613G, 615, 615C, 65, 651E, 657B, 657E, 65C, 65E, 7211, 75, 75C, 75D, 75E...
14E, 24H, 24M, 30/30, 517, 518, 518C, 527, 561M, 572G, 572R II, 578, 583R, 587R, 587T, 589, 594, 611, 613, 613B, 613C, 613C II, 613G, 615, 615C, 65, 651E, 657B, 657E, 65C, 65E, 7211, 75, 75C, 75D, 75E...
2768123
RETAINER
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 323D2 L, 420E, 430E, 450E, 525D, 535D, 545D, 553C, 559, 613G, 914G, 924H, 924HZ, 924K, 928H, 928HZ, 930K, 938H, 938K, 950 GC, 953D, 963D, AP-600D, AP-655D, A...
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 323D2 L, 420E, 430E, 450E, 525D, 535D, 545D, 553C, 559, 613G, 914G, 924H, 924HZ, 924K, 928H, 928HZ, 930K, 938H, 938K, 950 GC, 953D, 963D, AP-600D, AP-655D, A...
4S5824
RETAINER
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 515, 518, 518C, 525, 525B, 525C, 527, 535B, 535C, 545, 545C, 611, 613, 613B, 613C, 613C II, 613G, 615, 615C, 814, 814B, 814F, 815, 815B...
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 515, 518, 518C, 525, 525B, 525C, 527, 535B, 535C, 545, 545C, 611, 613, 613B, 613C, 613C II, 613G, 615, 615C, 814, 814B, 814F, 815, 815B...
1S5596
RETAINER
508, 517, 621, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966D, 966F, 966F II, 966G, 966G II, 966H, 966K, 966M, 970F, 972G, 972G II, 972H, 972K, 972M, D4H, D4HTSK II, D4HTSK III, D5H, R1...
508, 517, 621, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966D, 966F, 966F II, 966G, 966G II, 966H, 966K, 966M, 970F, 972G, 972G II, 972H, 972K, 972M, D4H, D4HTSK II, D4HTSK III, D5H, R1...
3G2241
RETAINER-SEAL
615, 615C, 621B, 621E, 621F, 621G, 623E, 623F, 623G, 627B, 627E, 627F, 627G, 631C, 633D, 639D, 641B, 651E, 657E, 657G, 772, 824C, 826C, 966C, 966D, 966F, 966F II, 970F, 973, 977K, 977L, 980B, 980G, 99...
615, 615C, 621B, 621E, 621F, 621G, 623E, 623F, 623G, 627B, 627E, 627F, 627G, 631C, 633D, 639D, 641B, 651E, 657E, 657G, 772, 824C, 826C, 966C, 966D, 966F, 966F II, 970F, 973, 977K, 977L, 980B, 980G, 99...
3G1264
RETAINER
163, 183B, 572G, 594H, 611, 613C, 613C II, 613G, 615C, 621B, 621E, 621F, 621G, 623B, 623E, 623F, 623G, 627B, 627E, 627F, 627G, 633C, 633D, 641B, 651E, 657E, 657G, 772, 814, 814B, 814F, 814F II, 815B, ...
163, 183B, 572G, 594H, 611, 613C, 613C II, 613G, 615C, 621B, 621E, 621F, 621G, 623B, 623E, 623F, 623G, 627B, 627E, 627F, 627G, 633C, 633D, 641B, 651E, 657E, 657G, 772, 814, 814B, 814F, 814F II, 815B, ...
4E8534
RETAINER-SEAL
528, 528B, 530B, 814B, 815B, 816B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966D, 966F, 966G, D250E II, D25D, D300E, D300E II, D350E, D350E II, D400E, D40D...
528, 528B, 530B, 814B, 815B, 816B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966D, 966F, 966G, D250E II, D25D, D300E, D300E II, D350E, D350E II, D400E, D40D...
1869898
RETAINER
R1300, R1300G, R1300G II
R1300, R1300G, R1300G II
1869899
RETAINER
R1300, R1300G
R1300, R1300G
1634800
RETAINER AS
797, 797B
797, 797B
1647134
RETAINER
797
797
2995372
RETAINER
797, 797B, 797F
797, 797B, 797F
1940589
RETAINER
797, 797B
797, 797B
2031746
RETAINER
AD30, AD45, AD45B, AD55, AD55B, AD60, AE40 II, R1300G, R1300G II, R1600, R1600G, R1600H, R1700G, R2900, R2900G, R3000H
AD30, AD45, AD45B, AD55, AD55B, AD60, AE40 II, R1300G, R1300G II, R1600, R1600G, R1600H, R1700G, R2900, R2900G, R3000H
2482993
RETAINER AS
R1300G
R1300G
2433426
RETAINER
R1300G, R1300G II
R1300G, R1300G II
1869845
RETAINER AS
R1300, R1300G, R1300G II
R1300, R1300G, R1300G II
2228083
RETAINER
AD30, AD45, AD45B, AD55, AD55B, AD60, AE40 II, R1300, R1300G, R1300G II, R1600, R1600G, R1600H, R1700 II, R1700G, R2900, R2900G, R3000H
AD30, AD45, AD45B, AD55, AD55B, AD60, AE40 II, R1300, R1300G, R1300G II, R1600, R1600G, R1600H, R1700 II, R1700G, R2900, R2900G, R3000H
3017161
RETAINER
R1300G, R1300G II
R1300G, R1300G II