6I9719 RETAINER Caterpillar parts
D9N, D9R
Rating:
Alternative (cross code) number:
CA6I9719
6I-9719
6I9719
CA6I9719
6I-9719
6I9719
Weight: 11 pounds 5 kg.
TRACK-TYPE TRACTOR,
Number on catalog scheme:
3
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Bolt
1/2 inch - 20 UNF by 4 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01343963
Typical example
Always wear protective gloves when handling parts that have been heated.
If the flywheel ring gear was removed, follow Steps 1.a through 1.c to install a new ring gear to the flywheel.
Identify the orientation of teeth (4) on the new ring gear (4).Note: The chamfered side of the ring gear teeth must face toward the starting motor when the flywheel is installed. The correct orientation of the chamfered will ensure the correct engagement of the starting motor.
Heat flywheel ring gear (3) in an oven to a maximum temperature of 250 °C (482 °F) prior to installation.Note: Do not use a torch to heat the ring gear.
Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear onto flywheel (1).
Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" for the correct procedure.
Illustration 2 g01401982
Typical example
Install a suitable lifting device to flywheel (1). The weight of flywheel (1) is approximately 71 kg (155 lb).
Install Tooling (A) to Positions (X) on the crankshaft.
Use the lifting device to position flywheel (1) onto Tooling (A).
Install bolts (2) to flywheel (1) finger tight.
Remove Tooling (A) and install remaining bolts (2) to the flywheel (1).
Remove the lifting device from flywheel (1).
Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) to a torque of 140 N m (103 lb ft).
Check the run out of the flywheel. Refer to System Operation, Test, and Adjusting, "Flywheel - Inspect" for further information.End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Bolt
1/2 inch - 20 UNF by 4 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01343963
Typical example
Always wear protective gloves when handling parts that have been heated.
If the flywheel ring gear was removed, follow Steps 1.a through 1.c to install a new ring gear to the flywheel.
Identify the orientation of teeth (4) on the new ring gear (4).Note: The chamfered side of the ring gear teeth must face toward the starting motor when the flywheel is installed. The correct orientation of the chamfered will ensure the correct engagement of the starting motor.
Heat flywheel ring gear (3) in an oven to a maximum temperature of 250 °C (482 °F) prior to installation.Note: Do not use a torch to heat the ring gear.
Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear onto flywheel (1).
Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" for the correct procedure.
Illustration 2 g01401982
Typical example
Install a suitable lifting device to flywheel (1). The weight of flywheel (1) is approximately 71 kg (155 lb).
Install Tooling (A) to Positions (X) on the crankshaft.
Use the lifting device to position flywheel (1) onto Tooling (A).
Install bolts (2) to flywheel (1) finger tight.
Remove Tooling (A) and install remaining bolts (2) to the flywheel (1).
Remove the lifting device from flywheel (1).
Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) to a torque of 140 N m (103 lb ft).
Check the run out of the flywheel. Refer to System Operation, Test, and Adjusting, "Flywheel - Inspect" for further information.End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
Caterpillar parts catalog:
Parts retainer Caterpillar catalog:
578, 583R, D8N, D8R, D9N, D9R
834G, 834H, 834K, 844, 844H, 844K, 8U, D8L, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
320D, 320D GC, 320D L, 320D LRR, 320D RR, 322B L, 325B L, 330B L, 375 L, 950H, 962H, 994, 994D, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
583R, 583T, 587R, 587T, D8R, D8R II, D8T, D9N, D9R, D9T, PL83, PL87
631D, 631E, 631G, 637E, 637G, 641B, 651B, 657B, 657E, 657G, 854G, 8B, 8D, 950, 9B, D10, D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D7H, D7R, D8K, D8L, D8N, D8R, D8R II, D8T, D9H, D9L, D9N, D9R
173B, 183B, 844, 844H, 844K, D10N, D10R, D10T, D7G, D8L, D9H, D9L, D9N
24H, 24M, 641B, 651E, 657B, 657E, 657G, 69D, 735, 735B, 740, 740B, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772G, 772G OEM, 773B, 773D, 773E, 773F, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F,...
D9R, D9T
D9N, D9R, D9T
375, 854G, D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D9R, D9T
D9R, D9T
D10N, D10R, D10T, D10T2, D8L, D9L, D9N, D9R, D9T
D9N, D9R, D9T
1Q3626
RETAINER
D10N, D10R, D10T, D10T2, D9R, D9T
D10N, D10R, D10T, D10T2, D9R, D9T
1331121
RETAINER
D10N, D10R, D9R
D10N, D10R, D9R
1Q3528
RETAINER
D9R
D9R
D9R, D9T
1158384
RETAINER
D10N, D10R, D10T, D11R, D11T, D8L, D9N, D9R
D10N, D10R, D10T, D11R, D11T, D8L, D9N, D9R
1Q3553
RETAINER
D8R
D8R
1Q3272
RETAINER AS-SEAL
D10R, D9R
D10R, D9R
375, 854G, D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D9R, D9T
9W4803
RETAINER
D10N, D11N, D9L, D9N, D9R
D10N, D11N, D9L, D9N, D9R
8E4037
RETAINER
D9R, D9T
D9R, D9T
8E4648
RETAINER
D9R, D9T
D9R, D9T