AVSPARE.COM
parts catalog

RETAINER 2H9672 - Caterpillar



2H9672 RETAINER Caterpillar parts 627B RETAINER
Rating:
15
Alternative (cross code) number:
CA2H9672
2H-9672
2H9672
Caterpillar 2H9672 RETAINER

Buy RETAINER 2H9672 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL SCRAPER,

Compatible equipment models: 2H9672:

WHEEL SCRAPER  627B   Caterpillar
Number on catalog scheme: 1
 
  For full view, you need register

Information:

You must read and understand the warnings and instructions contained in the Safety section of this manual before performing any operation or maintenance procedures. Transmission Oil Filter SMCS Code: 3067-510.Change the Filter
The transmission oil filter is located under the torque converter access cover. The transmission oil filter is the filter on the right hand side of the machine.1. Open the upper access cover. 2. Remove the filter housing drain plug and allow the oil to drain into a suitable container.3. Use a wrench to remove the filter housing.4. Remove and discard the used element.5. Clean the filter housing with a clean, nonflammable solvent.6. Clean the housing base.7. Inspect the filter housing seal. Replace the seal, if it is damaged.8. Insert a new element into the filter housing.9. Clean and install the filter housing drain plug. Install the filter housing into the housing base.10. Start the engine. Apply the service brakes. Use the right brake pedal only.11. Release the parking brake. Slowly operate the transmission controls to circulate the transmission oil.12. Move the transmission directional control to NEUTRAL. Engage the parking brake.13. Inspect the transmission filter for leaks.14. Open the transmission access cover located on the platform near the operator's station. 15. Maintain the oil level between the LOW and FULL marks on dipstick (1). Add oil through fill tube (2) if necessary.16. Close the access covers and stop the engine. Brake and Pilot Oil Filter SMCS Code: 5068-510.Change the Filter
The brake and pilot oil filter is located under the torque converter access cover. The brake and pilot oil filter is the filter on the left or operator's side of the machine.1. Open the upper access cover. 2. Remove the filter housing drain plug and allow the oil to drain into a suitable container.3. Use a wrench to remove the filter housing.4. Remove and discard the used element.5. Clean the filter housing with a clean, nonflammable solvent.6. Clean the housing base.7. Inspect the filter housing seal. Replace the seal if it is damaged.8. Insert a new element into the filter housing.9. Clean and install the filter housing drain plug. Install the filter housing into the housing base.10. Start the engine and run at low idle. Check for leaks. Hydraulic Oil System SMCS Code: 5068-510Change the Filters
1. Open the hydraulic tank access cover located on the right hand side of the machine.2. Relieve the hydraulic tank pressure by pushing on top of relief valve (1) before changing the filters. 3. Remove filter access cover (2) on the hydraulic tank guard.4. Remove the filter covers.5. Inspect the cover seals. Replace if necessary.6. Remove and discard the four filter elements.7. Remove oil filler cap (3). 8. Remove hydraulic tank oil filler screen (4). Wash the screen and the filter covers in clean, nonflammable solvent.9. Install the screen and four new filter elements. 10. Install the covers. Tighten the cover bolts to 56 3 N m (41 2 lb ft).11. Inspect the filler cap gasket. Replace the gasket if it

Caterpillar parts catalog:

Caterpillar parts catalog
627B SCRAPER 37V00637-01059 (MACHINE) POWERED BY 3306 ENGINE
627 SCRAPER 37V00001-00636 (MACHINE)


Parts retainer Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.