6K5745 RETAINER Caterpillar parts
916, 920, 926, 930, 930R, IT18B, IT28, IT28B
Rating:
Alternative (cross code) number:
CA6K5745
6K-5745
6K5745
CA6K5745
6K-5745
6K5745
Weight: 4 pounds 1 kg.
INTEGRATED TOOLCARRIER, WHEEL LOADER,
Related part:
6K5745
RETAINER-BRG-YM
3309281
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$47.00
16 Jul 2022
US: Florida-Parts-Z
6K5745 - Retainer-Bearing for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
Compatible equipment models: 6K5745:
Information:
REMOVE CRANKSHAFT REAR SEAL AND WEAR SLEEVE
start by:a) remove flywheel Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a unit. If the seal is put back on the sleeve, the seal will be damaged.1. Remove the bolts from adapter (1) and install two 5/16" - 18 NC forcing screws in the adapter to remove it from the drive housing.2. Remove O-ring seal (3) and crankshaft seal (2) from adapter (1).3. Install tool (B) in adapter bore as shown. 4. Install tool (A) between tool (B) and wear sleeve (4). Turn tool (A) until the edge of the tool makes a flat place (crease) in the wear sleeve. Do this in several places around the wear sleeve until the sleeve can be removed from the end of the crankshaft by hand. INSTALL CRANKSHAFT REAR SEAL AND WEAR SLEEVE
Refer to Special Instruction, SMHS8508, for additional tooling required for the installation of Crankshaft Rear Seal and Wear Sleeve on other applications. Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a unit. If the seal is put back on the sleeve, the seal will be damaged.1. Install adapter (3) on tooling (A) as shown.
CAUTION If the crankshaft seal and wear sleeve come apart during installation, the seal and sleeve become scrap and a new seal and sleeve as a unit must be used as a replacement.
The rear seal and wear sleeve can not be exchanged with the front seal and wear sleeve. There are grooves in the sealing lip of the seals that direct the oil back into the crankcase as the crankshaft turns. An exchange of front and rear seals can cause the oil to come out of the crankcase.2. Put crankshaft seal (1) and wear sleeve (2) as a unit in position on adapter (3). Make sure the lip of the seal is up as shown. 3. Install tool (B) over the studs of tooling (A). Install nuts (C) and tighten the nuts evenly until the seal is against the bottom of the adapter bore.4. Remove nuts (C), tool (B) and tooling (A) from the adapter. Do not put engine oil on the lip of the seal during installation. Lubrication of the seal at installation can be a wrong indication for linkage at a later time.5. Put clean engine oil on the O-ring seal and install the seal on the adapter.6. Install tooling (D) on the end of the crankshaft.7. Install guide bolts (E) in the drive housing. Put adapter (3) in position on guide bolts (E) and over tooling (D). Make sure the wear sleeve makes contact with the end of the crankshaft.8. Install tool (B) over the small outside diameter of tool (F) until tool (B) is against the shoulder on tool (F).9. Install tooling (B) and (F) as a unit on the guide bolts and over locator.10. Put clean engine oil on the
start by:a) remove flywheel Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a unit. If the seal is put back on the sleeve, the seal will be damaged.1. Remove the bolts from adapter (1) and install two 5/16" - 18 NC forcing screws in the adapter to remove it from the drive housing.2. Remove O-ring seal (3) and crankshaft seal (2) from adapter (1).3. Install tool (B) in adapter bore as shown. 4. Install tool (A) between tool (B) and wear sleeve (4). Turn tool (A) until the edge of the tool makes a flat place (crease) in the wear sleeve. Do this in several places around the wear sleeve until the sleeve can be removed from the end of the crankshaft by hand. INSTALL CRANKSHAFT REAR SEAL AND WEAR SLEEVE
Refer to Special Instruction, SMHS8508, for additional tooling required for the installation of Crankshaft Rear Seal and Wear Sleeve on other applications. Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a unit. If the seal is put back on the sleeve, the seal will be damaged.1. Install adapter (3) on tooling (A) as shown.
CAUTION If the crankshaft seal and wear sleeve come apart during installation, the seal and sleeve become scrap and a new seal and sleeve as a unit must be used as a replacement.
The rear seal and wear sleeve can not be exchanged with the front seal and wear sleeve. There are grooves in the sealing lip of the seals that direct the oil back into the crankcase as the crankshaft turns. An exchange of front and rear seals can cause the oil to come out of the crankcase.2. Put crankshaft seal (1) and wear sleeve (2) as a unit in position on adapter (3). Make sure the lip of the seal is up as shown. 3. Install tool (B) over the studs of tooling (A). Install nuts (C) and tighten the nuts evenly until the seal is against the bottom of the adapter bore.4. Remove nuts (C), tool (B) and tooling (A) from the adapter. Do not put engine oil on the lip of the seal during installation. Lubrication of the seal at installation can be a wrong indication for linkage at a later time.5. Put clean engine oil on the O-ring seal and install the seal on the adapter.6. Install tooling (D) on the end of the crankshaft.7. Install guide bolts (E) in the drive housing. Put adapter (3) in position on guide bolts (E) and over tooling (D). Make sure the wear sleeve makes contact with the end of the crankshaft.8. Install tool (B) over the small outside diameter of tool (F) until tool (B) is against the shoulder on tool (F).9. Install tooling (B) and (F) as a unit on the guide bolts and over locator.10. Put clean engine oil on the
Cat SIS web machinery list:
Parts retainer Caterpillar catalog:
3G2714
RETAINER-SEAL
183B, 528, 528B, 530B, 561H, 561M, 613B, 613C, 613C II, 613G, 631C, 639D, 641B, 650B, 651E, 657E, 657G, 916, 926, 930R, 988, D250B, D300B, D7G, IT18B, IT28
183B, 528, 528B, 530B, 561H, 561M, 613B, 613C, 613C II, 613G, 631C, 639D, 641B, 650B, 651E, 657E, 657G, 916, 926, 930R, 988, D250B, D300B, D7G, IT18B, IT28
3G1264
RETAINER
163, 183B, 572G, 594H, 611, 613C, 613C II, 613G, 615C, 621B, 621E, 621F, 621G, 623B, 623E, 623F, 623G, 627B, 627E, 627F, 627G, 633C, 633D, 641B, 651E, 657E, 657G, 772, 814, 814B, 814F, 814F II, 815B, ...
163, 183B, 572G, 594H, 611, 613C, 613C II, 613G, 615C, 621B, 621E, 621F, 621G, 623B, 623E, 623F, 623G, 627B, 627E, 627F, 627G, 633C, 633D, 641B, 651E, 657E, 657G, 772, 814, 814B, 814F, 814F II, 815B, ...
5V4907
RETAINER
518, 518C, 528, 528B, 530B, 613C, 613C II, 814B, 815B, 816B, 824C, 826C, 916, 920, 926, 930, 936, 936F, 950, 950B, 950B/950E, 950F, 950F II, 966D, 966F, 970F, 980C, 980F, D250B, D25C, D300B, D30C, D35...
518, 518C, 528, 528B, 530B, 613C, 613C II, 814B, 815B, 816B, 824C, 826C, 916, 920, 926, 930, 936, 936F, 950, 950B, 950B/950E, 950F, 950F II, 966D, 966F, 970F, 980C, 980F, D250B, D25C, D300B, D30C, D35...
4D2305
RETAINER
613C, 621E, 631E, 641B, 657, 769C, 769D, 771C, 771D, 772, 773B, 773D, 775B, 775D, 776C, 776D, 777, 777D, 784B, 785B, 789B, 793B, 793C, 920, 926, 930, 936F, 950, 950F, 950F II, 966C, 966D, 966F, 966F I...
613C, 621E, 631E, 641B, 657, 769C, 769D, 771C, 771D, 772, 773B, 773D, 775B, 775D, 776C, 776D, 777, 777D, 784B, 785B, 789B, 793B, 793C, 920, 926, 930, 936F, 950, 950F, 950F II, 966C, 966D, 966F, 966F I...
1S3612
RETAINER-VALVE
613C, 621E, 631E, 641B, 657, 769C, 769D, 771C, 771D, 772, 773B, 773D, 775B, 775D, 776C, 776D, 777, 777D, 784B, 785B, 789B, 793B, 793C, 920, 926, 930, 936F, 950, 950F, 950F II, 966C, 966D, 966F, 966F I...
613C, 621E, 631E, 641B, 657, 769C, 769D, 771C, 771D, 772, 773B, 773D, 775B, 775D, 776C, 776D, 777, 777D, 784B, 785B, 789B, 793B, 793C, 920, 926, 930, 936F, 950, 950F, 950F II, 966C, 966D, 966F, 966F I...
9V2412
RETAINER
916, 924F, 924G, 924GZ, 924H, 924HZ, 924K, 926, 928F, 928G, 928H, 928HZ, 930G, 930K, 938F, 938G, 938G II, 938H, 938K, IT18B, IT18F, IT24F, IT28, IT28B, IT28F, IT28G, IT38F, IT38G, IT38G II, IT38H
916, 924F, 924G, 924GZ, 924H, 924HZ, 924K, 926, 928F, 928G, 928H, 928HZ, 930G, 930K, 938F, 938G, 938G II, 938H, 938K, IT18B, IT18F, IT24F, IT28, IT28B, IT28F, IT28G, IT38F, IT38G, IT38G II, IT38H
7G5220
RETAINER
518, 518C, 528, 910E, 910G, 914G, 918F, 920, 924F, 924G, 924GZ, 924H, 924HZ, 924K, 928G, 928H, 928HZ, 930, 930G, 930K, 938K, 950, 966C, FB518, IT12B, IT14B, IT14G, IT14G2, IT18F, IT24F, IT28G
518, 518C, 528, 910E, 910G, 914G, 918F, 920, 924F, 924G, 924GZ, 924H, 924HZ, 924K, 928G, 928H, 928HZ, 930, 930G, 930K, 938K, 950, 966C, FB518, IT12B, IT14B, IT14G, IT14G2, IT18F, IT24F, IT28G
6W3331
RETAINER
916, 918F, 924F, IT18, IT18B, IT18F, IT24F
916, 918F, 924F, IT18, IT18B, IT18F, IT24F
5K3274
RETAINER
518, 930, 930R
518, 930, 930R
6K5621
RETAINER
920
920
1V9809
RETAINER
814B, 815B, 824C, 826C, 834B, 836, 916, 926, 936, 936F, 950B, 950F, 950F II, 966D, 966F, 980C, 980F, 988B, 992C, 994, G936, IT18B, IT28B
814B, 815B, 824C, 826C, 834B, 836, 916, 926, 936, 936F, 950B, 950F, 950F II, 966D, 966F, 980C, 980F, 988B, 992C, 994, G936, IT18B, IT28B
5V5632
RETAINER-OIL SEAL
518, 926, 936, D250B, D250E, D300B, D300D, G936, IT28
518, 926, 936, D250B, D250E, D300B, D300D, G936, IT28
5J3150
RETAINER
621, 641, 650B, 651, 657B, 666, 992
621, 641, 650B, 651, 657B, 666, 992
5J2984
RETAINER
621, 631C, 641, 650B, 651, 657B, 666, 992
621, 631C, 641, 650B, 651, 657B, 666, 992
2S0642
RETAINER
621, 621B, 627B, 631C, 637D, 641B, 650B, 657B, 666B, 777
621, 621B, 627B, 631C, 637D, 641B, 650B, 657B, 666B, 777
2S5848
RETAINER
621, 631C, 650B
621, 631C, 650B
5J2888
RETAINER
621, 621B, 627, 627B
621, 621B, 627, 627B
5K3274
RETAINER
518, 930, 930R
518, 930, 930R
3J6955
RETAINER
631C, 641, 641B, 651, 657, 824B, 834, 988
631C, 641, 641B, 651, 657, 824B, 834, 988
5J9260
RETAINER
14E, 16, 631C, 641, 641B, 824B, 834, 834B, 836, 988B, 988F, 988F II, 992C, 992D, R1700 II
14E, 16, 631C, 641, 641B, 824B, 834, 834B, 836, 988B, 988F, 988F II, 992C, 992D, R1700 II
7J3633
RETAINER
641, 641B, 657B
641, 641B, 657B
9S9893
RETAINER
641B
641B
5J8773
RETAINER
621, 621B, 631C, 639D, 641B, 651
621, 621B, 631C, 639D, 641B, 651
3S5860
RETAINER
650B, 657, 834, D9G
650B, 657, 834, D9G