AVSPARE.COM
parts catalog

RING-PISTON 0000566 - Caterpillar



0000566 RING-PISTON Caterpillar parts RING
Rating:
16
Alternative (cross code) number:
CA0000566
000-0566
0000566
Caterpillar 0000566 RING-PISTON
Weight: 0.30 pounds 0 kg.

Buy RING-PISTON 0000566 Caterpillar genuine, new aftermarket tractor parts with delivery

You can buy parts: .

$27.72

04 Jun 2021

US: All Star Supplies, Corp.
Bulbtronics TUNGSTEN-HALOGEN Lamp 130V 60W 566
Bulbtronics Bulb, Osram Sylvania || PAR16 || 130V || 50.8 mm || 73.03 mm
  For full view, you need register

Information:


Illustration 1 g03037999
Schematic of the Solenoid for the Right Blade Angle
This diagnostic code is recorded when the current of the solenoid is below normal. Note: Ensure that the diagnostic code for the solenoid is on hold and that the fault present indicator shows "SERV CODE". This procedure can cause new diagnostic codes to be recorded. Ignore these created problems. When the procedure is completed, clear the created problems. Test Step 1. CHECK THE SOLENOID.
Turn the key start switch to the ON position. Ensure that the diagnostic code is on hold.
Disconnect the machine harness from the priority valve solenoid.
At the machine harness connector for the solenoid, place a jumper from contact 1 to contact 2.
Observe the status of the fault present indicator. Expected Result:"SERV CODE" is displayed and "SERV CODE" is NOT displayed as the jumper is installed and the jumper is removed.Results:
YES - The circuit is correct. The solenoid has failed. repeat this test step in order to verify that the solenoid has failed.Repair: Replace the solenoid.STOP
NO - The diagnostic code remains. Proceed to test step 2.Test Step 2. CHECK THE SIGNAL CIRCUIT FOR THE SOLENOID FOR AN OPEN.
Turn the key start switch to the OFF position.
Disconnect the machine harness connectors from the ECM.
The jumper wire remains installed.
At machine harness connector, measure the resistance from the contact 1 (F788-PU(Purple)) to the contact 2 (K975-WH(White)). Expected Result:There should be less than 5.0 ohms resistance.Results:
OK - The machine harness is correct. Proceed to test step 3.
NOT OK - There is an open circuit in the machine harness. The harness has failed.Repair: The open is in wire F788-PU(Purple) or in wire 975-WH(White) of the machine harness. Repair the machine harness or replace the machine harness.STOPTest Step 3. DETERMINE IF THE DIAGNOSTIC CODE IS STILL ACTIVE.
Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the key start switch to the ON position.
Enter service mode of the Caterpillar Monitoring System and clear all inactive diagnostic codes.
Operate the machine.
Stop the machine and place the parking brake switch in the OFF position.
Determine if the diagnostic code is present. Expected Result:The diagnostic code is present. "SERV CODE" is showing.Results:
YES - The problem has not been corrected. The ECM has failed.Repair: Exit this procedure and perform the diagnostic code procedure again. If the problem persists, the ECM may have failed. Prior to replacing an ECM, always contact your dealership's Technical Communicator for possible consultation with Caterpillar. This consultation may greatly reduce repair time. See the Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
NO - The diagnostic code is NOT present.Repair: The problem does not exist at this time. The initial problem was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.STOP


Parts ring Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.