2322179 RETAINER Caterpillar parts
385B
Rating:
Alternative (cross code) number:
CA2322179
232-2179
2322179
CA2322179
232-2179
2322179
Weight: 1 pounds 0 kg.
EXCAVATOR,
Compatible equipment models: 2322179:
Number on catalog scheme:
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M10 by 100 mm 2 Start By:
Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01470403
Typical example
Remove the bolts from Position (X) from flywheel housing (1).
Install Tooling (A) into Position (X) on flywheel housing (1).
Install a suitable lifting device to the flywheel housing in order to support the flywheel housing. The flywheel housing weighs approximately 30 kg (66 lb).
Illustration 2 g01763013
Typical example
Remove bolts (2) and remaining bolts (3) from flywheel housing (1).
Use the lifting device in order to remove flywheel housing (1) from the cylinder block.
Illustration 3 g01470418
Typical example
If the engine has an aluminum oil pan, remove dust seal (5).
If necessary, remove dowels (4) from the cylinder block. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A - Guide Bolt
M10 by 100 mm 2
B 8T-5096 Dial Indicator Group 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the flywheel housing is clean and free from damage. If necessary, replace the flywheel housing.
Illustration 4 g01244056
Typical example
Inspect crankshaft rear seal (6) for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" and refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Clean the rear face of the cylinder block. If necessary, install dowels (4) to the cylinder block.
Install Tooling (A) to the cylinder block.
Install dust seal (5).
Illustration 5 g01763034
Typical example
Install a suitable lifting device to the flywheel housing. The flywheel housing weighs approximately 30 kg (66 lb).
Use the lifting device to align flywheel housing (1) with Tooling (A). Install the flywheel housing to the cylinder block.
Install bolts (2) and bolts (3) finger tight.
Remove Tooling (A). Install remaining bolts (3).
Tighten bolts (3) to a torque of 63 N m (46 lb ft).
Tighten bolts (2) to a torque of 75 N m (55 lb ft).
Use Tooling (B) to check the alignment of the flywheel housing with the crankshaft. Refer to Systems Operation, Testing and Adjusting, "Flywheel Housing - Inspect". End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M10 by 100 mm 2 Start By:
Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01470403
Typical example
Remove the bolts from Position (X) from flywheel housing (1).
Install Tooling (A) into Position (X) on flywheel housing (1).
Install a suitable lifting device to the flywheel housing in order to support the flywheel housing. The flywheel housing weighs approximately 30 kg (66 lb).
Illustration 2 g01763013
Typical example
Remove bolts (2) and remaining bolts (3) from flywheel housing (1).
Use the lifting device in order to remove flywheel housing (1) from the cylinder block.
Illustration 3 g01470418
Typical example
If the engine has an aluminum oil pan, remove dust seal (5).
If necessary, remove dowels (4) from the cylinder block. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A - Guide Bolt
M10 by 100 mm 2
B 8T-5096 Dial Indicator Group 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the flywheel housing is clean and free from damage. If necessary, replace the flywheel housing.
Illustration 4 g01244056
Typical example
Inspect crankshaft rear seal (6) for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" and refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Clean the rear face of the cylinder block. If necessary, install dowels (4) to the cylinder block.
Install Tooling (A) to the cylinder block.
Install dust seal (5).
Illustration 5 g01763034
Typical example
Install a suitable lifting device to the flywheel housing. The flywheel housing weighs approximately 30 kg (66 lb).
Use the lifting device to align flywheel housing (1) with Tooling (A). Install the flywheel housing to the cylinder block.
Install bolts (2) and bolts (3) finger tight.
Remove Tooling (A). Install remaining bolts (3).
Tighten bolts (3) to a torque of 63 N m (46 lb ft).
Tighten bolts (2) to a torque of 75 N m (55 lb ft).
Use Tooling (B) to check the alignment of the flywheel housing with the crankshaft. Refer to Systems Operation, Testing and Adjusting, "Flywheel Housing - Inspect". End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Caterpillar SIS machinery equipment:
Parts retainer Caterpillar catalog:
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 235, 2...
1090, 1140, 1150, 1160, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120M, 1290T, 12E, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14G, 14H, 14H NA, 14M...
1090, 1140, 1150, 1160, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120M, 1290T, 12E, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14G, 14H, 14H NA, 14M...
3406B, 3406C, 3406E, 3456, 375, 375 L, 385B, 5080, 5090B, 578, 583R, 621G, 623G, 627F, 627G, 651B, 657B, 735, 740, 824C, 824G, 824G II, 825G, 825G II, 826C, 826G, 826G II, 834G, 836G, 980C, 980G, 980G...
16G, 16H NA, 24H, 24M, 3126, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3456, 3516, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C...
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 235B, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS...
318C, 320B, 320C, 320D, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320E, 320E L, 321C, 321D LCR, 322B L, 322C, 323D L, 323D2 L, 324D, 324D L, 324E L, 324E LN, 325B L, 325C, 325D, 325D L, 326D L, 329D,...
345C L, 365B, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 390D, 5080, 5090B, 5110B, 992C, 992G, 994, 994D, 994F
329D L, 345C, 345C L, 345D L, 365B, 365B II, 365C, 365C L, 365C L MH, 375, 385B, 385C, 385C FS, 385C L, 5080, 5090B, 5130, 980H, 980K, 994, 994D, 994F, 994H, D11R, D11T
345B II, 345C L, 350, 365B, 365B II, 365C, 365C L, 374D L, 375, 375 L, 385B, 385C, 385C L, 390D, 5080, 5110B, 5230, 988H, 988K, 990, 990 II, 990H, 992G
1588976
RETAINER
365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
1447092
RETAINER-SPRING
365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B
365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B
1239211
RETAINER-ROCKER ARM
G3606, G3608, G3612, G3616
G3606, G3608, G3612, G3616
8P4900
RETAINER-BEARING
D10, D11N, D6D
D10, D11N, D6D
1943313
RETAINER GP-DOOR
D5N, D5R LGP, D6N, D6N LGP
D5N, D5R LGP, D6N, D6N LGP
1943309
RETAINER GP-DOOR
D5N, D5R LGP, D6N, D6N LGP
D5N, D5R LGP, D6N, D6N LGP
7C6618
RETAINER GP-PUSHROD
3606, 3608, 3612, 3616
3606, 3608, 3612, 3616
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793C, 793D, 797, 797B, 854G, 992G...
2208812
RETAINER AS
5110B, 5130B
5110B, 5130B
1380007
RETAINER-G.E.T.
5130, 5230, 988G, 990, 990 II, 990H, 994, 994D
5130, 5230, 988G, 990, 990 II, 990H, 994, 994D
4T5739
RETAINER GP-MOTOR
227, 235, 245, 943, 953, 963
227, 235, 245, 943, 953, 963
1905001
RETAINER GP
DEUCE
DEUCE
1543788
RETAINER GP-FORK
TH103, TH62, TH63, TH82, TH83
TH103, TH62, TH63, TH82, TH83
311C, 311D LRR, 312, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 314D CR, 314D LCR, 315, 315C, 316E L, 317, 317B LN, 318B, 318C, 320B, 320C, 322B L, 322C, 325B L, 325C, 330, 33...